Adsorption Behaviour of 134Cs and 22Na Ions on Tin and Titanium Ferrocyanides

Tin and titanium ferrocyanides were studied as adsorbents for alkali metal ions, viz., ¹³⁴Cs and ²²Na, which represent radioactive wastes. The ferrocyanides were prepared in granular form. The tin version contained 11.2% water, while the titanium version contained 17.7% water. The exchange capacities for Cs⁺ and Na⁺ in the hydrated tin version were about 1.5 and 0.7 meq/g, respectively, while those in the titanium version were 2.2 and 1.2 meq/g, respectively. Drying at 250°C decimated those capacities. The diffusional time constant of Cs⁺ at 25°C, determined via Fick's second law, was of order of magnitude 1 × 10^–3 s^–1, though there were minor differences due to particle size and the form of ferrocyanide. Similarly, the effective diffusivity was of order of magnitude 1 × 10^–8 cm²/s. The titanium version responded slightly faster than the tin version. Likewise, equilibrium measurements in mixtures with sodium nitrate, potassium nitrate, or uranium oxide, showed that the titanium version exhibited significantly greater selectivity for Cs⁺ than did the tin version. Unfortunately, tests of complete elution of the Cs⁺ from the ferrocyanides were mostly disappointing. Work continues on that subject.     

Self-bonding in an amorphous polymer below the glass transition: A T-peel test investigation

Films of amorphous polystyrene (PS) with a weight-average molecular weight (M_w) of 225 × 10³ g/mol were bonded in a T-peel test geometry, and the fracture energy (G) of a PS/PS interface was measured at the ambient temperature as a function of the healing time (t_h) and healing temperature (T_h). G was found to develop with (t_h)^1/2 at T_h = T_g-bulk − 33 °C (where T_g-bulk is the glass-transition temperature of the bulk sample), and log G was found to develop with 1/T_h at T_g-bulk − 43 °C ≤ T_h ≤ T_g-bulk − 23 °C. The smallest measured value of G = 1.4 J/m² was at least one order of magnitude larger than the work of adhesion required to reversibly separate the PS surfaces. These three observations indicated that the development of G at the PS/PS interface in the temperature range investigated (<T_g-bulk) was controlled by the diffusion of chain segments feasible above the glass-transition temperature of the interfacial layer, in agreement with our previous findings for fracture stress development at several polymer/polymer interfaces well below T_g-bulk. Close values of G = 8–9 J/m² were measured for the symmetric interfaces of polydisperse PS [M_w = 225 × 10³, weight-average molecular weight/number-average molecular weight (M_w/M_n) = 3] and monodisperse PS (M_w = 200 × 10³, M_w/M_n = 1.04) after healing at T_h = T_g-bulk − 33 °C for 24 h. This implies that the self-bonding of high-molecular-weight PS at such relatively low temperatures is not governed by polydispersity. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1861–1867, 2004     

Behavior and surface energies of polybenzoxazines formed by polymerization with argon,oxygen, and hydrogen plasmas

Polybenzoxazine (PBZZ) thin films can be fabricated by the plasma‐polymerization technique with, as the energy source, plasmas of argon, oxygen, or hydrogen atoms and ions. When benzoxazine (BZZ) films are polymerized through the use of high‐energy argon atoms, electronegative oxygen atoms, or excited hydrogen atoms, the PBZZ films that form possess different properties and morphologies in their surfaces. High‐energy argon atoms provide a thermodynamic factor to initiate the ring‐opening polymerization of BZZ and result in the polymer surface having a grid‐like structure. The ring‐opening polymerization of the BZZ film that is initiated by cationic species such as oxygen atoms in plasma, is propagated around nodule structures to form the PBZZ. The excited hydrogen atom plasma initiates both polymerization and decomposition reactions simultaneously in the BZZ film and results in the formation of a porous structure on the PBZZ surface. We evaluated the surface energies of the PBZZ films polymerized by the action of these three plasmas by measuring the contact angles of diiodomethane and water droplets. The surface roughness of the films range from 0.5 to 26 nm, depending on the type of carrier gas and the plasma‐polymerization time. By estimating changes in thickness, we found that the PBZZ film synthesized by the oxygen plasma‐polymerization process undergoes the slowest rate of etching in CF₄ plasma. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4063–4074, 2004     

The interfacial conformation of polypropylene glycols and foam behaviour

The foam behaviour of low molecular weight polypropylene glycols (PPG) was investigated as a function of concentration and molecular weight (190–2000 g mol⁻¹). For each polypropylene glycol, foam stability increases with concentration and passes through a maximum, beyond which foamability is suppressed as the solubility limit of the glycol is exceeded and droplets of glycol form. Light-scattering data as well as static and dynamic surface tension results provide the key information leading to these interpretations. A maximum in foamability was observed for the PPG molecules with increasing molecular weight (caused by a change in molecular conformation at the interface). This suppresses the Marangoni effect and leads to a decrease in foam stability.     

Study on the Superhydrophilicity of the SiO2-TiO2 Thin Films Prepared by Sol-Gel Method at Room Temperature

Nanoscale SiO₂-TiO₂ composite thin films with the thickness of about 100 nm were prepared by sol-gel method at room temperature in air. The chemical states of the elements on the surface and near the surface were measured by XPS. The results showed that the Ti on/near the surface of the thin films existed not only as TiO₂ but also as Ti₂O₃. Part of the TiO₂ was changed to Ti₂O₃ after UV irradiation. The crystalline structure of the TiO₂ in the SiO₂-TiO₂ thin films was anatase with the crystallite size of 14–20 nm. It was found that the thin film prepared at room temperature in air has good superhydrophilic property and has strong adherence to the substrate.     

Electrospinning of ultrafine cellulose acetate fibers: Studies of a new solvent system and deacetylation of ultrafine cellulose acetate fibers

Electrospinning of cellulose acetate (CA) in a new solvent system and the deacetylation of the resulting ultrafine CA fibers were investigated. Ultrafine CA fibers (∼2.3 μm) were successfully prepared via electrospinning of CA in a mixed solvent of acetone/water at water contents of 10–15 wt %, and more ultrafine CA fibers (0.46 μm) were produced under basic pH conditions. Ultrafine cellulose fibers were regenerated from the homogeneous deacetylation of ultrafine CA fibers in KOH/ethanol. It was very rapid and completed within 20 min. The crystal structure, thermal properties, and morphology of ultrafine CA fibers were changed according to the degree of deacetylation, finally to those of pure cellulose, but the nonwoven fibrous mat structure was maintained. The activation energy for the deacetylation of ultrafine CA fibers was 10.3 kcal/mol. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 5–11, 2004     

Statistical thermodynamics evaluation of polymer–polymer miscibility

The Simha and Somcynsky (S–S) statistical thermodynamics theory was used to compute the solubility parameters as a function of temperature and pressure [δ = δ(T, P)], for a series of polymer melts. The characteristic scaling parameters required for this task, P*, T*, and V*, were extracted from the pressure–temperature–volume (PVT) data. To determine the potential polymer–polymer miscibility, the dependence of δ versus T (at ambient pressure) was computed for 17 polymers. Close proximity of the δ versus T curves for four miscible polymer pairs: PPE/PS, PS/PVME, and PC/PMMA signaled the usefulness of this approach. It is noteworthy, that the tabulated solubility parameters (derived from the solution data under ambient conditions) propounded the immiscibility of the PVC/PVAc pair. The computed values of δ also suggested miscibility for polymer pairs of unknown miscibility, namely PPE/PVC, PPE/PVAc, and PET/PSF. In recognizing the limitations of the solubility parameter approach (the omission of several thermodynamic contributions), these preliminary results are auspicious because they indicate a new route for estimating the miscibility of any polymeric material at a given temperature and pressure. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2909–2915, 2004     

聚焦慢速高荷态重离子束微束斑X射线源

利用电子束离子源(EBIS)或者电子束离子陷阱(EBIT)产生的慢速高电荷态重离子束轰击金属靶面,离子束与靶面作用并复合辐射特征X射线;并将高荷态离子束采用离子光学系统会聚为微细束后再与靶面作用,能够辐射出微米甚至亚微米级、纳米级的微束斑X射线.本文介绍这一新型微束斑X射线源的结构、机理及其特性等.     

介质靶表面的充电效应对等离子体浸没离子注入过程中鞘层特性的影响

针对等离子体浸没离子注入技术在绝缘体表面制备硅薄膜工艺，采用一维脉冲鞘层模型描述介质靶表面的充电效应对鞘层厚度、注入剂量及靶表面电位等物理量的影响.数值模拟结果表明：随着等离子体密度的增高，表面的充电效应将导致鞘层厚度变薄、表面电位下降以及注入剂量增加，而介质的厚度对鞘层特性的影响则相对较小. 关键词： 等离子体浸没离子注入 脉冲鞘层 绝缘介质 充电效应     

强流束晕-混沌的外部磁场开关控制

研究了强流离子束在周期聚焦磁场通道中束晕-混沌的外部磁场开关参数控制方法. 将该方法应用在多粒子模型中，实现了对5种不同初始分布质子束的束晕-混沌的有效控制，得到了消除束晕及其再生现象的理想结果.在强流加速器系统中，由于外部磁场是可测和可调 的物理量，因此该控制方法有利于实验研究，可为强流质子加速器中周期聚焦磁场的设计和实验提供参考. 关键词： 强流离子束 周期聚焦磁场通道 束晕_混沌 混沌控制 开 关控制