两种方法制备ITO薄膜的红外特性分析

比较了用电束加热蒸发法和直流磁控溅射法制备的氧化锡铟(ITO)薄膜在红外波段的光学特性实验发现,通过直流磁控溅射在常温下制备的ITO薄膜在红外波段折射率稳定、消光系数小,比电子束加热蒸发制备的膜有较高的透过率在波长1550nm附近的透过率可达86%以上,消光系数约为004,方电阻最低为100Ω/□.     

相变光盘介电薄膜ZnS-SiO2 的微结构和光学特性

采用射频磁控溅射法制备了ZnS-SiO₂ 介电薄膜,利用透射电镜和椭偏仪研究了溅射条件对ZnS-SiO₂薄膜微结构和折射率n的影响.研究表明,ZnS-SiO₂薄膜中存在微小晶粒,大小为2～10 nm的ZnS颗粒分布在SiO₂基体中,当溅射功率和溅射气压变化时,ZnS-SiO₂薄膜的微结构和折射率n发生显著变化,微结构的变化是导致折射率n变化的主要原因,通过优化溅射条件可以制备适用于相变光盘的高质量ZnS-SiO₂介电薄膜.     

Experimental investigation of time-dependent cavitation in an oscillatory squeeze film

The occurrence of time-dependent cavitation and tensile stress in an oscillatory oil squeeze film were investigated experimentally. The test apparatus was a simple thrust bearing consisting of two parallel circular plates separated by a thin viscous oil film. During the test, one plate was at rest while the other (transparent) oscillated in a direction normal to its surface. This test configuration was chosen to avoid the rotational motion and complicated geometry of a squeeze film journal bearing. The frequency of oscillation was in the range of 5 to 50 Hz and was controlled by an electro-magnetic exciter. The process of cavity formation and its subsequent development was recorded by a high-speed video camera. Concomitant pressure in the oil film was measured both within and without the cavitation region. It was found that both tensile stress and cavities existed in a squeeze film under certain working conditions.     

蓝宝石R面上ZnO薄膜的NH3掺杂研究

以NH₃为掺杂源,利用金属有机化学气相沉积(MOCVD)系统在蓝宝石R面上生长出掺氮ZnO薄膜。通过XRD,SEM测量优化了其生长参数,在610℃和在80sccm的NH₃流量下生长出了〈1120〉单一取向的ZnO薄膜。经Hall电阻率测量,得知该薄膜呈现弱p型或高电阻率,并对其光电子能谱进行了研究。     

A new stochastic method of reconstructing porous media

We present a new stochastic method of reconstructing porous medium from limited morphological information obtained from two-dimensional micro- images of real porous medium. The method is similar to simulated annealing method in the capability of reconstructing both isotropic and anisotropic structures of multi-phase but differs from the latter in that voxels for exchange are not selected completely randomly as their neighborhood will also be checked and this new method is much simpler to implement and program. We applied it to reconstruct real sandstone utilizing morphological information contained in porosity, two-point probability function and linear-path function. Good agreement of those references verifies our developed method’s powerful capability. The existing isolated regions of both pore phase and matrix phase do quite minor harm to their good connectivity. The lattice Boltzmann method (LBM) is used to compute the permeability of the reconstructed system and the results show its good isotropy and conductivity. However, due to the disadvantage of this method that the connectivity of the reconstructed system’s pore space will decrease when porosity becomes small, we suggest the porosity of the system to be reconstructed be no less than 0.2 to ensure its connectivity and conductivity.     

Diffusion Structural Analysis Study of Titania Films Deposited by Sol-Gel Technique on Silica Glass

The diffusion structural analysis (DSA) was used to characterize microstructure changes of hydrous titania gel films under in situ conditions of heating. TG and DTA were used in order to elucidate the processes controlling the formation of anatase film during heating of hydrous titania gel film. The annealing of porosity and near surface structure defects of the dehydrated titania films was indicated by DSA in the temperature range 255–700°C as the decrease of radon release rate. It was demonstrated that the annealing was enhanced on heating in oxygen in comparison with heating in argon. The DSA experimental results were compared with model curves describing the radon diffusion mobility and the annealing of radon diffusion paths.     

分形介质的传热与传质分析(综述)

本文论述了分形介质的分形理论和数学基础,并简要综述了用分形理论和方法研究分形介质的传热与传质特性(如多孔介质的渗透率、热导率以及池核态沸腾换热)方面目前所取得的研究进展,最后扼要展望了用分形理论和方法进一步研究分形介质的传热与传质的可能的若干课题和方向。     

Modeling Media with Oriented Structures

Heterogeneity is typically the result of space variability of soil parameters at different scales. Soil anisotropy may be defined as the spatial persistence in some direction only, across coarse-grid elements, of heterogeneous structures with different characteristic lengths in different directions. One can account for the effect of these structures by upscaling soil properties. Analyzing flow in a strongly anisotropic structured soil at different scales evidences how transverse dispersion reduces to a subscale process, leading to mixing within the conductive structures.     

Control of self‐organized low‐dimensional morphology in poly(styrene‐b‐4vinylpyridine)/polystyrene blend thin films

The surface morphologies of poly(styrene‐b‐4vinylpyridine) (PS‐b‐P4VP) diblock copolymer and homopolystyrene (hPS) binary blend thin films were investigated by atomic force microscopy as a function of total volume fraction of PS (?_PS) in the mixture. It was found that when hPS was added into symmetric PS‐b‐P4VP diblock copolymers, the surface morphology of this diblock copolymer was changed to a certain degree. With ?_PS increasing at first, hPS was solubilized into the corresponding domains of block copolymer and formed cylinders. Moreover, the more solubilized the hPS, the more cylinders exist. However, when the limit was reached, excessive hPS tended to separate from the domains independently instead of solubilizing into the corresponding domains any longer, that is, a macrophase separation occurred. A model describing transitions of these morphologies with an increase in ?_PS is proposed. The effect of composition on the phase morphology of blend films when graphite is used as a substrate is also investigated. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3496–3504, 2004     

密封容器中后处理制备Tl2Ba2CaCu2Oy高温超导薄膜及其性能研究

以铝酸镧（001）单晶为基片，采用两步法制备Tl2Ba2CaCu2Oy（Tl 2212）高 温超导薄膜.首先，利用脉冲激光沉积（PLD）工艺沉积Ba2CaCu2Ox非晶前驱体薄膜；然后，前驱体薄膜在高温（720—850℃）下密封钢容器里铊化结晶形成Tl 2212薄膜.XRD结果表明Tl2212 薄膜是沿c轴方向生长的，其相组成为Tl 2212，摇摆曲线（0012）的半高宽为0.72° ，SEM图像显示其表面光滑平整，其零电阻温度为106.2K. 关键词： Tl 2212超导薄膜 脉冲激光沉积