Effect of the protonation level of poly(o-phenylenediamine) (PoPD) on the ac impedance of humidity-sensitive PoPD/poly(vinyl alcohol) composite film

A composite film consisting of poly(o-phenylenediamine) (PoPD) and poly(vinyl alcohol) (PVA) has been prepared, and the effect of the protonation level of PoPD on the response of the composite to humidity been investigated by ac impedance measurements. The electrochemical system of the PoPD/PVA composite in a humid atmosphere is represented by an electrochemical equivalent circuit containing film (R_film, C_film), Warburg (W) and interfacial (R_ct, C_dl) impedance. R_film was increased with decreasing protonation level of the PoPD in relative humidity regions higher than 40%, but it was almost independent of the protonation level in humidity regions lower than this percentage.     

迎头色谱程序升温脱附快速测定吸附热新方法

在Ｐｏｌａｎｙｉ吸附势理论基础上，结合程序升温脱附曲线的测定，建立了一个快速测定吸附热的新方法，详细讨论了该方法的原理，通过微机采样和数据处理，测定一条吸附热与覆盖度的曲线仅需１ｈ左右。     

碳纤维微电极研究(Ⅺ)——利用温度效应测定电极反应的热力学和动力学参数

研究了温度对碳纤维微电极上伏安曲线的影响及温度与电极电位的关系,测定了电极反应的热力学参数.由电流与温度的关系测定了去极剂的扩散活化能E_(al)和D_o,利用微电极具有高速传质的特性,测定了常规电极上为可逆反应的电极反应标准速率常数(?),并通过(?)与温度的关系测定了电极反应的活化能.     

Determination of glutamate pyruvate transaminase activity in clinical specimens using a biosensor composed of immobilized l-glutamate oxidase in a photo-crosslinkable polymer membrane on a palladium-deposited screen-printed carbon electrode

The determination of glutamate pyruvate activity (GPT) is of particular clinical importance. A portable GPT sensor for both diagnostic and home-care purpose is highly expected. A highly sensitive and stable l-glutamate sensor was fabricated for the rapid detection of the GPT activity in serum. The sensor is composed of immobilized l-glutamate oxidase in a photo-crosslinkable polymer (PVA-SbQ) membrane on a palladium-deposited screen-printed carbon electrode. The sensor exhibited high sensitivity (detection limit of 50 nM for monosodium glutamate), remarkable long-term stability in storage (5 months in the dry dark state and 1 month in buffer solution) and good reproducibility (R.S.D.=2.6%, n=100). The electrode-to-electrode reproducibility was found to depend on the composition of the polymeric matrix. The optimal substrate composition for the detection of GPT activity was 1 mM α-ketoglutarate and 100 mM l-alanine. The GPT activity in serum can be determined within 3 min. The response of the sensor to GPT activity is linear over the range of 8-250 U/l. Good correlation between the sensor and the Sigma GPT assay kit was achieved (R²=0.9958). The sensor is potentially applicable to a home-care purpose when a portable measuring device is adapted.     

Temperature selectivity effects in reversed-phase liquid chromatography due to conformation differences between helical and non-helical peptides

In order to characterize the effect of temperature on the retention behaviour and selectivity of separation of polypeptides and proteins in reversed-phase high-performance liquid chromatography (RP-HPLC), the chromatographic properties of four series of peptides, with different peptide conformations, have been studied as a function of temperature (5-80 degrees C). The secondary structure of model peptides was based on either the amphipathic alpha-helical peptide sequence Ac-EAEKAAKEX(D/L)EKAAKEAEK-amide, (position X being in the centre of the hydrophobic face of the alpha-helix), or the random coil peptide sequence Ac-X(D/L)LGAKGAGVG-amide, where position X is substituted by the 19 L- or D-amino acids and glycine. We have shown that the helical peptide analogues exhibited a greater effect of varying temperature on elution behaviour compared to the random coil peptide analogues, due to the unfolding of alpha-helical structure with the increase of temperature during RP-HPLC. In addition, temperature generally produced different effects on the separations of peptides with different L- or D-amino acid substitutions within the groups of helical or non-helical peptides. The results demonstrate that variations in temperature can be used to effect significant changes in selectivity among the peptide analogues despite their very high degree of sequence homology. Our results also suggest that a temperature-based approach to RP-HPLC can be used to distinguish varying amino acid substitutions at the same site of the peptide sequence. We believe that the peptide mixtures presented here provide a good model for studying temperature effects on selectivity due to conformational differences of peptides, both for the rational development of peptide separation optimization protocols and a probe to distinguish between peptide conformations.     

The effect of calcination conditions on the superconducting properties of Y−Ba−Cu−O powders

Calcination conditions of the precursor powders, i.e. temperature, type of atmosphere and duration, were determined with a view to obtain superconducting powders with the most advantageous physico-chemical properties. Investigated were powders in the Y?Ba?Cu?O system prepared by the sol-gel method. Thermogravimetric examinations of the powders have revealed that the decomposition kinetics of BaCO₃ determines the formation rate of the superconducting YBa₂Cu₃O_7?x (‘123’) phase. It follows from the decomposition kinetics of BaCO₃ that the process is the most intensive in argon, whereas in static air and oxygen it is the slowest. The phase composition analysis (XRD) and low-temperature magnetic susceptibility measurements of the calcinated powders, confirm the above mentioned changes in the decomposition kinetics. The reaction of barium carbonate can be completed if the calcination process is conducted at the temperature of 850°C for 25 h, yielding easily sinterable powders for obtaining single-phase superconducting bulk samples with advantageous functional parameters.     

Influence of the heating rate on the temperature profiles and on the conversion rate of powdery cellulose and pine sawdust

An experimental study of the thermal decomposition of powdered cellulose and pine sawdust has been performed. The influence of the heating rate on the temperature profiles in the sample and on the solid conversion rate has been studied. A mathematical model without adjustable parameters has been used to calculate the temperature at different points in the solid bed and the average total solid conversion. The experimental results have been compared with those calculated by the model. A good agreement has been obtained for sawdust. Some differences are observed for cellulose at high heating rates, and the influence of the thermal conductivity and the reaction heat on the results has been analysed.     

A nanoscale vesicular polydiacetylene sensor for organic amines by fluorescence recovery

We report a nanoscale lipid membrane-based sensor of conjugated polydiacetylene (PDA) vesicles for fluorescence detection of organic amines. The vesicle sensor was constructed by incorporation of a BODIPY fluorescent dye into the PDA vesicles. The fluorescent properties of the resulting vesicles can be manipulated by adjusting lipid components, and are controlled by environmental and solution conditions. The fluorescence of the BODIPY dye was significantly quenched in the polymerization of diacetylene lipid vesicles by a UV irradiation process. However, it was sufficiently recovered by external stimuli such as a hike of solution pH. The fluorescence recovery process was reversible, and a decrease in solution pH resulted in repeated quenching. The reported system transforms an external stimulus into a large fluorescence intensity change, demonstrating great potential in developing new signal reporting method for biosensor design. The quench-recovery phenomenon of the BODIPY-PDA is believed to be related to the energy transfer between the dye and the PDA conjugate backbone. The vesicle sensor was applied for detecting an organic amine, triethylamine (TEA) and a large linear relationship was obtained between the increase in fluorescence intensity and the concentrations of TEA. The detection limit of TEA by vesicle sensors using fluorescence recovery was found to be 10 μM.     

Improving the lower detection limit of potentiometric sensors by covalently binding the ionophore to a polymer backbone

The lower detection limit of polymeric membrane ion-selective electrodes (ISEs) is impaired by zero-current ion fluxes through the organic phase. This adverse effect is largely eliminated by covalently attaching the ionophore to a polymer backbone. To this purpose, the Pb²⁺-selective ligand, 4-tert-butylcalix[4] arene-tetrakis(N,N′-dimethylthioacetamide) is substituted on its upper rim by a diol derivative which is subsequently copolymerized with poly(tetrahydrofuran)diol and 2,2,4-trimethylhexamethylene diisocyanate to the corresponding polyurethane. By measurements on sandwich membranes, it is shown that through binding the ionophore to the polymer, the mobility of Pb²⁺ in the ISE membrane is strongly reduced. As a consequence, the response range of such an ISE is extended by several orders of magnitude. This is the case even when using an internal electrolyte that with an ISE based on a mobile ionophore leads to strong deviations from the linear response because of ion uptake from the sample into the membrane or ion release from the membrane into the sample. With a conventional inner filling solution of 10⁻¹ M Pb(NO₃)₂, a lower detection limit of 1.7×10⁻⁹ M Pb²⁺ has been achieved in the presence of 10⁻⁴ M Na⁺.     

纳米硅胶颗粒的制备及其对金属离子的识别

利用sol-gel方法制得了纳米级的硅胶悬浮液.通过表面化学修饰引入了具有发射荧光能力的萘基基团.在稳态荧光研究中清晰地观察到在微小粒子表面上萘基基团会因溶剂不同而发生重新排组,并呈现出激基缔合物发光.研究了不同过渡金属离子对粒子表面荧光的猝灭效应,发现只有Cu2＋对纳米微球荧光有强烈的猝灭特征,这种优良的选择能力使其有望发展成为一种分析检测Cu2＋的荧光化学敏感器.