LaB6在低压强氮气和氦气中的放电特性

 研究了LaB₆在1~10 Pa氮气和氦气中的直流和脉冲放电特性以及放电过程对电极的影响。结果表明，电极直径为5 mm的LaB6氦气放电管在脉冲工作状态下可以长期稳定放电。在脉冲电压为2.2 kV、脉冲宽度10 ms、频率13.3 Hz下，脉冲峰值放电电流超过120 A。氦气放电管在放电过程中，阴极表面有离子的清洗和活化作用，可以使电极的表面逸出功降低，提高放电管的发射能力和稳定性。LaB₆作为气体放电电极具有寿命长、延迟时间短、放电电流大等优点，可用于重复强流脉冲气体放电的高压高速开关器件。     

High-throughput concept for tailoring switchable mirrors

The optical properties, the switching kinetics and the lifetime of hydrogen switchable mirrors based on Mg-Ni alloys are determined with particular regard to the composition of the optically active metal-hydride layer in combination with the thickness of the catalytic capping layer. For this, a high-throughput experiment is introduced. The switching kinetics and the reversibility of switchable mirrors are strongly thickness dependent, though the details hinge on the fine structure of the clustered capping layer. Therefore, the kinetics is correlated with the surface structures of Pd on Mg_yNi_1−y as investigated by scanning tunneling microscopy. The results are explained by the so-called strong metal-support interaction (SMSI) state, characterized by a complete encapsulation of the capping layer clusters by oxidized species originating from the support. The SMSI-effect is less important with increasing Pd-layer thickness, and is suppressed by a good wetting of the Pd-clusters on the optically active film. This explains the critical thickness for the catalyzed hydrogen uptake observed in many switchable mirror systems. Moreover, the degradation of the kinetics during cycling is found to depend on the Pd-layer thickness and on the gas environment. Only films, covered with at least 15 nm Pd, show small degradation caused by the SMSI-effect. The SMSI-effect is partly reversible: after changing the gas environment from hydrogen to oxygen, the oxide on the Pd-clusters can be partly removed.     

Nanocrystalline ceramic films for efficient conversion of light into electricity

Transparent nanocrystalline films of oxide semiconductors such as TiO₂ and Fe₂O₃ have been prepared on a conducting glass support employing a sol-gel procedure. The films are composed of nanometer-sized particles sintered together to allow for percolative charge carrier transport. The internal surface of these films is very high, roughness factors of the order of 1000 being readily obtained. Electric polarization was applied for forward and reverse biasing of the films and the resulting optical changes have been analyzed to derive their flat band potential. Band gap excitation of such nanocrystalline semiconductors produces electron-hole pairs which migrate through the film to be collected as electric current. Steady state photolysis and time resolved laser techniques have been applied to scrutinize the mechanism of light induced charge separation within the nanostructure. When derivatized with a suitable chromophore, TiO₂ films give extraordinary efficiencies for the conversion of incident photons into electric current, exceeding 90% for certain transition metal complexes within the wavelength range of their absorption band. The underlying physical principles of these astonishing findings will be discussed. Exploiting this discovery, we have developed a new type of photovoltaic device whose overall light to electric energy conversion yield is 10% under simulated AM 1.5 solar radiation.     

一维应变压缩下TC4钛合金绝热剪切研究

 利用内径为57 mm的压缩气炮，在撞击速度为0.2~1.2 km/s（相应的靶中压力为3~15 GPa）范围内进行对称碰撞实验，以研究TC4（Ti-Al6-V4）钛合金在一维应变冲击压缩条件下的绝热剪切现象。对回收得到的受冲击样品，在扫描电镜（SEM）下进行细观金相分析。结果指出，一维应变冲击压缩条件下，TC4钛合金中绝热剪切带产生的对称碰撞速度阈值为500 m/s（相当于样品中的压力为5.87 GPa）；主剪切带与冲击方向约为45°角，带上有圆形和椭圆形两种孔洞且随碰撞速度的增大而增多和长大，这是典型的韧性损伤特征。随碰撞速度增大，产生与主剪切带成15°角的支剪切带。这些与理论预言相符。X射线能谱分析结果指出，剪切带内材料发生了(α+β)→β相的转变，是典型的相变带。剪切带的温度估算与实验提供的信息吻合。     

Effect of carbon content on the microstructure and the cracking susceptibility of Fe-based laser-clad layer

The laser cladding of Fe-based alloys on a medium carbon steel substrate was performed using a CO₂ laser and Ar shielding gas that was blown into a molten pool. The microstructure and cracking susceptibility of the laser-clad layers were studied in terms of carbon additions. Results show that the small change of the carbon content in the alloy powders can obviously change the microstructure and properties of the layers. When the carbon content is in the range of 0.3–0.4 wt.%, the decrease of the carbon content in alloy powders will increase the hardness and toughness of the layers simultaneously under the same process parameters. As a result, crack-free coatings with high hardness can be obtained. As the carbon content increases from 0.2 wt.% to 0.4 wt.%, the segregation ratio of chromium increases, while the segregation ratios of nickel, manganese, and silicon first decrease and then increase. At the same time, a new designing principle concerning the composition and microstructure has been put forward, and the principal mechanisms of strengthening and toughening of the layers are fine-grain strengthening and low carbon martensitic phase transformation strengthening.