Poly(N-isopropylacrylamide)-grafted dual stimuli-responsive filter paper for protein separation

Thermal and salt dual stimuli-responsive filter-paper-based membranes were prepared by UV-induced grafting of NIPAM-based polymers on paper surface. The grafting ratio could be controlled by monomer concentration during grafting polymerization. The results from pressure drop measurement of the mobile phase flowed cross the membrane demonstrate that an appropriate grafting ratio would be 8%-10%. Protein adsorption on the membrane through hydrophobic interaction could be promoted by increasing temperature and lyotropic salt concentration. The effect of grafted polymer structure on protein binding performance was studied. Filter paper grafted with NIPAM-based branched copolymer consisting of hydrophobic monomer moieties shows ten times higher protein binding capacity than that of the original filter paper. The separation of plasma proteins using the dual stimuli-responsive membrane was examined to demonstrate feasible application for hydrophobic interaction chromatographic separation of proteins.     

静电纺丝法制备PLLA/g-HNTs复合纳米纤维膜及其性能研究

以辛酸亚锡为催化剂,利用HNTs表面的羟基引发L-LA开环聚合,合成了表面接枝聚(L-乳酸)(PLLA)链段的埃洛石纳米管(g-HNTs),通过红外、热失重和透射电镜对改性前后HNTs的组成与形貌进行了观察;然后采用静电纺丝技术制备了PLLA纳米纤维膜以及不同组成的PLLA/HNTs和PLLA/g-HNTs复合纳米纤维膜,探讨了纺丝条件对纳米纤维膜形貌的影响,并对复合膜的组成、形貌、力学性能和细胞相容性进行了研究.结果表明,当HNTs与L-LA的摩尔投料比为1∶10时,g-HNTs表面PLLA链段的接枝率为14.22％,HNTs纳米管的形态在接枝后变化不大,易于在无水乙醇中分散.电压强度和进样速率对纤维膜的形貌有一定影响,当电压强度为15 kV、进样速率为1 mL/h时,电纺纤维的直径较为均匀.复合纤维膜中g-HNTs在基体PLLA中的分散性以及与基体的界面相容性要优于相应的HNTs,当g-HNTs含量高达40％时,复合纳米纤维膜中的纤维形态仍然保持较好,可以得到连续、粗细较均匀的纤维;随着HNTs和g-HNTs含量增加,复合纳米纤维膜的拉伸强度和模量先增大后下降,当HNTs和g-HNTs的含量为5％时,两种复合纳米纤维膜的拉伸强度和模量均达到最大值,但PLLA/g-HNTs组复合纳米纤维膜的拉伸强度始终大于相应的PLLA/HNTs组.体外3T3细胞培养结果显示,PLLA/g-HNTs复合纳米纤维膜具有良好的细胞相容性,且优于相应的PLLA和PLLA/HNTs纳米纤维膜.     

Electrochemical performance of a nano SnO2-modified LiNi1/3Co1/3Mn1/3O2 cathode material

The nano SnO₂-modified LiNi_1/3Co_1/3Mn_1/3O₂ was successfully prepared by a carrier transfer method. The pristine and modified samples were characterized with various techniques such as XRD, SEM, XPS and EDS. The results showed that the SnO₂ particles did not enter the crystal structure of LiNi1/3Co1/ 3Mn1/3O₂, many nano SnO₂ particles were uniformly covered on the surface of LiNi_1/3Co_1/3Mn_1/3O₂ and the modified thin layer could inhibit the dissolution of transition metal oxides. The electrochemical tests indicated that the existence of nano SnO₂ could improve the discharge capacity and rate capability owing to the decreased interfacial polarization. The cycling stability was remarkably improved at room temperature and 55 ℃. The XRD patterns of the fresh NCM electrode and after 50 cycles proved that the structural change of NCM was not so effective on the capacity fade.     

基于单宁酸的功能材料研究进展

单宁酸(Tannic acid,TA)是一种天然植物多元酚,广泛分布于各类植物的根、茎、叶及果实中,具有价格低廉、来源广泛、生物相容性好等特点。单宁酸分子内含有大量酚羟基和酯基活性官能团,具有高化学反应活性。由于其特殊的分子结构——大量疏水芳香环和亲水酚羟基的存在,单宁酸还易与各种分子或基团形成氢键、静电、疏水和π-π堆叠等多种相互作用,在功能材料领域应用广泛。本文总结了近年来单宁酸在功能材料领域应用的研究进展,其中主要包括贵金属纳米材料制备、表界面功能化改性、功能微胶囊构筑和自组装材料制备等,并对基于单宁酸功能材料的研究前景进行了展望。     

基于表面起皱法的梯度图案的可控制备

报道了基于非刻蚀法的表面起皱机制来实现高分子薄膜表面的周期性梯度图案的简单可控制备.即对于处于机械拉伸状态的聚二甲基硅氧烷(PDMS)弹性基底,在其底部垫入"积木",而后对其进行紫外-臭氧(UVO)和氧等离子体(OP)的联合表面处理."积木"的加入引起了表面处理后表面硅氧层(SiOx)梯度厚度的形成,进而当释放拉伸应变后,诱导产生了梯度皱纹图案.结果表明:当UVO与OP联用处理时,不仅实现了较小拉伸应变下梯度皱纹形貌的制备,而且扩大了UVO单独使用时梯度皱纹周期的变化范围.通过OP与UVO的处理顺序和处理时间等因素的简单调节,进一步实现了不同梯度皱纹微结构的精细构筑.     

Improved water resistance of SrAl2O4: Eu2+, Dy3+ phosphor directly achieved in a water-containing medium

In this paper, a heterogeneous precipitation method utilizing urea hydrolysis was adopted to coat a SiO₂ layer on the surface of SrAl₂O₄:Eu²⁺, Dy³⁺ long persistence phosphors. To avoid phosphor hydrolysis in a water-containing coating medium, the hydrolysis and polymerization reactions of tetraethyl orthosilicate (TEOS) were concerned and carried out. The crystal phases, surface morphologies, hydrolysis stability and water resistance on afterglow properties of coated phosphors were investigated. Scanning electron microscopy, energy dispersive spectrum analysis, transmission electron microscope and Fourier transform infrared spectrum results confirmed that a continuous, uniform and compact SiO₂ coating layer was successfully obtained on the phosphors surface. A theoretical coating amount of 5% or higher was found to be good for hydrolysis stability. Photoluminescence results revealed the coated phosphors showed much better water resistance on afterglow properties than the uncoated phosphor. We also discussed and proposed the hydrolysis restriction mechanism of SrAl₂O₄:Eu²⁺, Dy³⁺ in the water-containing coating medium.     

Tuning the properties of a black TiO2-Ag visible light photocatalyst produced by a rapid one-pot chemical reduction

A highly efficient black TiO₂-Ag photocatalytic nanocomposite, active under both UV and visible light illumination, was synthesized by decorating the surface of 25 nm TiO₂ particles with Ag nanoparticles. The material was obtained via a rapid, one-pot, simple (surfactant and complexing agent free) chemical reduction method using silver nitrate and formaldehyde as a metal salt and reducing agent, respectively. The nanocomposite shows an increase of over 800% in the rate of photocatalytic methylene blue dye degradation, compared to commercial unmodified TiO_2, under UV-VIS illumination. Unlike pure TiO₂, the nanocomposite exhibits visible light activation, with a corresponding drop in optical reflectance from 100% to less than 10%. The photocatalytic properties were shown to be strongly enhanced by post-reduction annealing heat treatments in air, which were observed to decrease, rather than coarsen, silver particle size, and increase particle distribution. This, accompanied by a variation in the silver surface oxidation states, appear to dramatically affect the photocatalytic efficiency under both UV and visible light. This highly active photocatalyst could have wide ranging applications in water and air pollution remediation and solar fuel production.     

Wave-like deformations for oscillating carbon nanotubes

Carbon nanostructures such as nanotubes and fullerenes, represent future materials because of their remarkable mechanical, electrical and thermal properties. Double-walled carbon nanotubes are widely studied as possible gigahertz oscillators, where the inner tube oscillates within the outer tube. These oscillators are believed to generate frequencies in the gigahertz range and typically of the order of 1–74 GHz. They are also known to generate wave-like formations on the outer surface. In this paper, we study such induced deformations on the surface of the outer tube, as generated by the moving inner tube. Following previous authors we assume that double-walled carbon nanotubes can be modelled as transversely isotropic linearly elastic materials. Using a previously derived approximate force distribution for the resultant van der Waals forces arising from the interatomic interactions, we solve a dynamic linearly elastic problem, and show that the resulting solution exhibits wave-like behaviour.     

Onset of Surface Damage in Modular Orthopedic Implants: Influence of Normal Contact Loading and Stress-assisted Dissolution

Surface damage at interfaces of modular implants results from repeated fretting contacts between metallic surfaces in a corrosive environment. As a first step in understanding this complex process, multi-asperity contact experiments were conducted to characterize roughness evolution due to action of contact loads and exposure to a reactive environment. Cobalt–chromium specimens with surface roughness similar to modular implant were first subjected to only contact loading and subsequently, to alternating contact loads and exposure to reactive environment. During repeated normal contact loading, amplitude of surface roughness reached a steady value after decreasing during the first few cycles. However during the second phase surface roughness amplitude continuously evolved—decreasing during contact loading and increasing on exposure to corrosive environment. The increase in roughness amplitude during surface reaction depended on the magnitude of applied contact loads. A damage mechanism that incorporates contact-induced residual stress development and stress-assisted dissolution is proposed to elucidate the measured surface roughness evolution.     

Transient Waves on the Free Surface of a Viscoelastic Anisotropic Half-Space

The Stroh formalism is employed to discuss the existence of transient surface waves on a viscoelastic anisotropic hall-space. The compatibility conditions, obtained using the integral formulation of Lothe and Barnett [13, 14], are examined on the basis of an asymptotic expansion of the viscoelastic kernel and a separation of space variables. Some previous results on elastic media are extended to viscoelasticity, exploiting the consequences of the second law of thermodynamics. It is found that all the allowed transient surface modes take the form of inhomogeneous plane waves whose amplitude exponentially decays along the propagation direction on the surface. Special solutions are derived explicitly for one-component surface waves where transient modes are admitted also in those cases in which stationary waves cannot occur. Mathematics Subject Classifications (2000) 74D05, 74J15.