Morphology of peroxide-prevulcanised natural rubber latex: effect of reaction time and deproteinisation

A non-uniform mesh structure, i.e. a dense network near the surface of peroxide-prevulcanised natural rubber latex particles, was observed under transmission electron microscopy. In the initial period of prevulcanisation, the swelling ratio of the latex sheet decreased with longer reaction time while an increase in crosslink density of rubber particles containing polystyrene, prepared using the phase transfer/bulk polymerisation process, was noticed. The modulus of the rubber sheet increased up to maximum crosslinking and thereafter decreased. After removal of proteins from the latex membrane layer, derived from protein-lipid originally existing at the rubber particle surface, could not be detected. The absence of proteins, which act as free radical scavengers, resulted in a rapid diffusion of alkoxy radicals into the rubber phase of deproteinised latex and, therefore, a uniform crosslink distribution inside each particle was obtained.     

Surface diffusion in reversed-phase liquid chromatography using silica gels bonded with C1 and C18 ligands of different densities

Surface diffusion in reversed-phase liquid chromatography (RPLC) using silica gels bonded with C₁ and C₁₈ alkyl ligands of different densities was studied from the viewpoints of two extrathermodynamic relationships, i.e., enthalpy-entropy compensation (EEC) and linear free energy relationship (LFER). First, according to the four methods proposed by Krug et al., the values of surface diffusion coefficient (D_s) were analyzed to confirm that an actual EEC resulting from substantial physico-chemical effects takes place for surface diffusion. Then, it was also demonstrated that a LFER is observed between surface diffusion and the retention equilibrium. The establishment of EEC and LFER suggests a mechanistic similarity of molecular migration by surface diffusion, irrespective of the alkyl chain length and the densities of C₁ and C₁₈ ligands. Finally, a thermodynamic model for the LFER based on the real EEC was used to estimate D_s values under various RPLC conditions. The D_s values can be estimated with a mean square deviation of about 25–30%. The agreement between the D_s values estimated and those experimentally measured suggests that the total mass flux by surface diffusion consists of the two contributions due to C₁ and C₁₈ ligands and that the contribution of each ligand is proportional to the ligand density.     

Synthesis and characterisation of advanced UHMWPE/silver nanocomposites for biomedical applications

A supercritical fluid (SCF) route for facile and homogeneous introduction of silver nanoparticles into polymer hosts is described. Our focus is on ultra-high molecular weight polyethylene (UHMWPE). We demonstrate that the metallic nanoparticles have a substantial effect upon the wear and tribochemical properties of the polymer substrate.     

熔融碳酸盐燃料电池阳极材料表面改性

选择铌作为合金化元素，通过氟化物熔盐电化学表面合金化的方法对熔融碳酸盐燃料电池阳极材料镍进行表面改性，改性后的阳极材料的耐蚀性能与电催化性能均得到明显的改善。     

The physicochemical surface characteristics of Brevibacterium linens

The physicochemical surface characteristics and interfacial behavior of two strains of Brevibacterium linens (BL-MGE and BL-9174), that may enhance cheese flavor, were assessed. Cell surface hydrophobicity was determined by measuring the contact angle of a variety of polar and non-polar wetting agents on lawns of the bacterial cells. The contact angles obtained were used to calculate the cell surface free energy components γ^LW, γ^AB, γ⁺ and γ⁻. The Lifshitz van der Waals component and the Lewis acid-base component were approximately 35 mJ m⁻² and 22 mJ m⁻², respectively, for both strains. Under conditions of physiological pH and low ionic strength, neither strain exhibited affinity for an octyl ligand in hydrophobic interaction chromatography. This occurred despite a favorable free energy of interfacial interaction which was attributable almost entirely to favorable acid-base interactions between cells and octyl-sepharose. The nature of surface functional groups was evaluated using X-ray photoelectron spectroscopy. Excluding H, the mean percentage of atomic fraction for C, O, N and P for BL-MGE was 57.7, 37.8, 3.9 and 0.6%, respectively and 61.0, 31.8, 7.0 and 0.2%, respectively for BL-9174.     

Probing the surface polarity of native celluloses using genuine solvatochromic dyes

The surface polarity of native celluloses has been investigated by the following solvatochromic dyes: dicyano-bis (1,10)-phenanthroline iron (II) Fe(phen)2 (CN)2 (1), bis(4-N,N-dimethylamino)-benzophenone (2), and cou-marine 153 (3). Linear Solvation Energy (LSE) relationships and the UV/Vis data have been used to characterize the surface polarity of different native cellulose batches in terms of the empirical Kamlet–Taft polarity parameters (hydrogen bond acidity), (hydrogen bond basicity), and * (dipolarity/polarizability). , , *and calculated Reichardt's E T (30) values are reported for various native and regenerated cellulose samples with different degrees of crystallinity. The degree of crystallinity of the cellulose samples has been determined by X-ray. The microcrystalline environment of cellulose can be exactly parameterized in terms of the , and *values. It shows a fairly strong acidity and a low dipolarity/polarizability. For the amorphous sections smaller and larger * values are observed. The correspondence of the empirical polarity parameters determined has been discussed in relation to results from pyrene fluorescence and zetapotential measurements.     

关于超高分子量聚丙烯超拉伸膜的结构性能的研究——Ⅱ.形态结构变化对力学性能的影响

用X-射线衍射、动态力学测定等手段研究了不同拉伸倍数的超高分子量聚丙烯薄膜的力学性能的变化.以X-射线衍射法并基于串联力学模型的假设得到的各样品的表观晶区模量E_c~(app)约为34-38GPa.样品模量E_b随拉伸倍数增加而逐渐增大,其变化趋势与非晶区取向因子的变化相类似,说明非晶区取向是左右样品模量的重要因素.室温下,69倍拉伸样品的模量为27GPa,约为表观结晶模量的3/4,且其值在-150-160℃的温度范围内没有急剧变化,说明超拉伸明显改善了材料的力学性能及热稳定性.在各拉伸样品中,考虑伸直链结晶生成的可能性,利用并串联力学模型对伸直链结晶的体积分数做了估算,并对X-射线衍射法所得表观结晶模量进行了修正,认为室温下聚丙烯的真正晶区模量约为47GPa.     

A new approach to the design of surface treatments for reinforcing agents

A new approach for design of improved interfacial bonding between carbon fibers and polymeric matrices is described. In this method the affinity of surface-treated carbon fibers to various polymer matrices is simulated by analyzing the adsorption characteristics of model compounds, typical of the polymer units, onto very high surface area carbon fibers. The affinity can be evaluated by the use of Thermogravimetric Analysis (TGA) to measure adsorption–desorption characteristics. Since high surface area, activated carbon fibers (ACF) can be chemically treated to obtain acidic, basic, nonpolar or highly polar surfaces, it should be possible to assess the interactions of chemically modified surfaces with model compounds such as methanol (MeOH), acetone, dimethylformamide (DMF), dimethylether, tetrahydrofuran (THF) and water. Some preliminary results are presented, indicating that surface treatments for carbon fibers other than oxidation may lead to enhanced bonding with polymeric matrices.     

高密度聚乙烯／超高分子量聚乙烯共混物高取向薄膜形态结构与力学性能的研究

高密度聚乙烯／超高分子量聚乙烯共混物高取向薄膜形态结构与力学性能的研究张伟广，赵勇，杨德才中国科学院长春应用化学研究所，高分子物理开放实验室，长春，１３００２２）关键词ＨＤＰＥ、ＵＨＭＷＰＥ、共混物、形态结构、力学性能如何提高高分子材料抗张强度和模量...