基于悬臂梁的光纤光栅线性调谐器研究

分析了基于悬臂梁的光纤光栅线性调谐的基本原理及调谐公式,指出了调谐范围、调谐灵敏度和反射波谱展宽与悬臂梁结构的关系,并提出了优化方案.实验中选用适当尺寸的悬臂梁,对粘贴其上的光纤光栅的反射波长实现了线性调谐,并可对调谐范围、灵敏度等指标进行灵活控制.     

考虑温度效应的覆冰导线动力学建模及舞动特征研究

针对以往研究忽略了温度效应对覆冰导线舞动特性的影响,本文推导了考虑温度效应影响的覆冰导线舞动控制方程.基于悬链法、热应力理论推导了覆冰导线的偏微分舞动方程,接着通过Galerkin法将该偏微分方程转化为常微分方程.建立气动载荷模型,将气动力引入到舞动方程中,随后采用多尺度求得了覆冰导线的位移响应,最后进行了参数分析、算...     

用转移矩阵法数值研究二维正方介质柱光子晶体的传输特性

利用转移矩阵方法对二维正方介质柱光子晶体的传输特性进行了研究,数值计算研究了不同晶格、同一晶格柱体截面面积不同、放置方位角不同时光子晶体的传输特性。数值结果表明光子禁带的宽度与中心频率和晶格结构有很大关系,正方晶格更易形成平坦光子禁带,柱体截面面积大,则形成的禁带较宽,在其他因素相同的条件下柱体放置的方位角对光子禁带有重要影响。数值研究表明在正方介质柱下设计宽平坦光子禁带时,可以首先考虑正方晶格结构,其次设法使柱体截面尽量大一些,最后可通过柱体放置方位角来微调光子禁带的宽度与中心频率以达到设计要求。     

Time-averaged flow characteristics and mixing properties of double-concentric jets

We examined the flow behaviors and mixing characteristics of double-concentric jets using laser-assisted smoke flow visualization method to analyze typical flow patterns and binary boundary detection technique to investigate jet spread width. Time-averaged velocity vectors, streamline patterns, velocity distributions, turbulence properties, and vorticity contours were analyzed using Particle Image Velocimetry (PIV). Topological flow patterns were analyzed to interpret the vortical flow structures. Mixing properties were investigated using a tracer-gas concentration detection method. Four characteristic modes were observed: annular flow dominated mode, transition mode, central jet dominated mode-low shear, and central jet dominated mode-high shear. The jets’ mixing properties were enhanced by two major phenomena: the merging of annular flow and central jet at the centerline and the large turbulence fluctuations produced in the flow field. The merging of the jets induced stagnation points on the central axis in the annular flow dominated mode, which caused reverse flow on the central axis and drastic turbulence fluctuations of the near field region. When the central jet penetrated the recirculation region in the other three modes, the stagnation points on the central axis and the reverse flow vanished. Therefore, the mixing behaviors were prominently enhanced in the annular flow dominated mode.     

爆炸荷载作用下方形夹芯板动力学响应与优化设计数值分析

为研究方形蜂窝铝板在爆炸荷载作用下的动力学响应,基于LS-DYNA非线性有限元软件,建立了TNT炸药-前后面板-蜂窝夹芯-空气的三维有限元模型。采用ALE(任意的拉格朗日欧拉)多物质流固耦合算法分析了蜂窝铝板在冲击荷载作用下的变形机理、塑性变形、能量吸收以及结构的优化。数值模拟结果表明:随着面板厚度、核心高度的增加,蜂窝铝板在冲击荷载作用下的塑性变形明显减小,抵抗变形的能力增强;随着爆轰入射角度的增加,结构的破坏程度有所减小,入射角越大这种效果越发明显。对结构给定边长和受冲击面积以及面板厚度配合比、夹芯量纲为一的高度进行了局部的优化分析,为设计优质铝蜂窝板提供参考。     

浙江省城镇建设用地空间扩展时空特征分析

运用1990~2015年浙江省6期土地利用数据, 使用扩展速率、扩展强度、分形维数等指标分析浙江省城镇建设用地空间格局. 结果表明 (1)1990~2015年, 浙江省城镇建设用地增长在5个时期呈现“W”趋势, 从不同行政等级来看, 扩展速度的发展趋势具有一致性, 2000~2005年是浙江省不同行政等级的城市城镇用地扩展速度的最快阶段. (2)从扩展强度来看, 浙江省在2000~ 2005年对城镇用地扩展最大, 其他时期基本维持稳定. 地势平缓的城市往往开发强度大, 丘陵地区的城市处于缓慢扩展阶段. (3)浙江省城镇用地空间结构的分形维数和稳定性特征存在波动性. 城镇用地的空间结构特征与城镇用地增长过程和发展阶段具有一定的联系. (4)浙江省城镇用地重心受到地形限制明显. 西南地区受到丘陵地形影响, 重心移动方向大多数与斜长的峡谷平行; 北部平原区域的城镇用地的重心变化往往受到经济等社会因素影响较大. (5)浙江省城镇建设用地空间扩展的影响因素上存在一定规律, 可看出1995年、2010年、2015年主要倾向于社会经济的影响, 在2000年、2005年则倾向于自然因素的影响.     

无绝缘高温超导双饼线圈的瞬态电热特性分析

无绝缘高温超导线圈具有良好的电热稳定性和机械紧凑性,但其充电过程中却有明显的磁场延迟现象。为详细了解无绝缘高温超导线圈励磁过程的瞬态特性,建立了无绝缘高温超导线圈的同轴圆环等效电路模型。通过绕制一个670匝的无绝缘高温超导双饼线圈,在液氮温度下进行不同充电速率的励磁实验,初步验证了等效电路模型的正确性。基于该模型,针对线圈励磁过程的充电和恒流阶段,仿真得到了线圈各匝的径向电流分布规律和电热损耗特性。     

Influence of ultrasound on the functional characteristics of indigenous varieties of mango (Mangifera indica L.)

The present study was conducted to evaluate the effect of ultrasonic (US) treatment on chemical characteristics and antioxidant potential of pulps obtained from eight mango varieties indigenous to Pakistan. There was a significant (p < 0.05) effect of varieties and US treatment on chemical characteristics i.e. pH, acidity, TSS, vitamin C contents, total sugars (%), reducing sugars (%) and non-reducing sugars (%). Microstructure evaluation of pulp from all mango varieties showed deshaped middle lamella and cell wall of cells after 8 min of US treatment. At 4 min of US treatment as per shaped cell wall and middle lamella, the chemical characteristics and antioxidant potential were higher. The total phenolics (TP), flavonoids (TF) and total antioxidant activity (TAA) of pulp from most varieties increased significantly (p < 0.05) after US treatment for 4 min but decreased successively after each treatment i.e. 8 and 12 min. The maximum value (314.17 μg AAE/mL pulp) of DPPH was shown by pulp from Dosehri and the minimum (158.67 μg AAE/mL pulp) was found in pulp from Langra before US treatment. The DPPH values of pulp from most of the varieties increased significantly (p < 0.05) after US treatment for 4 min but decreased successively after each treatment but pulp from Langra showed increasing trend after 8 min of US treatment which decreased after 12 min of treatment. The total anthocyanin (TA) values of pulp from Chaunsa, Dosehri, Sindhri, Gulab Khas and Langra increased abruptly after US treatment for 4 min but decreased successively after subsequent treatment. The pulp from Desi, Anwar Ratol, Gulab Khas and Langra showed an abrupt decrease in TA after 8 min of US treatment. An increasing trend of values of total carotenoids (TC) was shown by pulp from all mango varieties after 4 min of US treatment but decreasing trend was observed with subsequent increase in time of US treatment.     

Damage characteristics and surface description of near-wall materials subjected to ultrasonic cavitation

For the analysis of ultrasonic cavitation erosion on the surface of materials, the ultrasonic cavitation erosion experiments for AlCu4Mg1 and Ti6Al4V were carried out, and the changes of surface topography, surface roughness, and Vickers hardness were explored. Cavitation pits gradually expand and deepen with the increase of experiment time, and Ti6Al4V is more difficult to erode by cavitation than AlCu4Mg1. After experiments, the cavitation damage characteristics such as the single pit, the rainbow ring area, the fisheye pit, and some small pits were observed, which can be considered to be induced by a single micro-jet impact, ablation effect caused by the high temperature, micro-jet impingement with a sharp angle, and multibeam micro-jets coupling impact or negative pressure in the local area produced by micro-jet impact, respectively. The surface roughness and Vickers hardness of the material increase slowly after rapid growth at different points in time as the experiment time increases. With the increase of the ultrasonic amplitude, both of them first increase and then decrease after the ultrasonic amplitude is greater than 10.8 μm. The increases in surface roughness and Vickers hardness tend to decrease as the viscosity coefficient increases. Ultrasonic cavitation can cause submicron surface roughness and increase surface hardness by 20.36%, so it can be used as a surface treatment method.     

Analysis in protein profile,antioxidant activity and structure-activity relationship based on ultrasound-assisted liquid-state fermentation of soybean meal with Bacillus subtilis

This study investigated effects of ultrasound on the contents of peptide and soluble protein, antioxidant activity, functionalities and structural characteristics of fermented soybean meal (FSBM) with Bacillus subtilis systematically. The results showed that there were significant effects of ultrasound treatments (frequency, treatment time and power density) on the contents of peptide and soluble protein (p < 0.05). Under the optimum ultrasound conditions (power density of 0.08 W/mL, frequency of 33 kHz and treatment time of 1 h) by single factor experiment, the contents of peptide and soluble protein increased by 31.27% and 18.79% compared to those of the control, respectively. Additionally, the in vitro antioxidant activity (•OH scavenging rate, Fe²⁺ chelating capacity and DPPH radical scavenging rate) and functional properties (emulsifying activity and emulsifying stability) of FSBM were found to be noticeably improved by ultrasound (p < 0.05). The fourier transform infrared (FTIR) spectroscopy revealed that ultrasound caused protein molecules to unfold with a decrease content of α-helix and β-turn and an increase in the proportion of β-sheet and random coil. Besides, atomic force microscope (AFM) results indicated that ultrasonication generally increased the surface roughness of protein and the protein sonicated with higher frequency (≥33 kHz) exhibited a greater height compared to lower frequency ultrasonication. Structure-activity relationship analysis illustrated that there was a good linear relationship between •OH scavenging rate and β-sheet/β-turn with Pearson’s correlation coefficient r of −0.86/0.90. Collectively, the selection of ultrasonic parameters is essential for the preparation of functional protein and bioactive peptide by enhancing fermentation of agroindustrial by-products.