Shock cooling of liquid nitrogen and superfluid helium

Abstract

Superfluid Helium (11) and liquid nitrogen are the only liquids which have been shown experimentally, to exhibit shock cooling. In the present paper we use the Landau model to demonstrate theoretically that the roton gap, which decreases with increasing density, plays the same role leading to shock cooling in liquid helium as the dissociation energy does in liquid nitrogen.     

Performance investigation of an advanced tracked prime mover on the low bearing soil

This study has presented a performance investigation of an advanced tracked prime mover for the operation of agricultural goods and other operations on peat terrain. The maximum and continuous traction torque of the prime mover has been developed by designing an advanced controller for controlling the intelligent system. The prime mover’s mobility is studied with ultrasonic displacement sensor, torque transducer, National Instrument cRIO-9004 Compact-RIO Real-time Controller Unit (RCU), a National Instrument TPC 2106T Touch Panel Control (TPC), a Trimble AG132 GPS antenna and receiver unit, and a Dlink DIR-655 router. The fuzzy logic controller (FLC) has been equipped with the prime mover hydraulic system to increase the traction torque of the hydraulic motor when the prime mover’s sinkage is more than or equal to 70 mm. The prime mover’s design demonstrates good potential in traversing peat terrain as the measured tractive effort was found to be 48% of the vehicle’s gross weight while the recommended tractive effort is in the range of 30–36% of the vehicle’s gross weight.     

真空冷却过程中实验条件对真空冷却速率的影响

以熟肉为实验材料,对实验条件对真空冷却速率的影响进行了理论分析和实验研究。实验结果表明:真空室有效容积越小、真空泵抽速越高,则真空冷却时间就会越短;冷阱温度对真空冷却速率有着明显的影响;当真空室内的最终压力在0.4～0.61kPa变化时,熟肉的表面温度一直在0℃以上,其真空冷却的时间随着真空室内压力的升高而增加。而真空室内的最终压力在0.3kPa左右时,熟肉的表面温度在真空冷却过程会低于0℃。     

Performance of a silicon monochromator under high heat load

The performance of a cryogenically cooled double‐crystal silicon monochromator was studied under high‐heat‐load conditions with total absorbed powers and power densities ranging from 8 to 780 W and from 8 to 240 W mm^?2, respectively. When the temperature of the first crystal is maintained close to the temperature of zero thermal expansion of silicon, the monochromator shows nearly ideal performance with a thermal slope error of 0.6 µrad. By tuning the size of the first slit, the regime of the ideal performance can be maintained over a wide range of heat loads, i.e. from power densities of 110 W mm^?2 (at total absorbed power of 510 W) to 240 W mm^?2 (at total absorbed power of 240 W).     

Condensed Mode Cooling of Ethylene Polymerization in Fluidized Bed Reactors

This review gives an overview of the evolution of the technology of condensed mode cooling, primarily for the case of ethylene polymerization on supported catalysts in fluidized bed reactors. It is well known that this mode of heat removal is quite effective in allowing polyolefin manufacturers to increase significantly production rates. What is perhaps less well understood are all of the issues that, in addition to the effect of the latent heat of vaporization of injected liquid components, also have an impact on the rate of production and behavior of the reactor. However, the liquid components injected into the reactor can vaporize rapidly under full‐scale conditions, leaving behind several heavy components (with respect to ethylene) that have numerous effects on how the particles behave, on the reaction rate, and on fluidization, fouling, and other parameters related to reactor and process performance.     

Research on the ions' axial temperature of a sympathetically-cooled 113Cd+ ion crystal

Molecular dynamics simulation of a sympathetically-cooled ¹¹³Cd⁺ ion crystal system is achieved. Moreover, the relationship between ions' axial temperature and different electric parameters, including radio frequency voltage and end-cap voltage is depicted. Under stable trapping condition, optimum radio frequency voltage, corresponding to minimum temperature and the highest cooling efficiency, is obtained. The temperature is positively correlated with end-cap voltage. The relationship is also confirmed by a sympathetically-cooled ¹¹³Cd⁺ microwave clock. The pseudo-potential model is used to illustrate the relationship and influence mechanism. A reasonable index, indicating ions' temperature, is proposed to quickly estimate the relative ions' temperature. The investigation is helpful for ion crystal investigation, such as spatial configuration manipulation, sympathetic cooling efficiency enhancement, and temporal evolution.     

Dependence of electronic and optical properties of multilayer SiC and GeC on stacking sequence and external electric field

The electronic and optical properties of different stacked multilayer SiC and GeC are investigated with and without external electric field (EEF). The band gaps of multilayer SiC and GeC are found smaller than that of monolayer SiC and GeC due to the interlayer coupling effect. When EEF is applied, the direct band gaps (ΔK–M) of multilayer SiC and direct band gaps (ΔK–K) of multilayer GeC all turn to indirect band gaps (ΔK–G) as the band at the G point drops dramatically toward zero. The imaginary part ε₂(ω)s of multilayer SiC and GeC show that new absorption peaks between 2–5 eV appear when the polarized direction is perpendicular to the layer plane, and new absorption peaks in infrared region appear as the EEF is higher than a certain point when the polarized direction is parallel to the layer plane. Our calculations reveal that different stacking sequences and EEF can provide a wide tunable band structures and optical properties for multilayer SiC and GeC.     

Modeling of the EHD effects on hydrodynamics and heat transfer within a flat miniature heat pipe including axial capillary grooves

A numerical model for an electrohydrodynamic (EHD) grooved Flat Miniature Heat Pipe (FMHP) is developed. Two microchannel shapes are considered as axial capillary structures: square and triangle grooves. For both groove shapes, the electric field affects the liquid-vapor radius of curvature which decreases in the condenser and increases in the evaporator under the action of the electric field. The liquid and vapor velocities are also affected by the EHD effects. The electric field effects on the velocities depend on the FMHP zone. It is also demonstrated that the electric field increases the vapor pressure drop; however, it decreases the liquid pressure drop. The liquid-wall and vapor-wall viscous forces as well as the shear liquid-vapor forces are affected by the electric field. The analysis of the electric forces shows that the dielectrophoretic forces which act on the liquid-vapor interface are predominant and their order of magnitude is much higher than the Coulomb forces. Finally, it is also demonstrated that the capillary limit increases with the electric field for both groove shapes.     

Dispersion Mechanism of Superfine SiC Particles in the Different Condition Liquid

SiC@A1(OH)₃-Y(OH)₃ core-shell composite particles are synthesized by co-precipitation method for strengthening the antioxidation of SiC at high temperature. To reach better A1(OH)₃-Y(OH)₃ composite shell and higher coating ratio on the SiC particles surfaces, SiC particles must be adequately dispersed in the SiC suspension during the coating process. The dispersion mechanism of SiC particles is investigated by the sedimentation method. Through test and analysis, the optimum conditions of the dispersion of SiC particles in the SiC suspension are sedimentating for 10 minutes, ultrasonic dispersion for 10 minutes, the lower SiC concentration, pH = 9, the dispersant content for the 2% volume of SiC suspension and using the polyelectrolyte dispersant, respectively.