Generation and measurement of sub-picosecond electron bunch in photocathode rf gun

We consider a scheme to generate a sub-picosecond electron bunch in the photocathode rf gun by im-proving the acceleration gradient in the gun, suitably tuning the bunch charge, the laser spot size and the acceleration phase, and reducing the growth of transverse emittance by laser shaping. A nondestructive technique is also reported to measure the electron bunch length, by measuring the high-frequency spectrum of wakefield radiation which is caused by the passage of a relativistic electron bunch through a channel surrounded by a dielectric.     

电子束激发原子对金属蒸发的影响

在原子蒸气激光同位素分离工程(AVLIS)中,金属受电子束的加热而熔化,并向真空蒸发,蒸气原子通过电子束的过程中,可能与电子发生非弹性碰撞,被激发到高能级.在膨胀的过程中,高能级的原子通过与原子的非弹性碰撞消激发,将原子内的电子能量转换为蒸气的平动能.为了分析电子束与原子作用对蒸气的密度、速度和温度等物理特性的影响,采样直接模拟蒙特卡罗法(DSMC)模拟钆原子蒸发过程.模拟结果表明,电子束与原子的作用使得原子蒸气的速度增加,密度减小,温度升高 关键词： 金属蒸发 AVLIS DSMC 电子枪     

提高偏滤器排灰效率和减少氚投料量的探讨

实验表明,通过抽气孔栏和偏滤顺可以排除聚变堆中的氦灰。在孔样和偏滤器靶板上中性化后未被立即抽出的部分α粒子,能被偏滤器等离子体再电离并回流到剖离区（ＳＯＬ）,甚至再进入等离子体芯部。探讨了在聚变实验增残堆ＦＥＢ－Ｅ偏滤器室内用ＲＦ场有质动力势来阻止这部分α粒子的回流。计算表明,用ＲＦ场有质动力势能将这部分再电离的Ｈｅ＾＋离子反射回靶板,同时不妨碍从芯部来的α粒子到达靶板,而且能阻止一部分氚离子进入     

Analysis About SASE Experiment on BFEL Facility

Investigation on SASE experimental demonstration on BFEL facility is presented in this paper. Both linear theory and simulation method are used in order to get useful results for guiding the future experiments. The requirements on electron beam and long wiggler are proposed and the possibility of realization is explored.     

北京大学国产大晶粒铌材超导腔的性能研究

大晶粒铌材是射频超导领域的研究热点之一. 采用大晶粒铌材的射频超导谐振腔, 其后处理工艺可以大大简化. 北京大学对此进行了深入细致的研究, 自主研制了采用国产大晶粒铌材的射频超导腔, 对这些超导腔进行了简单的表面处理, 包括标准的化学抛光(BCP)和120℃低温烘烤处理, 未进行非常复杂的电抛光处理, 低温性能测试结果表明其低温超导性能优越, 大晶粒1.3GHz超导腔的加速梯度达到了43.5MV/m, 为我国超导加速器的国产化打下了基础.     

Si／SiNx超晶格材料的非线性光学特性

采用射频磁控反应溅射技术与热退火处理制备了Si/SiNx超晶格材料。利用吸收光谱和X射线衍射对材料进行表征。通过皮秒脉冲激光单光束Z-扫描技术研究了该材料在非共振吸收区的三阶非线性光学特性,实验结果表明,样品的非线性折射率为负值,非线性吸收属于双光子吸收。由实验数据得到材料的三阶非线性极化率实部和虚部分别为1.27×10-7,1.51×10-8esu,该值比体硅材料的三阶非线性极化率值大5个数量级。对材料光学非线性产生的机理进行了探讨,认为材料的非线性极化率的增加来源于材料量子限制效应的增强。     

Noise-resilient multi-frequency surface sensor for nuclear quadrupole resonance

A planar nuclear quadrupole resonance (NQR) sensor has been developed. The sensor is resilient to environmental noise and is capable of simultaneous independent multi-frequency operation. The device was constructed as an open multimodal birdcage structure, in which the higher modes, generally not used in magnetic resonance, are utilized for NQR detection. These modes have smooth distributions of the amplitudes of the corresponding radiofrequency magnetic fields everywhere along the sensor’s surface. The phases of the fields, on the other hand, are cyclically shifted across the sensor’s surface. Noise signals coming from distant sources, therefore, induce equal-magnitude cyclically phase-shifted currents in different parts of the sensor. When such cyclically phase-shifted currents arrive at the mode connection point, they destructively interfere with each other and are cancelled out. NQR signals of polycrystalline or disordered substances, however, are efficiently detected by these modes because they are insensitive to the phases of the excitation/detection. No blind spots exist along the sensor’s surface. The sensor can be used for simultaneous detection of one or more substances in locations with environmental noise.     

Deposition and characterization of sputtered ZnO films

Zinc oxide thin films were deposited by radio frequency magnetron sputtering at room temperature using a metallic zinc target in a gas mixture of argon and oxygen. Plasma power, oxygen /argon gas ratio, gas pressure, and substrate temperature were varied, and an experimental design method was used to optimize these deposition parameters by considering their interdependence. Crystalline structures and film stresses were examined. Post-deposition rapid thermal annealing was also carried out to observe its effects on the film properties. Statistical analysis was then used to find the optimal sputtering conditions. Results indicated that plasma power and gas pressure have the largest effects on film crystallization and stress and that postdeposition annealing can be used to improve the quality of the film properties.     

Al3+对Ge/Al-SiO2薄膜光致发光的影响

采用磁控溅射及后退火技术制备了不同组份和不同退火温度的Ge、Al共掺SiO₂薄膜。通过对样品的X射线光电子能谱(XPS)测试,确定了薄膜的成分和结构特征;同时还测试了样品的光致发光谱(PL谱),得到了峰值位于420 nm附近的紫光发射峰和峰值位于470 nm的蓝光发射峰。实验结果表明, Al的掺杂不仅可以显著地提高GeNOV中心和SiNOV中心的光发射效率,还可以促进GeNOV缺陷和SiNOV缺陷中心的形成,进而有利于薄膜的光致发光。     

一种用于开放式MRI的射频发射线圈设计

介绍了一种用于开放式MRI系统的射频发射线圈. 此发射线圈为上下2个相同的线圈,分别安装在磁体的2极,两线圈采用非对称的正交方式放置. 线圈为矩形螺线管结构,通过电磁场数值计算的方法对线圈的匝间距进行了优化,使线圈在300 mm的球形区域内达到偏差不超过3 dB的均匀性要求. 根据优化结果制作了一套用于0.23 T开放式MRI系统的发射线圈,并对线圈的均匀性及射频发射的效率进行了测试. 测试结果表明,线圈具有较高的发射效率和较好的均匀性,由此验证了设计方案的可行性.