Investigation of the effects of 24 bio-matrices on the LC-MS/MS analysis of morinidazole

This study compares and evaluates the effect of various matrices on liquid chromatography (LC) coupled with tandem mass spectrometry (MS/MS) analysis. Permanent post-column infusion (PCI) was used to quantify matrix effects. In this way, the suppressed or enhanced signal of the target material resulting from different co-eluting matrix components could be assessed. Twenty-four biological samples from in vivo and in vitro experiments were selected for this study. In addition, 7 sample components were further analyzed after sample preparation by protein precipitation. Multiple regression analysis was used to investigate the collinear relationship between matrix effects and co-eluted components at different time intervals. We found that salt was the dominant factor which impacted changes in signal detection. In order to eliminate it, we used ammonium formate as a modifier of the mobile phase which resulted in charge-state redistribution profiles so that a homogeneous matrix formed. By employing pulse gradient chromatography in the presence of 5 mM ammonium formate, favorable improvements of enhanced signal intensity and reduced matrix effects were obtained. These experiments also indicated the feasibility of using analogue IS during bio-analysis which contributed to an overall faster assay that would be suitable for drug discovery and development purposes.     

同位镀铋膜电极测定爆米花中的痕量铅

采用同位镀铋膜法修饰铂电极,用差分脉冲溶出伏安法对爆米花中痕置铅进行了测定,并优化了实验条件.在优化的实验条件下,分别对2.0×10<'8>-6.0×10<'-7>mol/L和6.0×10<'-7>-1.0×10<'-4>mol/L的pb<'2+>进行了测定,Pb<'2+>溶出峰电流与Pb<'2+>浓度呈良好的线性关系...     

QCW diode-pumped 654 W AO Q-switched Nd:YAG rod oscillator-amplifier laser

A diode laser-pumped acoustic-optic Q-switched Nd:YAG master-oscillator power amplifier laser is presented. The laser is quasi continuously pumped at 1.1 kHz with a pulse width of 172 μs, and the ultrasonic frequency of the AO Q-switcher is set at a higher value (53 kHz). The master oscillator is designed as a thermally near-unstable-resonator, which presents an average output power of 48 W with a beam quality value of M² = 1.41 and a Q-switching pulse duration of 121 ns. The maximum average power of the MOPA system is 654 W, and the beam quality is M² = 6.     

Microstructure and surface mechanical properties of pulse electrodeposited nickel

The surface of carbon steel was modified by electrochemical deposition of Ni in a standard Watt's bath using dc and pulse plating electrodeposition. The aim was to compare the microstructure and surface mechanical properties of the deposit obtained by both techniques. Materials characterization was conducted using field emission scanning electron microscope fitted with scanning transmission electron detector, atomic force microscope and X-ray diffractometer. Nanoindentation hardness, elastic modulus, adhesion, coefficients of friction and wear rates were determined for both dc and pulse electrodeposits. Experimental results indicate that pulse electrodeposition produced finer Ni grains compared to dc plating. Size of Ni grains increased with deposition. Both dc and pulse deposition resulted in grain growth in preferred (2 0 0) orientation. However, presence of Ni (1 1 1) grains increased in deposits produced by pulse deposition. Pulse plated Ni exhibited higher hardness, creep and coefficient of friction and lower modulus of elasticity compared to dc plated Ni.     

A novel method for improving the adhesion strength of the electrodeposited Ni films in MEMS

Adhesion performance of MEMS materials is increasingly important with the widely use of miniaturized devices. This paper proposed a novel method for improving adhesion performance between electrodeposited Ni multi-layers. The new method is to treat the Ni substrate in nickel chloride plating solution by pulse reverse current technique before electrodeposition. The dense oxide film of Ni substrate can be removed effectively by this electrochemical method, meanwhile, the proper roughness of Ni substrate is in favor of epitaxial growth during electrodeposition. Moreover, the Ni film is electrodeposited by the new method with low stress and coarse crystal grain. Consequently, the adhesion performance of Ni films is improved dramatically. The experimental results show that the adhesion performance of Ni film electrodeposited by the new method is about 3 times that of by traditional method.     

Effect of the laser fluence on the surface characterization of β-FeSi2 films prepared by pulsed laser deposition

Single-phase β-FeSi₂ films on silicon (1 0 0) were fabricated by pulse laser deposition. The structure and crystal quality of the samples were characterized by X-ray diffraction and Fourier transform infrared spectroscopy. The field scanning electron microscopy showed that the film thickness increases with the increasing of the laser fluence. Moreover, atomic force microscopy observations revealed the changes of surface properties with different laser fluence. Based upon all experimental results, it is found that 7 J/cm² is the most favorable for the formation of β-FeSi₂ thin films.     

Assessment of pulmonary artery stiffness using velocity-encoding magnetic resonance imaging: evaluation of techniques

The loss of pulmonary artery (PA) compliance has significant pathophysiological effect on the right ventricle. Noninvasive and reliable assessment of PA wall stiffness would be an essential determiner of right heart load and a clinically useful factor to assess cardiovascular risk. Two MRI techniques have been proposed for assessing PA stiffness by measuring pulse wave velocity (PWV): transit time (TT) and flow area (QA). However, no data are available that compares the two techniques and evaluates their performance, especially over a wide range of PWV values or at 3.0-T, which is the purpose of the present study. Thirty-three patients with different heart conditions were imaged using optimized high-temporal resolution and high-spatial resolution velocity-encoding MRI sequences. Statistical analysis was conducted to study intermethod, interobserver and intraobserver variabilities. The PWV measurements using TT and QA techniques showed good agreement (P>0.1). The Bland-Altman analysis showed negligible differences between the two methods (mean±S.D.=0.11±0.35 m/s, correlation coefficient r=0.94). The repeated measurements showed low interobserver and intraobserver variabilities, although the S.D. of the differences was larger in the QA technique. The mean±S.D. of the TT/QA measurement differences were −0.05±0.2/0.0±0.36 m/s and 0.02±0.26/0.02±0.39 m/s for the interobserver and intraobserver differences, respectively. In conclusion, each technique has its own advantages and disadvantages. The two techniques result in similar measurements, although the QA method is more subjective due to its dependency on operator intervention.     

Elastodynamic analysis of a thin layer bonded on a visco-elastic medium under combined in-plane and lateral pulse loads

An analytic solution of a thin layer bonded on a visco-elastic medium under the action of in-plane and lateral pulse loads is presented. The analysis is based on double integral transforms with respect to space and time. Representative examples are studied and discussed to determine the influence of the (a) damping and elastic coefficients of visco-elastic medium, and (b) in-plane compression and stretching of the thin layer on wave propagation.