Determination of selenium, zinc and cadmium in antidandruff shampoos by atomic spectrometry after microwave assisted sample digestion

Microwave assisted pre-treatments for atomic spectrometric determination (inductive coupled plasma-optical emission spectrometry, ICP-OES or flame atomic absorption spectrometry, FAAS) of metallic elements, usually present in antidandruff shampoos, are proposed. They are based on the digestion of the sample with HNO₃ into a closed reactor, which is irradiated at 800 W for a few minutes. Selenium was determined by ICP-OES. The limit of detection was 0.11 mg l⁻¹; the relative standard deviation (R.S.D.) for the selenium content in the samples was in the 0.6–3.6% range. The results obtained were in agreement with the label contents and the recovery of the proposed method was in the 100–106% range. Zinc and cadmium were determined by FAAS. The limit of detection for zinc determination was 0.078 mg l⁻¹; the R.S.D. for zinc contents was in the 0.8–8.6% range. A limit of detection of 0.09 mg l⁻¹ was obtained for cadmium determination; the R.S.D. for cadmium contents was in the 0.7–2.7% range. The determinations were performed after two different sample mineralization pre-treatments — dry ashing (in an electric furnace) and wet mineralization (in a microwave oven). Both methodologies provided comparable results for zinc and cadmium determination in shampoos. The proposed microwave assisted digestion procedures allow a precise and accurate determination of selenium, zinc and cadmium in commercial antidandruff shampoos, and the sample pre-treatment is less time-consuming than the classic methods.     

Fermentation characteristics and the dynamic trend of chemical components during fermentation of Massa Medicata Fermentata

As a representative of traditionally fermented Chinese medicine, Massa Medicata Fermentata (MMF) shows the functions of invigorating the spleen and stomach and promoting digestion, which plays an important role in the treatment of gastrointestinal diseases. The fermentation mechanism and the key factors that affect the quality of MMF have not been revealed yet, which has become an urgent issue that limits its clinical application. This article aims to systematically and comprehensively reveal the transformation of physical properties and the dynamic trend of chemical components including substrate components, volatile components, and lactic acid as anaerobic fermentation product during MMF fermentation. Along with obvious hyphae growth observed for MMF, the weight of MMF decreased, and the moisture and temperature increased. Through the quantified 14 components from substrate, ferulic acid increased from 45.53 ± 6.94 to 141.89 ± 78.40 μg/g, while glycosides and phenolic acids declined except caffeic acid. Also, within the 66 volatile components analyzed, alcohols and acids increased, while aldehydes and ketones decreased. Lactic acid was not detected in the fermentation substrate, but an apparent increase in lactic acid content was observed along with the increased fermentation days, resulting in 2.54 ± 0.15 mg/g on day 8. Based on the tested components, the fermentation process of MMF was discriminated into three distinct stages by principal component analysis, and an optimal fermentation time of four days was proposed. The results of this study will be of great significance to clarify the characteristics of fermentation and conduce to improving quality standards of MMF.     

Copper(II) tetrafluoroborate as a novel and highly efficient catalyst for Michael addition of mercaptans to α,β-unsaturated carbonyl compounds

Copper(II) tetrafluoroborate has been found to be a new and highly efficient catalyst for Michael addition of thiols to α,β-unsaturated carbonyl compounds under solvent-free conditions and in H₂O at room temperature. The reactions are very fast and are completed in 2 min to 1 h affording high yields. The rate of thiol addition was dependent on the steric hindrance at the β-carbon of the α,β-unsaturated carbonyl substrate. In the case of chalcones, the reactions are best carried out in MeOH as solvent.     

Structural evolution of (Ca0.35Sr0.65)TiO3 perovskite at high pressures

Lattice parameters of a synthetic powder sample of Ca_0.35Sr_0.65TiO₃ perovskite have been determined by the method of Le Bail refinement, using synchrotron X-ray diffraction patterns collected at pressures up to 15.5 GPa with a membrane-driven diamond anvil cell. At ambient conditions, diffraction data were consistent with the I4/mcm structure reported previously in the literature for the same composition. Diffraction data collected at high pressures were consistent with tetragonal (or, at least, pseudo-tetragonal) lattice geometry, and no evidence was found for the development of any of the orthorhombic structures identified in other studies of (Ca, Sr)TiO₃ perovskites. Additional weak reflections, which could not be accounted for by the normal I4/mcm perovskite structure, were detected in diffraction patterns collected at pressures of 0.9-2.5 GPa, and above ∼13.5 GPa, however. Small anomalies in the evolution of unit cell volume and tetragonal strain were observed near 3 GPa, coinciding approximately with breaks in slope with increasing pressure of bulk and shear moduli for a sample with the same composition which had previously been reported. The anomalies could be due either to new tetragonal↔tetragonal/pseudo-tetragonal phase transitions or to subtle changes in compression mechanism of the tetragonal perovskite structure.     

Effect of Chamber Gas Phase on Mobile Phase pH and on Separation Efficiency in TLC. A New Mode of Chromatography

A new variant of thin-layer chromatography (TLC), based on a gradual change of mobile phase acidity during elution, is proposed. The pH change occurs in the mobile phase moving along the TLC plate as a result of its contact with an acidic or a basic gas phase that replaces the initial mobile phase vapor in the TLC chamber. The potential of this approach has been demonstrated by using carbon dioxide and ammonia gases to improve the resolution of benzoic acids and aromatic amines on polyamide TLC plates.     

One-step synthesis of the chelate oxides of bis(trialkylantimony) by an oxidative method

The chelate oxides of bis(trimethylantimony) (Me₃SbL¹)₂O (i = 1 or 2, L¹-acetylacetonate, L² - trifluoroacetylacetonate) and bis(triethylantimony) (Et₃SbL¹)₂O have been obtained in 79–85% yields by a one-step oxidation of trialkylantimony withtertbutylhydroperoxide in the presence of -diketones in benzene at 20 °C.Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 1, pp. 154–155, January, 1995.This work was carried out with financial support from the Russian Foundation for Basic Research (Project No. 94-03-08846).     

A fast procedure to immobilize polyethylene glycols in glass capillary columns

Polyethylene glycols can be immobilized in glass capillary columns by a new procedure involving covering the glass walls with a layer of graphitized carbon black and by flowing a mixture of the stationary phase and dicumyl peroxide. After curing and conditioning the column is ready for use. Excellent performance is reported for Carbowax 20 M and high molecular weight glycols. For other glycols the immobilized layer is less stable and can be washed out.     

Superoxes,high temperature universal phases in (GC)2

Most of the common classes of organic compounds chromatograph normally on Superoxes. There is no tailing or adverse effect from excessively different activity different activity coefficients. Superoxes are therefore universal phases for gas chromatography. This is also expressed by a wide useful temperature range from ～50° to ～300°. High MW Superox-4 has a MAOT about 20° higher than the lower MW Superox-0.1. Several applications illustrating the versatility of Superox phases in (GC)² are presented.     

Photocatalytic and antifouling properties of TiO2-based photocatalytic membranes

Photocatalysis has been extensively studied due to its potential ability to avoid the excessive use of chemical reagents and reduce the energy consumption by employing solar energy. Moreover, to alleviate the reduction in the membrane permeation selectivity, separation efficiency, and membrane service life caused by the emerging micro-pollutants and membrane fouling, membrane technology is often coupled with microbial, electrochemical, and catalytic processes. However, although physical/chemical cleaning and membrane module replacement can overcome the inherent limitations caused by membrane fouling and other membrane separation processes, high operating costs limit their practical applications. In this review, common preparation methods for TiO₂ photocatalytic membranes are described in detail, and the main approaches to enhancing their photocatalytic performance are discussed. More importantly, the mechanism of the TiO₂ photocatalytic membrane antifouling process is elucidated, and some applications of photocatalytic membranes in other areas are described. This review systematically outlines future research directions in the field of photocatalytic membrane modification, including metal and non-metal doping, fabrication of heterojunction structures, control over reaction conditions, increase in hydrophilicity, and increase in membrane porosity.     

Synthesis of New Ligand 1,2-Bis{di[（R,R）-1,3,2-oxzaphosphlidine]phosphino}ethane with C_2-symmetric Axis and Application in Rh-catalyzed Asymmetric Hydrogenation

New ligand 1,2-bis{di[（R,R）-1,3,2-oxzaphosphlidine]phosphino}ethane [（R,R）-BDOPPEs 1,2,3 and 4] with C2-symmetric axis and bearing nitrogen and oxygen were synthesized from readily available optically active amino alcohols.Rh complexes with these ligands were highly enantioselective catalysts for asymmetric hydrogenation of N-benzoyldehydroamino acid derivatives and α-functionalized ketones in 99%e.e.and 98%e.e.,respectively.This new class of（R,R）-BDOPPEs 1,2,3 and 4 gave much more effectivity and enantionselectivity than their corresponding non-C2-asymmetric aminophosphine phosphinite.