Structural studies of Cr-doped mullite derived from single-phase precursors

Cr-doped mullites were prepared from single-phase precursors containing up to 9.60 wt% Cr₂O₃ using a sol-gel technique followed by thermal treatment. Particle induced X-ray emission spectroscopy and X-ray powder diffraction were used to characterize the samples. Mullites were orthorhombic, space group Pbam. Cr doping caused the increase of unit-cell parameters. Strongest expansion was noticed along c-axis followed by a and b (Δc/c=0.089, Δa/a=0.061, Δb/b=0.045% per mole Cr₂O₃). A second phase, namely θ-(Al,Cr)₂O₃, was revealed by XRD in the sample containing 9.60 wt% Cr₂O₃. The structure of mullites was refined by the Rietveld method, location of Cr³⁺ was performed by the EPR spectroscopy. At low chromium doping level (Cr₂O₃ content less than ∼5 wt%) Cr³⁺ ions were substituted for Al³⁺ in the AlO₆ octahedra of the mullite structure (M1 site). For higher doping level, Cr³⁺ ions were additionally substituted for Al³⁺ in the AlO₆ octahedra of the second phase [θ-(Al,Cr)₂O₃ at 1400 °C, or α-(Al,Cr)₂O₃ at 1600 °C] which segregated in the system. Substitution of Cr³⁺ for Al³⁺ on M1 site in the mullite structure resulted in increase of average distances in (M1)O₆ octahedron and decrease of average distances in T*O₄ tetrahedron, while average distances in TO₄ tetrahedron stayed almost constant.     

Study of nitrogen ion implantation and diffusion phenomena on thin chromium layers followed by the atomic force microscopy and secondary ion mass spectroscopy techniques characterization

This research investigates the effect of ion implantation dosage level and further thermal treatment on the physical characteristics of chromium coatings on Si(1 1 1) substrates. Chromium films had been exposed to nitrogen ion fluencies of 1 × 10¹⁷, 3 × 10¹⁷, 6 × 10¹⁷ and 10 × 10¹⁷ N⁺ cm⁻² with a 15 keV energy level. Obtained samples had been heat treated at 450 °C at a pressure of 2 × 10⁻² Torr in an argon atmosphere for 30 h. Atomic force microscopy (AFM) images showed significant increase in surface roughness as a result of nitrogen ion fluence increase. Secondary ion mass spectroscopy (SIMS) studies revealed a clear increased accumulation of Cr₂N phase near the surface as a result of higher N⁺ fluence. XRD patterns showed preferred growth of [0 0 2] and [1 1 1] planes of Cr₂N phase as a result of higher ion implantation fluence. These results had been explained based on the nucleation-growth of Cr₂N phase and nitrogen atoms diffusion history during the thermal treatment process.     

无催化纳米氧化锌的制备及其光学性质研究

本文采用无催化剂直接蒸发高纯Zn粉,在800℃氧气氛条件下,在Si(111)衬底上生长得到以四角状为主的纳米ZnO(T-ZnO)。T-ZnO纳米线每个角约互成110°,长度约为1.5μm,直径100nm左右;Raman分析表明E2(H)普遍存在于各形态的ZnO;光致发光光谱表明,T-ZnO纳米线的光致发光除了与材料性质有关,还与杂质缺陷有关,蓝绿光带是ZnO的缺陷产生的。     

傅里叶变换红外光谱与拉曼光谱分析碳青霉烯药物亚胺培南的结构特征

本文采用傅里叶变换红外光谱和激光拉曼光谱对碳青霉烯药物亚胺培南进行光谱检测,并对其的分子振动光谱与结构特征进行分析和探讨,分析了亚胺培南在固相状态下的结构形式,从而为药物合成及质量控制提供了重要的参考价值。     

Holographic interferometry as electrochemical emission spectroscopy of a carbon steel in 5–20 ppm TROS C-70 inhibited seawater

In the present investigation, holographic interferometry was utilized for the first time to determine the rate change of the number of the fringe evolutions during the corrosion test of a carbon steel in blank seawater and seawater with different concentrations of a corrosion inhibitor. In other words, the anodic dissolution behaviors (corrosion) of the carbon steel were determined simultaneously by holographic interferometry, as an electromagnetic method, and by the electrochemical impedance (EI) spectroscopy, as an electronic method. So, the abrupt rate change of the number of the fringe evolutions during corrosion tests, EI spectroscopy, of the carbon steel is called electrochemical emission spectroscopy. The corrosion process of the steel samples was carried out in blank seawater and seawater with different concentrations, 5–20 ppm, of TROS C-70 corrosion inhibitor using the EI spectroscopy method, at room temperature. The electrochemical-emission spectra of the carbon steel in different solutions represent a detailed picture of the rate change of the anodic dissolution of the steel throughout the corrosion processes. Furthermore, the optical interferometry data of the carbon steel were compared to the data, which was obtained from the EI. spectroscopy. Consequently, holographic interferometry is found very useful for monitoring the anodic dissolution behaviors of metals, in which the number of the fringe evolutions of the steel samples can be determined in situ.     

Structural and lithium intercalation studies of Mn(0.5−x)CaxTi2(PO4)3 phases (0≤x≤0.50)

Materials from the Mn_(0.5−x)Ca_xTi₂(PO₄)₃ (0≤x≤0.50) solid solution were obtained by solid-state reaction in air at 1000 °C. Selected compositions were investigated by powder X-ray diffraction analysis, ³¹P nuclear magnetic resonance (NMR) spectroscopy and electrochemical lithium intercalation. The structure of all samples determined by Rietveld analysis is of the Nasicon type with the R space group. Mn²⁺/Ca²⁺ ions occupy only the M1 sites in the Ti₂(PO₄)₃ framework. The divalent cations are ordered in one of two M1 sites, except for the Mn_0.50Ti₂(PO₄)₃ phase, where a small departure from the ideal order is observed by XRD and ³¹P MAS NMR. The electrochemical behaviour of Mn_0.50Ti₂(PO₄)₃ and Mn_(0.5−x)Ca_xTi₂(PO₄)₃ phases was characterised in Li cells. Two Li ions can be inserted without altering the Ti₂(PO₄)₃ framework. In the 0≤y≤2 range, the OCV curves of Li//Li_yMn_0.50Ti₂(PO₄)₃ cells show two main potential plateaus at 2.90 and 2.50–2.30 V. Comparison between the OCV curves of Li//Li_(1+y)Ti₂(PO₄)₃ and Li//Li_yMn_0.50Ti₂(PO₄)₃ shows that the intercalation occurs first in the unoccupied M1 site of Mn_0.50Ti₂(PO₄)₃ at 2.90 V and then, for compositions y>0.50, at the M2 site (2.50–2.30 V voltage range). The effect of calcium substitution in Mn_0.50Ti₂(PO₄)₃ on the lithium intercalation is also discussed from a structural and kinetic viewpoint. In all systems, the lithium intercalation is associated with a redistribution of the divalent cation over all M1 sites. In the case of Mn_0.50Ti₂(PO₄)₃, the stability of Mn²⁺ either in an octahedral or tetrahedral environment facilitates cationic migration.     

CO-laser photoacoustic detection of phosgene (COCl2)

Detection of COCl₂, a highly toxic gas in chemical industry, using laser photoacoustic spectroscopy is presented. The spectrophone system used has a broad band LN₂ cooled CW CO laser as a source of radiation, which operates from 4.8–8.4 um in the mid-infrared. Using an extracavity open longitudinal resonant cell, absorption signals to about 30 CO laser lines in the 5.45 um region could be observed. detection sensitivity has been estimated to be ppb order.This work has been supported by the NSFC     

Effects of UV photon irradiation on SiOx (0 < x < 2) structural properties

Thin films of a-SiO_x (0 < x < 2) were prepared by reactive r.f. magnetron sputtering from a polycrystalline-silicon target in an Ar/O₂ gas mixture. The oxygen partial pressure in the deposition chamber was varied so as to obtain films with different values of x. The plasma was monitored, during depositions, by optical emission spectroscopy (OES) system. Energy dispersive X-ray (EDX) measurements and infra-red (IR) spectroscopy were used to study the compositional and structural properties of the deposited layers.Structural modifications of SiO_x thin films have been induced by UV photons’ bombardment (wavelength of 248 nm) using a pulsed laser. IR spectroscopy and X-ray photoemission spectroscopy (XPS) were used to investigate the structural changes as a function of x value and incident energy. SiO_x phase separation by spinodal decomposition was revealed. The IR peak position shifted towards high wavenumber values when the laser energy is increased. Values corresponding to the SiO₂ material (only Si⁴⁺) have been found for laser irradiated samples, independently on the original x value. The phase separation process has a threshold energy that is in agreement with theoretical values calculated for the dissociation energy of the investigated material.For high values of the laser energy, crystalline silicon embedded in oxygen-rich silicon oxide was revealed by Raman spectroscopy.     

A Mössbauer spectroscopic study of an industrial catalyst for dehydrogenation of etylbenzene to styrene

Iron oxide catalyst with spinel structure used for dehydrogenation of ethylbenzene is one kind of important catalyst in petrochemical industry. In this work several series of industrial catalyst were prepared with different components and different manufacturing processes. Mössbauer Spectroscopy has been used to determine the optimal components and the better manufacturing process for spinel structure formation. The results may prove useful for producing the industrial dehydrogenation catalyst with better catalytic property.     

Amorphous Fe–Mg alloy thin films: magnetic properties and atomic vibrational dynamics

Amorphous (a-) Fe _x Mg_1?x alloys are interesting materials for the investigation of non-Debye-like low-energy vibrational excitations. We have prepared a-Fe _x Mg_1?x alloy thin films (0.3 ≤ × ≤0.7) by vapour quenching. The amorphous state was confirmed by conversion electron Mössbauer spectroscopy between 4.2–300 K, and the x- and temperature-dependence of the isomer shift and hyperfine magnetic field was measured. For x= 0.6 and 0.7, magnetic ordering occurs below ~150 K. The atomic vibrational density of states, g(E), was determined by nuclear resonant inelastic scattering, providing clear evidence for the non-Debye-like low-energy vibrational excitations.