CRYSTAL STRUCTURE AND MORPHOLOGY OF NASCENT SAMPLES OF SYMMETRIC AROMATIC POLYESTERS——Ⅱ. POLY(p-PHENYLENE 2,6-NAPHTHALATE)

Confined thin film melt polymerization (CTFMP) of naphthalene chloride/hydroquinone (NCMQ, 1/1, molar)mixtures at polymerization temperatures (T_p) below ca. 300℃ resulted in relatively thick, elongated crystals. Polymerizationof NC/HQ above 300℃ between glass yielded well-formed lamellar crystals ca. 100 A thick. Phase Ⅰ and Ⅱ [001] EDpatterns were obtained for all T_p, the relative amount of phase Ⅰ increasing with T_p. Polymerization of naphthalenedicarboxylic acid/hydroquinione diacetate 1/1 mixtures at high T_p also yielded lamellar crystals that "curled up" off of thesubstrate. When the high temperature CTFMP polymerization was conducted between mica, aggregates of lamellae on-edgedeveloped but epitaxial growth did not occur. Epitaxial growth of lamellae between mica could be obtained, however, byconfined thin film solution polymerization, with both of the latter samples yielding apparently related ED patterns from adifferent unit cell than phase Ⅰ or Ⅱ. Fiber patterns, obtained from sheared samples, indicated considerably greater crystaldisorder than in the nascent crystals. Refinement of the phase Ⅰ unit cell parameters, based on the [001] and [01 1] EDpatterns, with modeling based on Cerius~2, suggests a monoclinic phase Ⅰ unit cell with a = 7.76, b = 5.71, c = 14.99 A, α = γ= 90°, β= 99.7°, ρ = 1.47 g/cm~3, space group P12_1/al.     

Flame Temperature Effect on the Structure of SiC Nanoparticles Grown by Laser Pyrolysis

Small SiC nanoparticles (10 nm diameter) have been grown in a flow reactor by CO₂ laser pyrolysis from a C₂H₂ and SiH₄ mixture. The laser radiation is strongly absorbed by SiH₄ vibration. The energy is transferred to the reactive medium and leads to the dissociation of molecules and the subsequent growth of the nanoparticles. The reaction happens with a flame. The purpose of the experiments reported in this paper is to limit the size of the growing particles to the nanometric scale for which specific properties are expected to appear. Therefore the effects of experimental parameters on the structure and chemical composition of nanoparticles have been investigated. For a given reactive mixture and gas velocity, the flame temperature is governed by the laser power. In this study, the temperature was varied from 875°C to 1100°C. The chemical analysis of the products indicate that their composition is a function of the temperature. For the same C/Si atomic ratio in the gaseous phase, the C/Si ratio in the powder increases from 0.7 at 875°C up to 1.02 at 1100°C, indicating a growth mechanism limited by C₂H₂ dissociation. As expected, X-ray diffraction has shown an improved crystallisation with increasing temperature. Transmission electron microscopy observations have revealed the formation of 10 nm grains for all values of laser power (or flame temperature). These grains appear amorphous at low temperature, whereas they contain an increasing number of nanocrystals (2 nm diameter) when the temperature increases. These results pave the way to a better control of the structure and chemical composition of laser synthesised SiC nanoparticles in the 10 nm range.     

111In–L–LDL and 153Gd–L–LDL as radiotracers for detection of AR4‐2J rat pancreatic tumors

Pancreatic cancer has an extremely poor prognosis, due, in part, to lack of methods for early diagnosis. The present study was designed to evaluate the potential of labeling low‐density lipoprotein (LDL) with a radionuclide using a lipid chelating agent, bis(stearylamide) of diethylenetriaminepentaacetic acid (L), to detect pancreatic tumors by gamma‐scintigraphy. Previous studies indicated that the difficulty of visualization of pancreatic tumors was due to their poor vascularization. This study compares the ability of two radiotracers, ¹¹¹In–L–LDL and ¹⁵³Gd–L–LDL to target highly vascularized rat pancreatic tumors (AR4‐2J) implanted in nude mice. Biodistribution studies showed that the tumor uptake of ¹¹¹In–L–LDL and ¹⁵³Gd–L–LDL tracers was twofold and fivefold higher respectively than with the controls (¹¹¹In citrate and ¹⁵³Gd citrate respectively). These tracers would thus be suitable for scintigraphic imaging. We show here that LDL could be employed as a delivery system for tracers such as ¹¹¹In or ¹⁵³Gd when these two radionuclides are complexed by a lipid‐chelating anchor, and that ¹¹¹In–L–LDL and ¹⁵³Gd–L–LDL enabled better visualization of the pancreatic tumor tissues, with a better result with ¹⁵³Gd–L–LDL. Copyright © 2004 John Wiley & Sons, Ltd.     

Formation of β‐iPP in isotactic polypropylene/ethylene–propylene rubber blends: Effects of preparation method,composition, and thermal condition

The effects of preparation method, composition, and thermal condition on formation of β‐iPP in isotactic polypropylene/ethylene–propylene rubber (iPP/EPR) blends were studied using modulated differential scanning calorimeter (MDSC), wide angle X‐ray diffraction (WAXD), and phase contrast microscopy (PCM). It was found that the α‐iPP and β‐iPP can simultaneity form in the melt‐blended samples, whereas only α‐iPP exists in the solution‐blended samples. The results show that the formation of β‐iPP in the melt‐blended samples is related to the crystallization temperature and the β‐iPP generally diminishes and finally vanishes when the crystallization temperature moves far from 125 °C. The phenomena that the lower critical temperature of β‐iPP in iPP/EPR obviously increases to 114 °C and the upper critical temperature decreases to 134 °C indicate the narrowing of temperature interval, facilitating the formation of β‐iPP in iPP/EPR. Furthermore, it was found that the amount of β‐iPP in melt‐blended iPP/EPR samples is dependent on the composition and the maximum amount of β‐iPP formed when the composition of iPP/EPR blends is 85:15 in weight. The results through examining the effect of annealing for iPP/EPR samples at melt state indicate that this annealing may eliminate the susceptibility to β‐crystallization of iPP. However, only α‐iPP can be observed in solution‐blended samples subjected to annealing for different time. The PCM images demonstrate that an obvious phase‐separation happens in both melt‐blended and solution‐blended iPP/EPR samples, implying that compared with the disperse degree of EPR in iPP, the preparation method plays a dominant role in formation of β‐iPP. It is suggested that the origin of formation of β‐iPP results from the thermomechanical history of the EPR component in iPP/EPR. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1704–1712, 2007     

Synthesis, morphology and random laser action of ZnO nanostructures

Three-dimensional (3-D) ZnO random-wall nanostructures and one-dimensional (1-D) ZnO nanorods were prepared on silicon substrates by a simple solid-vapour phase thermal sublimation technique. Optical pumped random lasing has been observed in the ZnO random-wall arrays with a threshold intensity of 0.38 MW/cm² in the emission wavelength from 380 to 395 nm. The optical gain was attributed to the closed-loop scattering and light amplification of the ZnO random-wall. The experimental result suggests that the morphology of nanostructure is the key factor to effect random lasing.     

Novel applications of 2-cyanoethylanilines in the synthesis of conjugated primary and secondary anilines

2-Cyanoethyl anilines were controllably cleaved by 1 equiv of potassium t-butoxide in dry THF with a reaction that can be used in situ with the Wittig reaction to synthesize conjugated primary and secondary anilines.     

The synthesis mechanism of Ca3Al2O6 from soft mechanochemically activated precursors studied by time-resolved neutron diffraction up to 1000°C

The reaction pathway for the Ca₃Al₂O₆ formation up to 1300°C, from mechanochemically treated mixtures of amorphous aluminum hydroxide and CaCO₃, was studied in situ by differential thermal analysis, constant heating rate dilatometry and time-resolved neutron powder diffraction. The experiment was carried out, in an open system, on a sample with the nominal Ca₃Al₂O₆ stoichiometry. The results obtained by neutron diffractometry and thermal analysis were in good agreement with the data obtained by scanning electron microscopy and X-ray diffraction on heat-treated and-quenched samples. The synthesis path implied the formation of cryptocrystalline Al₂O₃, crystalline CaO, CaAl₂O₄ and Ca₁₂Al₁₄O₃₃ as transitory phases. Finally the nucleation and growth of the single phase Ca₃Al₂O₆ took place at 1300°C and exhibited porous structure due to CO₂ and H₂O release.     

Synthesis and characterization of a novel nano-scale magnetic solid base catalyst involving a layered double hydroxide supported on a ferrite core

A nano-scale magnetic solid base catalyst MgAl-OH-LDH/MgFe₂O₄ (where LDH denotes layered double hydroxide) composed of MgAl-OH-LDH Brønsted base catalytic layers coated on MgFe₂O₄ spinel cores has been prepared. A magnetic precursor MgAl-CO₃-LDH/MgFe₂O₄ was prepared by a method involving separate nucleation and aging steps, and subsequently calcined to give a mixed metal oxide composite MgAl(O)/MgFe₂O₄ which was rehydrated to give MgAl-OH-LDH/MgFe₂O₄. The structure and magnetic properties of the nano-scale magnetic solid base MgAl-OH-LDH/MgFe₂O₄, together with those of the magnetic precursor MgAl-CO₃-LDH/MgFe₂O₄ and MgFe₂O₄ were characterized by XRD, XPS, low temperature N₂ adsorption and vibrating sample magnetometry (VSM). The MgAl-OH-LDH/MgFe₂O₄ composite possesses a mesoporous structure with pore size ranging from 2 to 20 nm with particle size mainly in the range 35-130 nm. The catalytic properties of MgAl-OH-LDH/MgFe₂O₄ were evaluated using the self-condensation of acetone at 273 K as a probe reaction. The results showed that the conversion of acetone to diacetone alcohol reached the thermodynamic equilibrium value of 23% at 273 K. The catalyst was easily recovered through application of an external magnetic field, and when the reclaimed catalyst was used in a second run for the same reaction, the reactivity remained unchanged.     

A DC excited waveguide multibeam CO2 laser using high frequency pre-ionization technique

High power industrial multibeam CO₂ lasers consist of a large number of closely packed parallel glass discharge tubes sharing a common plane parallel resonator. Every discharge tube forms an independent resonator. When discharge tubes of smaller diameter are used and the Fresnel numberN ≪ 1 for all resonators, they operate in waveguide mode. Waveguide modes have excellent discrimination of higher order modes. A DC excited waveguide multibeam CO₂ laser is reported having six glass discharge tubes. Simultaneous excitation of DC discharge in all sections is achieved by producing pre-ionization using an auxiliary high frequency pulsed discharge along with its other advantages. Maximum 170 W output power is obtained with all beams operating in EH₁₁ waveguide mode. The specific power of 28 W/m is much higher as compared to similar AC excited waveguide multibeam CO₂ lasers. Theoretical analysis shows that all resonators of this laser will support only EH₁₁ mode. This laser is successfully used for woodcutting     

Cu-MgF2复合纳米金属陶瓷薄膜的电导特性研究

用射频磁控共溅射法制备了Cu体积分数分别为 10 % ,15 % ,2 0 %和 3 0 %的Cu MgF2 复合金属陶瓷薄膜 .用x射线衍射、x射线光电子能谱和变温四引线技术对薄膜的微结构、组分及电导特性进行了测试分析 .微结构分析表明 :制备的Cu MgF2 复合薄膜由fcc Cu晶态纳米微粒镶嵌于主要为非晶态的MgF2 陶瓷基体中构成 ,Cu晶粒的平均晶粒尺寸随组分增加从 11 9nm增至 17 8nm .5 0— 3 0 0K温度范围内的电导测试结果表明 :当Cu体积分数qM 由 15 %增加到 2 0 %时 ,Cu MgF2 复合薄膜的电阻减小了 8个量级 ,得出制备的复合薄膜渗透阈qCM 应处于 15 %和 2 0 %之间 .qM 在 10 %和 15 %之间的薄膜呈介质导电状态 ,而在 2 0 %和 3 0 %之间的薄膜则呈金属导电状态 .从理论上讨论了复合薄膜中杂质电导和本征电导的激活能及其对电导的贡献 ,并讨论了Cu MgF2 复合纳米金属陶瓷薄膜的渗透阈 ,得到了和实验一致的结果