压电晶体位移特性曲线干涉自动测量方法

本文提出了压电晶体(PZT)位移物曲线自动干涉测量方法,该方法利用干涉仪把PZT的微位移量转化成干涉条纹相位变化量,通过快速傅里叶变换(FFT)方法自动复原干涉条纹中包含的相位的变化量,从而高精度地检测出PZT的位移特性曲线.根据该方法,利用CCD摄象机、图象板和干涉仪组合成一套光、机、电一体化的微位移自动测试系统,实际测量了我们研制的PZT随电压变化的位移特性曲线.实验表明,该方法原理实现简单,且能实现高精度、自动、实时和动态测量.     

Synthesis and characterization of an azobenzene‐ and acrylamide‐based photoresponsive copolymer and gel

This article reports the synthesis and characterization of a new type of copolymer consisting of acrylamide and trans‐4‐methacroyloxyazobenzene and their gel. Free‐radical polymerization initiated with 2,2′‐azobisisobutyronitrile was used to conduct the synthesis although N,N′‐methylene bisacrylamide was used as a crosslinking agent for the gel synthesis. Despite the insolubility of the different monomers in a single solvent, a certain ratio of water/tetrahydrofuran (THF) enabled the propagating species to stay in the solution and thus to facilitate chain growth. The solubility, Fourier transform infrared spectra, and solid‐state ¹³C NMR investigations revealed that two monomers in the copolymer were chemically bonded. The compositions of the incorporated acrylamide and azobenzene in the copolymer and the gel were determined by NMR spectroscopy. Because the potential actuating behavior of such materials was due to the volume change involved in reversible solvent uptake, the sorption and evaporation of the gel were also investigated and showed that the gel could absorb about 460% water, which corresponded to a polymer content of the weight gel of 18% and was compatible with thermogravimetric analysis of a saturated gel that revealed about 83 wt % of a swollen gel was lost within 12 h. Finally, photoinduced trans–cis isomerization kinetics of the copolymer was investigated in a 30:70 mixture of water and THF against irradiation time. A photostationary state was reached within 5.5 min with a corresponding conversion of 70% of the trans isomer to the cis form. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2886–2896, 2004     

Determination of piezoelectric coefficients of ferroelectric thin films using GaAs:Cr adaptive interferometer

We report on simple interferometric technique for the measurement of piezoelectric coefficients of thin films using GaAs:Cr adaptive photodetectors in the geometry of modified Mach–Zehnder interferometer. The technique needs no special vibroinsulation and automatically adjusts and keeps the operation point of the interferometer. Strong hysteresis effects with a slightly asymmetric form of the hysteresis loop were observed at the dependence of d₃₃ coefficients of the Pb(Zr,Ti)O₃ (PZT) thin film versus DC electric field. The obtained values of d₃₃ coefficients are in agreement with known data.     

Sol-Gel Synthesis of Nanocrystalline PZT Using a Novel System

A simple system has been developed for the preparation of lead zirconate titanate, Pb(Zr _x Ti_{1 – x} )O₃ powders by sol-gel process. To achieve stable and homogeneous precursor solutions, chelating ligands such as acetic acid and acetylacetone have been used for the chemical modification of titanium and zirconium starting precursors. Phase-pure PZT powders were obtained, through a pyrochlore-free pathway, from the amorphous xerogel after heat treatment at 600°C. The formation of the crystalline phase, compositional homogeneity, sinterability, dielectric and piezoelectric characteristics of PZT are reported.     

溶剂型智能驱动材料的研究进展

智能驱动材料可对光、电、温度、溶剂、湿度等外界刺激做出可控的力学响应,并将这些能量转化为机械能而被广泛关注.溶剂型驱动材料是基于简单的湿度或溶剂气氛变化将化学能转换成机械能,并在机械发电、微型器件制备等方面具有重要的潜在应用.本文综述了溶剂型智能驱动材料的驱动类型、驱动原理,性能及其相关应用进展,并对溶剂型智能驱动材料在未来人工智能方面的应用前景进行了展望.     

Powderless processing of ceramics: Thin-layer electroceramics

A review is made of progress on the sol-gel processing of dense insulating electroceramics by polymeric condensation routes. Up until the past ten years, powders and porous coatings were principally made for optical and conductive applications. Much effort was expended on silica (SiO₂) and silicate-based systems. Recently, these approaches have been extended to non-silicate systems [1]. In this paper information is presented for the powderless processing of selected electroceramics in thin-layer form. Materials include PbTiO₃, BaTiO₃, Ba_1–x Pb _x TiO₃, PbZrO₃, Pb(Zr_1–y Ti _y )O₃ and (Pb_1–x La _x )(Zr_1–y Ti _y )O₃ which find applications in ceramic capacitors, piezoelectric transducers and electrooptic modulators. The approach is to avoid powders, and the attendent problems of powder handling, flow, packing, etc., and make use of polymerization condensation reactions to form extended networks with chemical linkage. Data are reported for the synthesis and low temperature processing routes for amorphous and polycrystalline ceramics.     

Lead Zirconate-Titanate Films Prepared from Soluble Powders

Precursor powders for Pb(Zr1 – xTix) O3 (PZT) thin films were produced by the reaction of zirconium-and titanium-n-propoxides with acetylacetone and lead acetate trihydrate. The subsequent complete removal of volatile components yielded powders that can be handled in air. The powders are indefinitely stable under ambient conditions.High molarity (>2m) coating sols were prepared by dissolution of the precursor powders in mixtures of 1,3-propanediol, triethanolamine (TEA) and water. Excess amounts of lead to compensate lead loss during firing were easily introduced into these solutions.The deposition of these sols on steel substrates and firing at 600°C yielded PZT films. Many physical parameters like film thickness, morphology and electrical performance could be influenced by choice of the solvent mixture composition and oxide content of the sols. Depending on the preparation dielectric permittivities, r of up to 840 were measured at 1 kHz. By hysteresis measurements at 50 Hz and a field amplitude of 50 V/m a remanent polarization of about 40 C/cm2 and coercivity of about 8 V/m was obtained. The films were stable against dielectric breakdown up to 70V/m.     

Experimental and computational study of the flow induced by a plasma actuator

A complementary experimental and computational study of the flow field evoked by a plasma actuator mounted on a flat plate was in focus of the present work. The main objective of the experimental investigation was the determination of the vector force imparted by the plasma actuator to the fluid flow. The force distribution was presently extracted from the Navier–Stokes equations directly by feeding them with the velocity field measured by a PIV technique. Assuming a steady-in-mean, two-dimensional flow with zero-pressure gradient, the imbalance between the convective term and the momentum equation’s right-hand-side terms reveals the desired resulting force. This force-distribution database was used afterwards as the source term in the momentum equation. Furthermore, an empirical model formulation for the volume-force determination parameterized by the underlying PIV-based model is derived. The model is tested within the RANS framework in order to predict a wall jet-like flow induced by a plasma actuator. The Reynolds equations are closed by a near-wall second-moment closure model based on the homogeneous dissipation rate of the kinetic energy of turbulence. The computationally obtained velocity field is analysed along with the experimental data focussing on the wall jet flow region in proximity of the plasma actuator. For comparison purposes, different existing phenomenological models were applied to evaluate the new model’s accuracy. The comparative analysis of all applied models demonstrates the strength of the new empirical model, particularly within the plasma domain. In addition, the presently formulated empirical model was applied to the flow in a three-dimensional diffuser whose inflow was modulated by a pair of streamwise vortices generated by the present plasma actuator. The direct comparison with existing experimental data of Grundmann et al. (2011) demonstrated that the specific decrease of the diffuser pressure corresponding to the continuous forcing was predicted correctly.     

电极对PZT铁电薄膜的铁电和光学性能的影响

采用射频磁控溅射(RF Magnetron Sputtering)工艺在Si片上分别制备Pt/Ti和LaNiO3 (LNO)底电极,然后在不同的底电极上沉积PbZr0.52Ti0.48O3(PZT)铁电薄膜,在大气环境中对沉积的PZT薄膜进行快速热退火处理(RTA).用X射线衍射(XRD)分析PZT薄膜的相结构和结晶取向,原子力显微镜(AFM)分析薄膜的表面形貌和微结构.再沉积LNO作为顶电极制成"三明治"结构的LNO/PZT/Pt和LNO/PZT/LNO样品,用 RT66A标准铁电测试系统分析样品的电学特性,傅立叶红外光谱仪分别测得样品的反射谱和透射谱.分析了不同电极对PZT铁电薄膜的铁电和光学性能的影响.     

Using a thin actuator as secondary source for hybrid passive/active absorption in an impedance tube

This paper describes the practical implementation of a piezoelectric actuator as secondary source for hybrid passive/active broadband sound absorption in a standing-wave tube. This actuator consists of a thin circular aluminium plate driven by a piezoelectric patch and glued to a flexible rubber support. The resulting device has been mounted in a thin metallic ring that fits perfectly to the tube diameter. Passive absorption is afforded by either a porous layer or a microperforated panel, backed by an air gap. Active absorption is accomplished by releasing the sound pressure at a microphone behind the material, using either a loudspeaker or the actuator as secondary source. Results of broadband sound absorption reveal the feasibility of the piezoactuator. Compared to the loudspeaker, this actuator allows to greatly reduce the whole thickness of the hybrid absorber.