具有鲁棒性的矩形窄带滤光片的自动设计

分析了用于WDM光纤通信系统的全介质多腔窄带滤光片的膜系结构特点及其所必须具备的光学特性,提出了一种利用最优化方法的原理,通过计算机寻优来自动完成其膜系设计的方法;构造了合理的评价函数,编制了可自动搜索既满足设计目标、又具有鲁棒性的最优化膜系的计算机程序;使用本程序所设计出的多腔窄带滤光片具有较小的纹波系数和较好的矩形度,可满足WDM光纤通信系统对其分波/复波器的要求.     

Synthesis and Optical Properties of SiO2-Coated CeO2 Nanoparticles

Silica (SiO₂)-coated ceria (CeO₂) nanoparticles were prepared using water-in-oil microemulsion. Polyoxyethylene (15) cetylether and cyclohexane were used as a surfactant and organic solvent. SiO₂-coated CeO₂ nanoparticles were obtained by hydrolysis of metal alkoxide (tetraethylorthosilicate, TEOS) in the solution containing CeO₂ precursor nanoparticles. The effects of CeO₂ sources (Ce metal salt) and CeO₂ particle-forming agents on the morphology of SiO₂–CeO₂ particles were investigated. Observation via transmission electron microscopy revealed that the type of particle-forming agent affected the nanoparticles' morphology and that CeO₂ nanoparticles were spherically coated with SiO₂ when using oxalic acid ((COOH)₂) as a particle-forming agent of CeO₂. Furthermore, the transmittance of the particles was high in the visible region (above 400 nm) and decreased in the ultraviolet region.     

基于SSPCM的新型储能型太阳能蒸馏器实验研究

本文基于定型相变材料(SSPCM)建立了新型储能型太阳能蒸馏器的实验系统,并分别对普通SSPCM和高导热SSPCM的蒸馏特性进行了实验研究.研究发现:与传统太阳能蒸馏器相比,基于普通SSPCM的储能型蒸馏器的日产量提升了 7.5％,采用高导热SSPCM的日产量提升了 39％.此外,本文还对蒸馏器结构进行了优化研究,研制...     

等离子体结合六甲基二硅胺烷处理提升增透膜抗真空污染性能研究

本文采用溶胶-凝胶法制备了SiO₂增透膜,然后对其进行等离子体结合六甲基二硅胺烷（HMDS）表面改性处理。研究了后处理改性对增透膜表面形貌、微观结构、光学性能及激光损伤性能的影响规律,获得了抗真空有机污染的二氧化硅增透膜。结果表明,增透膜在采用等离子体结合HMDS表面改性处理后,膜层收缩、粗糙度下降、极性羟基等有机基团含量减少;两步后处理改善了增透膜膜层结构和光学性能,显著提高了膜层疏水能力和真空条件下的抗污染性能,并且对溶胶-凝胶二氧化硅增透膜的高损伤阈值属性不产生影响。     

耐高温CrAlON基太阳能光谱选择性吸收涂层的制备与热稳定性

光谱选择性吸收涂层是太阳能光-热利用技术的核心部件,直接决定着整个系统的转换效率,为了提高涂层的选择吸收性和热稳定性,本文提出以金属氮化物替代金属纳米颗粒,构建纳米晶-非晶异质结构的思路,并采用多弧离子镀制备了Cr/CrAlN/CrAlON/CrAlN/CrAlON/CrAlO多吸收层光谱选择性吸收涂层,其吸收率达0....     

宽截止窄带高反射滤光膜设计

窄带高反射滤光膜在光通讯、光学探测仪器等领域有着重要应用.探讨了"基片|H(LH)m1aL(HL)m2βCr,M|空气"膜系结构的窄带高反射滤光膜系,讨论了金属Cr层厚度,以及两种不同的匹配膜系对滤光膜特性的影响,计算了Cr层内部的电场分布.结果表明,较厚的金属层可实现更宽的截止带宽,匹配层的加入有效地实现了宽截止带的深截止,使中心波长处导纳为较大值的匹配膜系可以更好地实现滤光膜宽截止、窄带高反射特性;匹配膜层使中心波长处Cr层内部的电场强度趋于零,有效地降低了整个膜系的吸收,提高了反射率.     

Laser surface alloying of an electroless Ni–P coating with Al-356 substrate

Laser surface alloying of an electroless plating Ni–P coatings on an Al-356 aluminium alloy was carried out using a 1-kW pulsed Nd:YAG laser. The microstructure, chemical composition and phase identification of the alloyed layer were determined using scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX) and X-ray diffractometry (XRD), respectively. It was shown that laser surface treatment produced a relatively smooth, crack-free and hard surface layer. The hardness of the surface significantly increased due to the formation of the uniformly distributed fine Ni–Al intermetallic phases. The corrosion behaviour of the surface alloyed specimens in 3.5% NaCl solution at 23 °C was also determined by electrochemical techniques. The laser-alloyed surface showed an improved corrosion and pitting potential compared to the substrate as well as the plated Ni–P coating.     

旋涂法制备氧化锆介质层及其在薄膜晶体管中的应用

采用旋涂法制备了氧化锆介质层薄膜,重点讨论了退火温度以及旋涂转速对薄膜性能的影响及作用机制。研究发现高温后退火一方面使得氧化锆水合物脱水形成氧化锆,另一方面促使氧化锆薄膜结晶。此外,转速较高时,其变化对薄膜厚度及粗糙度无显著影响。当转速为5 000 r/min、退火温度为300℃时,制备的绝缘层厚度具有良好的厚度均匀性,粗糙度为0.7 nm,漏电流为3.13×10^-5 A/cm²（电场强度1 MV/cm）。最终,利用ZrO₂薄膜作为栅极绝缘层,在玻璃基板上制备了铟镓锌氧化物-薄膜晶体管（IGZO-TFT）,其迁移率为6.5 cm²/（V·s）,开关比为2×10⁴。     

Electrical and optical properties of Si-doped indium tin oxides as transparent electrode and anti-reflection coating for solar cells

We have studied the electrical and optical properties of Si-doped indium tin oxides (ITSOs) as transparent electrodes and anti-reflection coatings for Si-based solar cells. The ITSO thin films were obtained by co-sputtering of ITO and SiO₂ targets under target power control. The resistivity of the ITSO thin films deposited at 0.625 in terms of power ratio (ITO/SiO₂) were 391 Ωcm. In this condition, the ITSO thin films showed very high resistivity compared to sputted pure ITO thin films (1.08 × 10⁻³ Ωcm). However, refractive index of ITSO thin films deposited at the same condition at 500 nm is somewhat lowered to 1.97 compared to ITO thin films (2.06). The fabricated graded refractive index AR coatings using ITO, ITSO, and SiO₂ thin films kept over 80% of transmittance regardless of their thickness varing from 97 nm to 1196 nm because of their low extinction coefficient. As the AR coating with graded refractive indices using ITO, ITSO, and SiO₂ layers was applied to general silicon-based solar cell, the current level increased nearly twice more than that of bare silicon solar cell without AR coating.     

The use of macroscopic modelling of intermetallic phases in aluminium alloys in the study of ferricyanide accelerated chromate conversion coatings

Chromate conversion coatings are used on aluminium alloys, primarily for their renowned corrosion resistant properties. Although these coatings are in common industrial use, neither the protection mechanisms, nor the coating interation with the intermetallic precipitation phases are fully understood. Macroscopic models have been developed in order to represent the galvanic cells present in aluminium alloys due to the presence of such intermetallic particles. Particles modelled include CuAl₂, FeAl₃ and Cu₂FeAl₇, all know to be cathodic to the aluminium matrix. Variations in deposition, both in composition and thickness, are indicative of the mechanisms of deposition over each phase. Characterisation of the coating deposition was carried out using X-ray photoelectron spectroscopy, Rutherford backscattering spectroscopy, Auger electron spectroscopy, scanning electron microscopy with X-ray analysis. Depositional characteristics have been determined for each phase. The coating on the intermetallic phases is primarily Al oxide, and is significantly thinner than the coating on the matrix. This coating on the matrix consists mainly of a mixed Cr/Al oxide. The coating on the intermetallic phases was only one tenth the thickness of the matrix coating, and contained higher levels of Fe, Al and O. Matrix coating chemistry predominated with Cr, O, Fe and N, indicative of a chromate conversion coating. The mechanism for reduced rates of deposition over intermetallic phases was found to be affected by fluorine ion attack leading to intermetallic de-alloying and decomposition of Fe(CN)₆²⁻ accelerator into amide groups on the matrix.