Near-barrier fusion reactions induced by α on197Au,193Ir,191Ir,185Re,181Ta,121Sb and69Ga nuclei

Fusion-evaporation cross-sections for the α-induced reactions upon¹⁹⁷Au,¹⁹³Ir,¹⁹¹Ir,¹⁸⁵Re,¹⁸¹Ta,¹²¹Sb and⁶⁹Ga nuclei at bombarding energies near the Coulomb barrier have been measured by off-line observation of the γ-rays emitted in the radioactive decay of the residual nuclei using stacked foil technique. The total fusion cross-section for the systems have been compared with simple statistical model calculations using the code ALICE/91 as well as with the coupled channel calculations that include the β₂ and ν₄ slatic deformations and dynamic couplings of the vibrational/rotational states of the target and the projet tile using the code CCDEF.     

高功率横流CO2激光器脉冲预电离过程研究

本文给出了对高功率横流CO_2激光器脉冲预电离过程的理论和实验研究.表明了预电离过程中光电离的重要作用.实验结果表明,脉冲预电离可增大高功率横流CO_2.激光器的pd值(p为放电气压、d为放电间隔),增大放电区注入功率密度.对于提高此类型激光器的放电稳定性和输出激光功率是一种技术简单而有效的手段.     

Outflow refreshment angiography: A bright blood, bright static tissue technique

A new “bright blood” strategy, outflow refreshment imaging, is introduced in which a number of overlapping slices are excited in rapid succession. Flowing spins that refresh each overlapped slice portion contribute a bright signal. Additionally, static tissue in each non-overlapped slice portion also yields a bright signal. However, the flow/static contrast is comparable to that produced in inflow refreshment images, and angiograms can be generated by conventional maximum intensity projection processing. The dual ability to visualize angiograms and static tissue images is a major benefit of the strategy. Computer simulations of flow sensitivities and in vivo results are presented which compare the outflow and inflow refreshment imaging strategies.     

Chalcogenide based all-solid-state thin electroplated ion-selective membrane for Hg(II) flow-injection determinations

The response to Hg(II) of a thin all-solid-state Te-doped silver chalcogenide membrane, described by the general formula Ag₂ + δSe_{1 − x}Te_x, which has been electrochemically prepared following a previously proposed approach, has been investigated. The kinetics of formation of the membrane's secondary dynamic response to Hg(II) has been successfully combined with the precise timing and transient signal, typical for flow-injection (FI) measurements, in developing a sensitive and reliable mercury FI detector. Under optimized stream conditions it exhibits a linear Nernstian response, with a double slope of the calibration graph of 59 mV dec⁻¹, over the mercury(II) concentration range 10⁻⁶ − 10⁻³ M, the typical sample throughput amounting to about 70 samples per hour. The observed chemical amplification of the signal is due to the specificity of the processes dominating the initial step in formation of the steady-state signal of the membrane to mercury. The analytical performance of the Hg(II) FI detector, as regards sensitivity, reproducibility, selectivity and long-term stability has been thoroughly investigated. The exact procedure for membrane electrodeposition is given and the potential of the proposed approach as a cost-effective way for preparing chalcogenides of unique structure and properties has been outlined in the above context.     

New fluorescence probes for monitoring the kinetics of laser-initiated polymerization

Several new fluorescence probes useful for following photopolymerization have been characterized. Among these are probes which can be used in rapidly gelling monomer mixtures and for photochemical polymerization initiated by very high laser powers. Systems which can be used with polyolacrylates and either with visible initiators or with UV initiators are reported. © 1993 John Wiley & Sons, Inc.     

Stationary Distribution Function Estimation for Ergodic Diffusion Process

The problem of nonparametric stationary distribution function estimation by the observations of an ergodic diffusion process is considered. The local asymptotic minimax lower bound on the risk of all the estimators is found and it is proved that the empirical distribution function is asymptotically efficient in the sense of this bound.     

Heat-treatment studies of molybdenum oxide-monohydrate

The dehydration of molybdic acid, MoO₃---H₂O, was studied by thermal analysis, X-ray diffractometry and FTIR spectroscopy. The results show that an intermediate phase, MoO₃-2/3H₂O is formed at 216 °C and the monoclinic form of MoO₃ is grown above 350 °C. The mechanism of dehydration and structural rearrangement were confirmed by the features of the infrared spectra showing formation of corner-shared MoO₆ octahedra.     

Miscible blends of modified poly(aryl ether ketones) with aromatic polyimides

The phase behavior of binary blends of poly(ether ether ketone) (PEEK), sulfonated PEEK, and sulfamidated PEEK with aromatic polyimides is reported. PEEK was determined to be immiscible with a poly(amide imide) (TORLON 4000T). Blends of sulfonated and sulfamidated PEEK with this poly(amide imide), however, are reported here to be miscible in all proportions. Blends of sulfonated PEEK and a poly(ether imide) (ULTEM 1000) are also reported to be miscible. Spectroscopic investigations of the intermolecular interactions suggest that formation of electron donoracceptor complexes between the sulfonated/sulfamidated phenylene rings of the PEEKs and the n-phenylene units of the polyimides are responsible for this miscibility. © 1993 John Wiley & Sons, Inc.     

Complementary spectroscopic techniques to model the association of contaminant uranium with structural surfaces

Contaminant uranium poses unique problems for decontamination of former weapons processing and nuclear power facilities, as well as chemical plants, waste storage sites and former mining facilities. In addition, dealing with the possibility of intentional (i.e., a terrorist act) or accidental release of radioactive material in a populated area requires an accurate understanding of the nature of the association of such material with structural surfaces. These surfaces must also be considered in the context of repeated contamination, and the importance of atmospheric exposure, interaction with other possible contaminants, and corrosion or surface degradation due to such exposure must be taken into account. Complementary spectroscopic techniques, especially surface spectroscopies, are essential in developing models for the interaction of contaminants with surfaces and interfaces. In this review (which also presents new data on uranium association with corroding steel surfaces), we collect models of this association as determined by spectroscopic techniques, assess the important considerations in the development of more accurate models, and address some of the questions which remain.