Precision and sensitivity optimization of quantitative measurements in solid state NMR

This work presents a methodology for optimizing the precision, accuracy and sensitivity of quantitative solid state NMR measurements based on the external reference method. It is shown that the sample must be exclusively located within and completely span the coil region where the NMR response is directly proportional to the sample amount. We describe two methods to determine this "quantitative" coil volume, based on whether the probe is equipped or not with a gradient coil. In addition, to improve the sensitivity and the accuracy, an optimum rotor packing design is described, which allows the sample volume of the rotor to be matched to the quantitative coil volume. Experiments conducted on adamantane and NaCl, which are representative of a soft and hard material, respectively, show that one order of magnitude increase in experimental precision can be achieved with this methodology. Interestingly, the precision can be further improved by using the ERETIC method in order to compensate for most instrumental instabilities.     

MR diffusion - "diffraction" phenomenon in multi-pulse-field-gradient experiments

Using pulsed-field-gradient (PFG) experiments, the sizes of the pores in ordered porous media can be estimated from the "diffraction" pattern that the signal attenuation curves exhibit. A different diffraction pattern is observed when the experiment is extended to a larger number (N) of diffusion gradient pulse pairs. Simulations to calculate signal values from arbitrary gradient waveforms are performed for diffusion in restricted geometries using a matrix operator formalism. The simulations suggest that the differences in the characteristics of the attenuation curves are expected to make it possible to measure smaller pore sizes, to improve the accuracy of pore size measurements and potentially to distinguish different pore shapes using the N-PFG technique. Moreover, when an even number of PFG pairs is used, it is possible to observe the diffraction pattern at shorter diffusion times and measure an approximation to the average pore size even when the sample contains pores with a broad distribution of sizes.     

An optimization method for designing SENSE imaging RF coil arrays

An optimization method in RF coil array design for SENSE imaging is described. Using this method the optimized RF coil geometries can be calculated numerically given the required SENSE imaging performance. Although this method can be applied to optimize the RF coil arrays for both 1D and 2D SENSE imaging, to demonstrate the potential applications of this method, we designed RF coil arrays for 2D SENSE imaging and compared their performance by simulation. An optimized 4-channel receive-only RF coil array designed for 2D SENSE imaging was implemented and tested to demonstrate the feasibility of the proposed technique. Imaging results showed reasonable agreement with the simulations, thus the method can be applied to RF coil array designs for SENSE imaging when optimum imaging performance is desired.     

纳米氧化锌的过饱和控制生长与大小分布控制.

"在非水介质中合成了纳米氧化锌,测定了纳米氧化锌的紫外吸收光谱,并用有效质量模型计算了粒子大小,开发并命名了一种称之为纳米粒子过饱和控制生长的技术,该技术涉及将小的纳米粒子悬浊液加入到大的粒子悬浊液中,结果因为不同大小粒子间的溶解度差异小的粒子将全部溶解,大的粒子将整体长大,大粒子悬浊液的粒子数将保持不变,大粒子的生长速度显著比Ostwald老化的高．该技术最显著的特征是只要最初两悬浊液粒子大小的差异足够大,分布不是太宽,则粒子大小的分布将会因为粒子如此长大而变窄．"     

对BJH方法计算孔径分布过程的解读

This paper introduces the geometric assumptions and neglects of the pore size distribution calculated by BJH method, the arithmetic approximation for simplified calculation, the derivation process of each parameter, the calculation steps and key points of the pore size distribution. This paper also introduces the application scope of BJH method at the current instrument level, and how to further integrate the data. In order to get the required analysis and test report, references are provided for the subsequent adjustment of test parameters and improvement of test methods. Some problems often encountered in reading experimental reports are also discussed.     

Effect of Gaussian size distribution width on minimum fluidization velocity in tapered gas–solid fluidized beds

This paper investigated the effect of Gaussian distribution width, average particle diameter, particle loading, and the tapered angle on minimum fluidization velocity (U_mf) by conducting extensive experiments in tapered fluidized beds. Three powders with Gaussian size distribution and different distribution widths were used in the experiments. An increase in U_mf with increasing the average particle diameter, particle loading, and the tapered angle was observed. There was also a nonmonotonic behavior of U_mf as the Gaussian distribution width increased. An empirical correlation including dimensionless groups for predicting U_mf in tapered beds was developed in which the effect of distribution width was considered. The proposed correlation predictions were in good agreement with the experimental data, with a maximum deviation of 16.5% and average and standard deviations of, respectively, 6.4% and 7.4%. The proposed correlation was also compared with three earlier models, and their accuracy was discussed.     

Experimental investigation on the distribution uniformity and pressure drop of perforated plate distributors for the innovative spray-type packed bed thermal storage

As an innovative thermal energy technology, the spray-type packed bed has advantages of high efficiency and low cost. A liquid distributor is the key component for the spray-type packed bed for scattering heat-transfer liquid drops evenly. In this study, the distribution performance and pressure drop of the perforated plate distributors of different orifice diameters were studied experimentally. The experimental results indicate that orifice diameter has a greater effect on the distribution performance compared to flow rate. With an increase in flow rate, the flow pattern through the distributor changes from the uncovered drop to the covered drop and then to the jet flow. The covered drop pattern shows the best performance with a good distribution and a small pressure drop simultaneously, which is the design and optimization principle of the distributor for a spray-type packed bed.     

一类新的红色荧光粉MY2S4:Er3+(M=Sr2+,Ba2+)的合成与表征

Eu2 激活的CaS: Eu[1],Eu3 激活的硫氧化物[2],Pr3 激活的Ca0.8Zn0.2TiO3[3]以及Eu2 和Mn2 掺杂的SrY2S4[4]都是重要的红色发光材料.     

新型三段高性能的长波段掺铒光纤超荧光光源的研究

提出了一种第一段无泵浦、第二段前向泵浦和第三段后向泵浦的三段级联掺铒光纤超荧光光纤光源的新结构.数值分析了泵浦光波长、铒光纤长度以及泵浦比例对新结构性能的影响.结果表明可以找到一组适合制作成本低廉、输出功率高、谱平坦的长波段掺铒光纤超荧光光源.     

6，6＇－二（二苯基氧化膦甲基）－1，1＇－氮氧化－2，2＇－联吡啶与硝酸铒配合物的合成与结构

合成了硝酸铒与四功能团含磷萃取剂６，６＇－二（二苯基氧化膦甲基）－１，１＇－氮氧化－２，２＇－联吡啶的配合物。用四圆衍射仪测定了配合物的晶体结构。晶体属单斜晶系，空间群Ｃ２／ｃ，晶体学参数，ａ＝１．９８３０（４）ｎｍ，ｂ＝２．３１３５（４）ｎｍ，ｃ＝１．８６００（３）ｎｍ；β＝９６．１８（２）°，ｚ＝４。配合物中有机配体以四齿形式与中心离子铒配位，金属离子的配位数为８。配位几何构形为稍变形的四方反棱柱。金属离子周围的配位水分子已全部被取代。