An efficient lasing action from pyrromethene 556 dye-doped organically modified silicates

Organically modified solid-state silicates (ORMOSILS) doped with a new laser dye 1,3,5,7,8-pentamethylpyrromethene-2,6-disulfonate-BF₂ complex (pyrromethene 556) have been synthesized by a sol-gel method and the compositional effects on pore characteristics, fluorescence and lasing properties have been investigated. It is found that the use of dimethylsulfoxide and γ-glycidoxypropyltrimethoxysilane could greatly change the structure properties of sol-gel derived ORMOSILS cage, and thus the fluorescence and lasing properties of the materials could improve significantly. A successful laser oscillation from this dye-doped ORMOSILS sample has been achieved upon pumping with a Q-switched frequency-doubled Nd:YAG laser at 532 nm. A slope efficiency of 54% with a useful lifetime greater than 10,000 shots has been demonstrated at a pump repetition rate of 1 Hz and a pump intensity of 1 J/cm² by using the new ORMOSILS cage on our newly designed laser system. Our results have shown that it is possible to obtain a high-efficiency with a long-lifetime for a compact new laser device by low cost dye-doped solid-state ORMOSILS.     

Spectroscopic study on the complex formation of chromogenic bridged calixarenes with aliphatic amines

The complex formation between chromogenic capped calix 4 arene derivatives comprising indophenol indicator group(s), and aliphatic amines has been studied by UV/Vis spectroscopy. The equilibrium constants have been determined in ethanol, and—for one ligand—also in dimethylsulfoxide. The results have been interpreted in terms of various types of host–guest interactions and of steric effects.     

An estimation of the measurement uncertainty for an optical emission spectrometric method

 A validation procedure based on the ISO/IEC 17025 standard was used to demonstrate the long-term stability of a calibration process and to assess the measurement uncertainty of a standard test method for optical emission vacuum spectrometric analysis of carbon and low-alloy steel (ASTM E 415–99a). The validation was used to provide documented evidence that the selected method fulfils the requirements and that the method is ”fit for purpose”. A test for drift was applied to determine statistically whether the analytical results vary systematically with time. The accuracy and traceability of the optimised method were tested by an analysis of closely matched matrix certified reference materials (CRMs). The measurement uncertainty estimations took account of the precision study, the bias and its uncertainty, and the qualification of uncertainties not considered in the overall performance studies. Received: 2 November 2002 Accepted: 2 January 2003 Acknowledgement The author expresses gratitude to Dr. Aleš Fajgelj for helpful discussions during the 3rd Central European Conference on Reference Materials and Measurements. Presented at CERMM-3, Central European Reference Materials and Measurements Conference: The function of reference materials in the measurement process, May 30–June 1, 2002, Rogaška Slatina, Slovenia Correspondence to T. Drglin     

Optical investigation of cavitation erosion by laser-induced bubble collapse

By means of a new force sensor based on optical beam deflection (OBD), the mechanical effects of laser-matter interaction underwater at different incident laser energy are investigated in detail. The experimental results show that a target underwater is impacted in turn by laser-plasma ablation force and high-speed liquid-jet impulse induced by bubbles collapse in the vicinity of a solid boundary. Furthermore, the amplitudes of the two forces increase monotonously with laser energy. According to the ablation force detected by the experiment and the theoretical relationship between laser intensity and ablation pressure, the value of liquid-jet impact against a solid boundary can be easily obtained. In addition, based on the model of a collapsing bubble, some characteristic parameters, such as the liquid-jet impact velocity, the maximum bubble radius, the bubble energy can also be obtained at different laser energy, which are valuable in the corresponding research fields.     

利用计算机辅助装调检测矩形大口径离轴非球面的方法研究

通过非球面的零位补偿法,完成了对矩形大口径离轴非球面镜的检测。先用光学设计软件Zemax从理论上分析了在检测中会出现的现象,并结合计算机辅助装调技术,确定在检测过程中相对敏感的自由度,然后控制这些量,使补偿器和非球面的相对关系与理论设计相吻合,在Zygo相位干涉仪上测得最终结果。在λ=632.8nm时,中心圆口径与两个边缘圆口径面形误差RMS分别为0.022λ,0.037λ,0.032λ。检测结果,达到预期目的。     

Extremely large binding energy of biexcitons in an organic-inorganic quantum-well material (C4H9NH3)2PbBr4

We have confirmed biexciton formation in an organic-inorganic hybrid quantum-well material (C₄H₉NH₃)₂PbBr₄ by photoluminescence and two-photon absorption measurements. The biexciton has extremely large binding energy, 60 meV, which to our knowledge is the largest value ever reported for a semiconductor. By analyzing the spectrum of biexciton luminescence, the biexciton gas temperature was found to be much higher than the bath temperature due to a higher local temperature arising from the large biexciton binding energy.     

Development of a Millimeter Wave Compact Equipment for NDT of Materials

We developed a compact equipment working at 94 GHz to replace the commonly used network analyzer for nondestructive testing of materials. The compact equipment was designed to measure the variations in the amplitude and phase of the reflected signal from the material relative to a reference signal. A good accuracy of the amplitude and phase measurement of the equipment was obtained in the confirmative experiments. The distribution of a drop of water in a wood plate is clearly visible in the millimeter wave images obtained by the amplitude and phase measurement.     

Optical and conductive properties of AlSi-alloy/SiCp composites: application in modelling CO2 laser processing of composites

The optical properties—reflectivity, real part of the refractive index, absorption coefficient as well as the thermal and electrical conductivity of AlSi-alloy/SiC_p composite were measured. The optical parameters and both conductivities decreased with the increase of SiC_p particles volume in AlSi-alloy matrix. This decrease was almost linear for the volume fraction of SiC_p particle up to 10 vol% of the total mass of the composite. For the 15 vol% of SiC_p particles, the departure from linearity is connected with the presence of additional phases in AlSi-alloy/SiC_p composite materials. The measured temperature dependencies of optical reflectivity and electrical conductivity for AlSi-alloy/SiC_p 15 vol% are of metallic character. Modelling of the interaction of the CO₂ laser radiation with AlSi-alloy/SiC_p 15 vol% composite should allow to estimate the initiation time at which the surface composite reaches melting temperature.     

基于分层光学扫描的三维数字化测量技术

采用切削分层光扫描测量与计算机数据信息合成相结合的方法，有效地解决了具有复杂内外腔结构零件的三维数字化测量。该方法比传统三维测量速度快、自动化程度高，能同时准确测量零件内外腔表面，零件边缘测量误差可控制在CCD两个像素内。利用获取的铝合金精密小箱体三维数据，在计算机上重构了零件的三维模型，并用RP技术制造出了零件物理原形。     

Structure and optical properties of lead iodide based two-dimensional perovskite compounds containing fluorophenethylamines

Phenethylammonium-based perovskites, which can be regarded as a semiconductor/insulator multiple quantum well consisting of lead halide semiconductor layers sandwiched between phenethylammonium insulator layers were prepared. To investigate the effects of the electronic state and the orientation of organic insulator layers on the optical properties of layered perovskites, fluorine substituted analogues were also prepared. The structure and optical properties were investigated by the XRD, UV–Vis absorption, and fluorescence measurements. The exciton absorption peak was shifted by the substitution of fluorine atoms in organic ammonium compounds. It became clear that the optical properties of two-dimensional perovskite compounds were controlled by the substitution of fluorine atoms.