稳定分层二层流室内实验早期格栅湍流结构

采用室内实验混合箱和粒子图像测速技术,本文研究了稳定分层无平均剪切二层流(上层淡水、下层盐水)振动湍流结构.对实验录像进行粒子图像测速技术处理,获得垂向二维流场(垂直于格栅平面)瞬时速度和涡量,并用于计算:①时均速度和时均涡量;②均方根速度;③均匀程度和各向同性程度;④平均流强度;⑤时均泰勒的欧拉积分长度尺度;⑥时均湍...     

水下对转螺旋桨流致辐射噪声机理与预报方法*

水下对转螺旋桨流致辐射噪声的预报对于水下目标的特征提取和分类识别具有重要意义。由桨叶的旋转引起的湍流场是水下对转螺旋桨流致辐射噪声的源场。分述了水下对转螺旋桨湍流边界层脉动、旋转干涉效应和空化效应引发的水动力噪声机制和研究进展,比较了目前工程应用中的3种对转螺旋桨流致辐射噪声预报方法的特点。在分析对转螺旋桨流致辐射噪声数值预报难点的基础上,综述了对转螺旋桨流致辐射噪声计算方法的研究进展,指出间接数值模拟方法是工程中进行对转螺旋桨流致辐射噪声预报的有效方法。     

湍流大气传输中跟踪抖动对远场影响的仿真研究

分析了跟踪抖动对湍流大气传输远场光斑的影响。基于麦克斯韦电磁场理论,采用大气相干长度对大气湍流进行描述,推导了发射光束因跟踪抖动导致光轴偏离的远场表达式。在此基础上,利用相位屏法模拟抖动引起的倾斜相位和大气折射率起伏引起的相位调制,并采用低频补偿的功率谱反演法对传输过程进行了数值仿真。分析了不同跟踪抖动、湍流强度条件下远场光斑质心脱靶量的变化,以及不同尺寸模拟目标的回波概率。分析结果表明,在传输距离为10 km时,强湍流造成的远场光斑脱靶量可达几十μrad;当跟踪抖动较大时,湍流强弱对脱靶量影响差别很小。最后,对一定尺寸的模拟目标,从探测回波概率的角度给出了发射系统跟踪抖动量的控制范围。     

激光雷达扫描方式

为实现激光束对空域的有效扫描和探测,研究了栅形扫描、李萨茹形扫描、螺旋形扫描和六边形扫描四种常见的激光雷达扫描方式,推导了相应的扫描方程,讨论了参数的物理意义及调整方法;重点研究了栅形扫描和六边形扫描方式下光斑的分布情况,通过仿真分析了两种扫描方式下光束的漏扫率和重叠率,结果表明,在相同扫描条件下六边形扫描方式的漏扫区域最少。展示了基于上述研究内容的扫描控制系统实物图及扫描图案。分析总结了四种扫描方式的特点,给出了每种扫描方式的适用情况及使用建议。     

HL-2A装置中性束发射光谱 诊断系统的研制与测试

在HL-2A装置上完成了一套32通道束发射诊断系统(BES),可对径向r=12~44cm, 极向-7.5~+7.5cm二维空间范围内的长波长()电子密度扰动信息进行测量,其时间分辨率达到0.5ms,空间分辨率1~2cm。系统由内置于真空室的非对称镜头组、传输光纤、高性能探测器模块以及辅助的冷却和真空设备构成。系统的噪声在低频时(f<100kHz)主要由散粒噪声贡献,在较高频率时由散粒噪声和e噪声共同决定。在典型的HL-2A装置放电模式中,对于200kHz以下的扰动,该系统的信噪比(SNR)均大于3。     

EAST装置上W波段多道极向相关反射仪的研制

在EAST装置上安装了X模极化W波段多道相关反射仪,用于测量等离子体芯部密度涨落。该诊断利用低损耗(<3dB)多工器将4个不同频率(79.2GHz,85.2GHz,91.8GHz和96GHz)的微波耦合在一起,通过同一个天线发射。反射波由两个极向分离(~5cm)的天线接收,通过下变频技术实现外差测量。通过对两个极向天线接收的信号进行相关分析,获得芯部湍流垂直速度。对2018年低约束模式(L模)放电进行分析发现,在电子回旋共振加热(ECRH)等离子体中,芯部湍流垂直速度在电子逆磁漂移方向。而在注入同向中性束(co-NBI)后,芯部湍流垂直速度变为离子逆磁漂移方向。     

Interchange-turbulence-based radial transport model for SOLPS-ITER: A COMPASS case study

Mean-field plasma edge transport codes such as SOLPS-ITER heavily rely on ad-hoc radial diffusion coefficients to approximately model anomalous transport. Such coefficients are experimentally determined and vary between different machines, and also depend on the operational regime and plasma location within the same device. Therefore, to match experimental data the modeller is required to manually tune several free parameters in expensive simulations, and the code's predictive capabilities are significantly downgraded. As a solution, a new model has been developed for SOLPS-ITER, solving an additional transport equation for the turbulent kinetic energy k, derived by consistently time-averaging the Braginskii equations, and including a diffusive closure for the anomalous particle flux. This closure model relates the anomalous diffusion coefficient to the local k value. The resulting equation structure and its closure are inspired by TOKAM2D isothermal interchange turbulence simulation results. Within this model, fewer and hopefully more universal free parameters are retained, thus improving the code's predictive capabilities. The new model has been tested on a COMPASS case for which upstream plasma profiles were available. Experimental data and a reference solution, obtained by matching the profiles through manual tuning of radial diffusivities, have been used to estimate the parameters of our new transport model. A ballooned particle diffusivity profile is retrieved by the new radial transport model, thanks to the proposed interchange drive. The obtained upstream profiles qualitatively agree with the experiment and prove the new model is a promising first attempt to be further refined.     

Comparison of two cold atmospheric pressure plasma jet configurations in argon

The present study compares the operation of two cold atmospheric plasma jet (CAPJ) configurations: needle-to-cylinder electrode configuration (CAPJ I) and single high-voltage cylinder electrode around the quartz tube (CAPJ II). The CAPJs were operated in argon flowing through a quartz capillary with 0.5-mm inner diameter into the ambient air, and the plasma was generated by sinusoidal kHz frequency AC power supplies. The main emphasis of the study was on the mechanism of the initiation of ionization waves for these two configurations. For both CAPJs, there appeared several ionization waves during one half-period of the applied voltage waveform, and the number of ionization waves increased at higher voltage amplitudes. However, we discovered marked differences in the initiation of the ionization waves for two different CAPJ configuration. The applied voltage controlled the initiation of consecutive ionization waves, which propagated from the grounded electrode towards the tube orifice in CAPJ I. In the case of CAPJ II, certain time had to pass for the initiation of a new ionization wave, and subsequent ionization waves within the same half-period started at the tube orifice. In addition to the differences in the initiation of the ionization waves, we observed that the CAPJ I was ignited and sustained at lower voltages, while CAPJ II produced a longer plasma jet. The observed advantages and deficiencies of investigated CAPJ configurations point out their potential in different applications.     

Numerical and Experimental Investigation of the Conjugate Heat Transfer for a High-Pressure Pneumatic Control Valve Assembly

This paper uses heat transfer experiments and computational fluid dynamics (CFD) simulations to investigate the conjugate heat transfer (CHT) in a high-pressure pneumatic control valve assembly. A heat transfer test rig was constructed, and time–temperature histories of five test points placed on the valve assembly’s outer surface were recorded for study validation. The Unsteady Reynolds-Averaged Navier–Stokes (URANS) CFD methods with the standard k-ε turbulence closure equations were adopted in the numerical computations. Polyhedral grids were used; time step and mesh convergence studies were conducted. Simulated and measured temperatures profile comparisons revealed a good agreement. The CHT results obtained from CFD showed huge velocity fields downstream of the valve throat and the vent hole. The airflow through the valve was icy, mainly in the supersonic flow areas. Low temperatures below 273.15 K were recorded on the internal and external walls of the valve assembly. The consistency of the measured data with the numerical results demonstrates the effectiveness of polyhedral grids in exploring the CHT using CFD methods. The local entropy production rate analysis revealed that irreversibility is mainly due to viscous dissipation. The current CHT investigation provides a potential basis for thermostress analysis and optimization.