Vapor deposition of ultrathin hydrophilic polymer coatings enabling candle soot composite for highly sensitive humidity sensors

Candle soot (CS) is a desirable carbon nanomaterial for sensors owing to its highly porous nanostructure and large specific surface area. CS is advantageous in its low-cost and facile preparation compared to graphene and carbon nanotubes, but its pristine nanostructure is susceptible to collapse, hampering its application in electronic devices. This article reports conformal coating of nanoscale crosslinked hydrophilic polymer on CS film using initiated chemical vapor deposition, which well preserved the CS nanostructure and obtained nanoporous CS@polymer composites. Tuning coating thickness enabled composites with different morphologies and specific surface areas. Surprisingly, the humidity sensor made from composite with the lowest filling degree, thus largest specific surface area, showed relatively low sensitivity, which is likely due to its discontinuous structure, thus insufficient conductive channels. Composite sensor with optimum filling degree shows excellent sensing response of more than 10³ with the linearity of R² = 0.9400 within a broad relative humidity range from 11% to 96%. The composite sensor also exhibits outstanding sensing performance compared to literature with low hysteresis (3.00%), a satisfactory response time (28.69 s), and a fast recovery time (0.19 s). The composite sensor is fairly stable and durable even after 24 h soaking in water. Furthermore, embedding a humidity sensor into a face mask realizes real-time monitoring of human breath and cough, suggesting promising applications in respiratory monitoring.     

General expression of the calibration curve for the CR-39 radon track detectors

The CR-39 detectors are widely used as passive radon dosimeters, as well as in physics laboratories or for industrial applications. For what concerns radon monitoring, the calibration curve which is usually adopted corresponds to a linear relation between the actual etched track density and the track density counted by an automatic acquisition system. This linear calibration provides very accurate radon exposure assessments in a restricted range of etched track density, however it neglects the effect of the tracks overlapping that becomes as relevant as the track density increases. In the present work the mathematical expression of the area covered by a set of uniformly distributed tracks is deduced. This result allows then to infer the probability that the system acquires the right track density, providing a general calibration curve for a solid state radon track detector. The process of track production and reading routine is also simulated adopting a Monte Carlo approach, showing that the obtained results are in agreement with the function proposed as calibration curve. Moreover, a linear dependence between the track average area and the rate parameter of the calibration curve has been observed. Finally a semi-empirical correlation based on the previous results is proposed.     

CORSICA: correction of structured noise in fMRI by automatic identification of ICA components

When applied to functional magnetic resonance imaging (fMRI) data, spatial independent component analysis (sICA), a data-driven technique that addresses the blind source separation problem, seems able to extract components specifically related to physiological noise and brain movements. These components should be removed from the data to achieve structured noise reduction and improve any subsequent detection and analysis of signal fluctuations related to neural activity. We propose a new automatic method called CORSICA (CORrection of Structured noise using spatial Independent Component Analysis) to identify the components related to physiological noise, using prior information on the spatial localization of the main physiological fluctuations in fMRI data. As opposed to existing spectral priors, which may be subject to aliasing effects for long-TR data sets (typically acquired with TR >1 s), such spatial priors can be applied to fMRI data, regardless of the TR of the acquisitions. By comparing the proposed automatic selection to a manual selection performed visually by a human operator, we first show that CORSICA is able to identify the noise-related components for long-TR data with a high sensitivity and a specificity of 1. On short-TR data sets, we validate that the proposed method of noise reduction allows a substantial improvement of the signal-to-noise ratio evaluated at the cardiac and respiratory frequencies, even in the gray matter, while preserving the main fluctuations related to neural activity.     

石化厂区有毒气体泄漏在线监测平台的构建

针对石化厂区在生产过程中可能发生有毒气体泄露带来的生产安全问题,构建了石化厂区有毒气体在线监测平台。该平台是由PC监控中心、网络监控中心、ARM便携式终端、安卓手机客户端组成。实现对石化厂区中有毒气体及环境参数的实时、在线监测和预警,使生产管理人员掌握石化厂区的有毒气体实时动态信息,对可能引发危险事故的因素及时排除,把危险控制在始发阶段,以实现化工生产的安全、持续、高效进行。测试结果表明该平台能实现所设计的各项功能,并具有良好的稳定性、安全性和实用性。     

On‐Line Monitoring of Chemical Reactions by using Bench‐Top Nuclear Magnetic Resonance Spectroscopy

Real‐time nuclear magnetic resonance (NMR) spectroscopy measurements carried out with a bench‐top system installed next to the reactor inside the fume hood of the chemistry laboratory are presented. To test the system for on‐line monitoring, a transfer hydrogenation reaction was studied by continuously pumping the reaction mixture from the reactor to the magnet and back in a closed loop. In addition to improving the time resolution provided by standard sampling methods, the use of such a flow setup eliminates the need for sample preparation. Owing to the progress in terms of field homogeneity and sensitivity now available with compact NMR spectrometers, small molecules dissolved at concentrations on the order of 1 mmol L^?1 can be characterized in single‐scan measurements with 1 Hz resolution. Owing to the reduced field strength of compact low‐field systems compared to that of conventional high‐field magnets, the overlap in the spectrum of different NMR signals is a typical situation. The data processing required to obtain concentrations in the presence of signal overlap are discussed in detail, methods such as plain integration and line‐fitting approaches are compared, and the accuracy of each method is determined. The kinetic rates measured for different catalytic concentrations show good agreement with those obtained with gas chromatography as a reference analytical method. Finally, as the measurements are performed under continuous flow conditions, the experimental setup and the flow parameters are optimized to maximize time resolution and signal‐to‐noise ratio.     

Performance of an optical stabilization system at NSLS beamline U12IR

A low-cost optical feedback system using dynamic mirrors has been developed at the NSLS for stabilizing the position and direction of an infrared synchrotron beam against thermal drift and mechanical noise. The system design has some unique features that potentially simplify installation into an existing infrared beamline. We describe the system and its features along with some performance results.     

Live Monitoring of Strain-Promoted Azide Alkyne Cycloadditions in Complex Reaction Environments by Inline ATR-IR Spectroscopy

The strain-promoted azide alkyne cycloaddition (SPAAC) is a powerful tool for forming covalent bonds between molecules even under physiological conditions, and therefore found broad application in fields ranging from biological chemistry and biomedical research to materials sciences. For many applications, knowledge about reaction kinetics of these ligations is of utmost importance. Kinetics are commonly assessed and studied by NMR measurements. However, these experiments are limited in terms of temperature and restricted to deuterated solvents. By using an inline ATR-IR probe we show that the cycloaddition of azides and alkynes can be monitored in aqueous and even complex biological fluids enabling the investigation of reaction kinetics in various solvents and even human blood plasma under controlled conditions in low reaction volumes.     

Trends in the use of passive sampling for monitoring polar pesticides in water

The presence of polar pesticides in environmental waters is a growing problem. After application their migration into the aqueous phase is promoted by their high water solubility. Transport processes are usually complex and inputs are generally stochastic; this makes monitoring of this class of pesticides challenging using low volume spot samples of water. Recently there has been a trend to use passive samplers to monitor pesticides in river catchments as it is an in-situ time integrative sampling technique. The three main types of device used for this purpose are, Chemcatcher®, POCIS and o-DGT. This article reviews the fate and current state-of-the-art for monitoring polar pesticides in aqueous matrices. Principles and the theory of passive sampling and strategies for passive sampler design and operation are presented. Advances in the application of passive sampling devices for measuring polar pesticides are extensively critiqued; future trends in their use are also discussed.     

pH electrodes based on iridium oxide films for marine monitoring

The pH is an important parameter that affects the growth and development of marine organisms, environmental changes, and industrial and agricultural production processes. Nowadays, important trends in pH detection and analysis are higher stability, adaptation to extreme environmental conditions, miniaturization, portability, and digital intelligence. Several studies have focused on the application of the iridium oxide film (IROF) pH electrodes in water quality monitoring and physiological analysis. The central aim of this work was to review the preparation techniques of the IROF pH electrodes and to expand their application in the field of marine monitoring. The studied methods include electrochemical deposition, electrochemical growth, sputtering deposition, heat treatment, and novel preparation methods. The IROF pH electrodes prepared via these methods are more sensitive, have a wider pH measurement ranges, and can be miniaturized further than traditional glass and pH photometer. Hence, in environmental analysis, combining IROF pH electrodes with wireless technology for the physiological and biochemical analysis of marine organisms, seawater, and sediment pore water is an important development tendency.     

Portable capillary liquid chromatography for pharmaceutical and illicit drug analysis

A newly developed portable capillary liquid chromatograph was investigated for the separation of various pharmaceutical and illicit drug compounds. The system consists of two high‐pressure syringe pumps capable of delivering capillary‐scale flow rates at pressures up to 10 000 psi. Capillary liquid chromatography columns packed with sub‐2 μm particles are housed in cartridges that can be inserted into the system and easily connected through high‐pressure fluidic contact points by simply applying a specific, predetermined torque rather than using standard fittings and less precise sealing protocols. Several over‐the‐counter analgesic drug separations are demonstrated, along with a simple online measurement of tablet dissolution. Twenty illicit drug compounds were also separated across six targeted drug panels. The results described in this study demonstrate the capability of this compact liquid chromatography instrument to address several important drug‐related applications while simplifying system operation, and greatly reducing solvent usage and waste generation essential for onsite analysis.