Trace analysis of Pt (IV) metal ions in roadside soil and water samples by Fe3O4/graphene/polypyrrole nanocomposite as a solid-phase extraction sorbent followed by atomic absorption spectrometry

A novel Fe₃O₄/graphene/polypyrrole nanocomposite has been successfully synthesised via a simple chemical method and applied as a new magnetic solid-phase extraction (MSPE) sorbent for the separation and pre-concentration of trace amounts of Pt (IV) in environmental samples followed by flame atomic absorption spectrometric (FAAS) detection. The nanocomposite has been characterised by scanning electron microscopy (SEM), transmission electron microscopy (TEM) and Fourier transform infrared (FTIR) spectroscopy. Seven important parameters, affecting the extraction efficiency of Pt (IV), including pH, adsorption time, desorption solvent type and concentration, desorption time, elution volume and sample volume, were investigated. Under the optimised conditions, the calibration graph was linear in the range of 50–1500 μg L^?1 (R = 0.993). The detection limit and pre-concentration factor (PF) for Pt (IV) were found to be 16 μg L^?1 and 112.5, respectively. Under the optimised solid-phase extraction (SPE) conditions, the adsorption isotherm and the adsorption capacity of the nanocomposite for Pt (IV) were studied. Pt (IV) adsorption equilibrium data were fitted well to the Langmuir isotherm and the maximum adsorption capacity of the magnetic sorbent was calculated from the Langmuir isotherm model as 416.7 mg g^?1. The precision of the method was studied as intraday and interday variations. A relative standard deviation percentage (RSD%) value less than 3.0 indicates that the method is precise. Also, the accuracy of the method was tested by the analysis of the standard reference material (NIST SRM 2556) and by recovery measurements on spiked real samples. It was also shown that the optimised method was suitable for the analysis of trace amounts of Pt (IV) in roadside soil, tap water and wastewater samples.     

贫燃条件 In-Ag/TiO2-γ-Al2O3催化 CO选择性还原NO

汽车尾气中主要污染成分 CO和 NOx可导致酸雨、光化学烟雾和臭氧空洞效应,对生物、环境及生态系统造成重大危害。污染源中 CO是性能优良的还原剂,如能不添加还原剂实现 CO催化还原 NOx,将成为最具经济技术优势的 NOx脱除技术。在富氧、低温条件下,利用 CO选择性催化还原 NOx为 N2,是目前选择性催化还原研究中的热点和难点。催化 CO还原 NOx常用的贵金属 Ir, Rh, Pt和Pd矿藏稀少,价格昂贵,有氧条件下活性急降,而分子筛催化剂和一些金属氧化物催化剂普遍存在反应温度高,尤其对 N2选择性差等问题。为解决上述问题,需寻找新的适合我国矿产资源的催化体系。研究发现,稀散金属基催化剂对氮氧化物的净化具有一定效果,因而可将我国的稀散金属资源优势转化为技术优势和经济优势。因此,本文以 TiO2-γ-Al2O3(TA)为载体, In/Ag为活性组分,采用等体积浸渍法制备了 InAg/TA以及 In/TA, Ag/TA和InAg/Al (γ-Al2O3为载体)催化剂,考察了贫燃条件下 CO选择性还原NO的催化活性。研究表明,双金属催化剂InAg/Al和 InAg/TA的活性比单金属催化剂In/TA和 Ag/TA高, In/TA催化剂中引入 Ag物种能降低起燃温度;另外,相比于InAg/Al催化剂, InAg/TA催化剂具有较高的催化活性,550?600°C时 N2产率超过60%,说明载体中引入TiO2可以提高催化剂活性。为了深入研究 InAg/TA催化剂中 Ag物种和TiO2对 In物种的作用,通过比表面测定、X射线衍射(XRD)、透射电子显微镜(TEM)、X射线光电子能谱、紫外-可见光吸收光谱、氢气程序升温还原、傅立叶变换红外线光谱等方法分析了催化剂结构和表面形态。结果表明, Ag物种可以提高 In物种的分散性, In和 Ag物种在 TA载体表面可以很好地分散,从而有利于提高催化活性。 In和 Ag物种在 TA载体表面以氧化态形式存在,并且 Ag物种可以提高 In物种表面含量,表面 In和 Ag物种含量越高,吸附活性位越多,催化活性越高;同时, TiO2也可以促进 NO吸附,从而提高 InAg/TA催化剂活性。 InAg/TA催化剂在450°C连续反应72 h进行稳定性测试,测试前后分别在50?600°C进行活性测试,并用 XRD和 TEM对反应后的催化剂进行表征测试。结果表明, InAg/TA催化剂具有较好的稳定性,连续反应前后催化剂活性基本保持不变,推测可能由于在有 CO和O2存在的体系中, Ag物种利用自身 Ag+与 Ag0之间的氧化还原反应抑制了活性组分 In2O3的还原和聚集,稳定了 In物种乃至催化剂活性。 InAg/TA催化剂用于贫燃条件下CO还原NO具有较好的催化效果,主要归因于催化剂活性组分分散性好,稳定性高,对NO吸附能力强。 Ag物种可以稳定In物种并提高其分散性, TiO2可以改善In物种和Ag物种的分散性并促进NO吸附。     

Zr 改性MnOx/MWCNTs催化剂的结构特征与低温SCR活性

以ZrO（NO₃）₂·2H₂O为前驱体对多壁碳纳米管（MWCNTs）进行了改性并负载MnO_x制备了MnO_x/ZrO₂/MWCNTs 催化剂. 考察了Zr 对催化剂低温选择性催化还原（SCR）反应活性的影响,并通过多种分析手段对催化剂的结构进行了表征. 结果表明Zr 的添加对催化剂的低温SCR活性具有显著的促进作用,当Zr 负载量为30%时,催化剂活性最佳. X射线衍射（XRD）、拉曼（Raman）光谱、透射电镜（TEM）、N₂吸附-脱附的表征结果分析表明,适量的Zr 改性促进了MnO_x在载体表面的分散,增强金属氧化物与MWCNTs 之间的作用,也能增加催化剂的比表面积、孔容和孔径. X 射线光电子能谱（XPS）、H₂程序升温还原（H₂-TPR）和NH₃程序升温脱附（NH₃-TPD）的分析结果则显示,Zr 能提高催化剂表面化学吸附氧浓度,促进Mn³⁺转化为Mn⁴⁺,从而使催化剂表面的活性位点增多,氧化还原能力增强,同时还提高了催化剂表面酸性位点的数量和强度,促进了NH₃的吸附,是MnO_x/ZrO₂/MWCNTs 催化剂低温SCR活性提高的主要原因.     

用Lewis酸或Brnsted酸催化剂和N2汽提法使木糖脱水为糠醛（英文）

The activity of Lewis (Nb2O5) and Br nsted (Amberlyst 70) acid catalysts for the cyclodehydration of xylose to furfural was studied. The nature of the acidity resulted in significant changes in the reaction mechanism. Lewis acid sites promote the formation of xylulose, while Br nsted acid sites are required to further dehydrate the sugar to furfural. Amberlyst 70 in water/toluene at 175 ℃ showed lower activity but gave a higher furfural yield. Using N2 as the stripping agent considerably improved the furfural yield and product purity in the stripped stream. Catalyst stability was also studied.     

Ni-Ti-O混合氧化物的制备、表征及其富氧选择性催化还原NO

采用均匀共沉淀法制备了不同Ni/Ti摩尔比的Ni-Ti-O混合氧化物,考察了它们在富氧条件下丙烯选择性催化还原NO反应中的催化性能,并运用X射线衍射,N₂吸附-脱附、吡啶吸附、程序升温脱附和原位红外光谱对催化剂进行了表征.结果表明,Ni/Ti摩尔比为1的催化剂表现出最佳催化活性,430℃时NO_x转化率达68%.该催化剂具有锐钛矿结构,比表面积较高(149m²/g),有利于提高催化活性;其表面Lewis酸性位有利于硝酸盐物种的吸附,而硝酸盐物种是该反应的重要中间体.     

Determination of total phosphorus and nitrogen in turbid waters by oxidation with alkaline potassium peroxodisulfate and low pressure microwave digestion, autoclave heating or the use of closed vessels in a hot water bath: comparison with Kjeldahl digestion

The evaluation of the use of alkaline peroxodisulfate digestion with low pressure microwave, autoclave or hot water bath heating for the determination of total phosphorus and nitrogen in turbid lake and river waters is described. The efficiency of these digestion procedures were compared to a Kjeldahl digestion procedure with sulphuric acid-potassium sulfate and copper sulfate. The final solution before digestion was 0.045 M in potassium peroxodisulfate and 0.04 M in sodium hydroxide. Procedures were evaluated by the analysis of suspensions of two reference materials, National Institute of Environmental Science, Japan, no. 3 Chlorella and no. 2 pond sediment and natural turbid waters. Best recoveries of phosphorus and nitrogen by microwave heating were obtained when solutions were digested at 95 °C for 40 min. Quantitative recoveries of phosphorus from Chlorella suspensions up to 1000 mg/l were obtained by all three heating procedures, but incomplete recoveries of nitrogen occurred above 20 mg N/l in the digested sample. Good recoveries of phosphorus and nitrogen from suspended sediment suspensions were obtained only from solutions containing <150 mg/l of suspended sediments. Recoveries of phosphorus from phosphorus compounds containing COP and CP bonds added to distilled water were quantitative (94-113%) except for polyphosphates (microwave, 34±8; autoclave, 114±6; water bath, 96±4) and aluminium phosphate (8-23%). Recoveries of nitrogen compounds containing CN bonds added to distilled water were quantitative (94-96%). The analysis of a range of natural turbid water samples by alkaline peroxodisulfate and microwave, autoclave and water bath heating gave similar total phosphorus and nitrogen results. All procedures using alkaline peroxodisulfate underestimate phosphorus concentrations at high suspended sediment concentrations (>150 mg/l) and are only suitable for the analysis of very turbid samples when the turbidity is due to organic matter (algal cells, plant detritus). Underestimation of nitrogen occurs when samples contain more than 20 mg N/l.     

PAN基活性炭纤维的表面及其孔隙结构解析

通过氮吸附等温线、X射线光电子能谱以及扫描电子显微镜（SEM）对聚丙烯腈（PAN-Polyacrylonitrile）-基活性炭纤维（ACF-Activated Carbon Fiber）的表面和孔隙结构进行了分析,结果表明吸附测量可以提供有关碳质吸附剂的孔结构复杂性;通过XPS对PAN基ACF的表面官能团的种类及含量进行了表征,由SEM对PAN基ACF的表面以及断面的孔隙结构进行了直接观察,提供了有关孔隙结构的直接证据。     

铁改性的Mo/ZSM-5催化剂上NO的选择性催化还原反应

采用浸渍法制备了Mo/ZSM-5, Fe/ZSM-5和不同Fe和Mo摩尔比的Fe-Mo/ZSM-5样品, 并以氨为还原剂对其NO选择性催化还原活性以及反应条件对催化性能的影响进行了研究. 结果表明, Fe-Mo/ZSM-5样品的NOx转化率明显比单独的Mo/ZSM-5和Fe/ZSM-5的高. 当n(Fe):n(Mo)为1.5时, Fe-Mo/ZSM-5样品具有最佳催化性能, 其NOx转化率在430 ℃时达到了96%, 并且能在高空速和不同O2气浓度的条件下保持高的催化活性. 同时采用XRD和XPS技术分别对催化剂的体相结构和表面性质进行了研究, 结果表明, 当n(Fe):n(Mo)=1.5时, Fe和Mo元素之间以及与载体HZSM-5之间存在较强的相互作用, 并且其表面的Mo3d的含量最高. 这可能与其高的催化活性有关. 另外还发现, 在反应过程中Fe-Mo/ZSM-5催化剂表面的氮氧物种主要是吸附态NO, 因此可以推测NO的催化还原反应机理是, 在催化剂表面上, 吸附态NO与吸附NH3物种直接反应生成氮气, 而非经过氧化为NO2的途径.     

N/F掺杂和N-F双掺杂锐钛矿相TiO2(101)表面电子结构的第一性原理计算

采用密度泛函理论(DFT)平面波赝势方法计算了N/F掺杂和N-F双掺杂锐钛矿相TiO2(101)表面的电子结构. 由于DFT方法存在对过渡金属氧化物带隙能的计算结果总是与实际值严重偏离的缺陷, 本文也采用DFT+U(Hubbard 系数)方法对模型的电子结构进行了计算. DFT的计算结果表明N掺杂后, N 2p轨道与O 2p和Ti 3d价带轨道的混合会导致TiO2带隙能的降低, 而F掺杂以及氧空位的引入对材料的电子结构没有明显的影响. DFT+U的计算却给出截然不同的结果, N掺杂并没有导致带隙能的降低, 而只是在带隙中引入一个孤立的杂质能级, 反而F掺杂以及氧空位的引入带来明显的带隙能降低. DFT+U的计算结果与一些实验测量结果能够较好地符合.     

Nitrogen doping in pulsed laser deposited ZnO thin films using dense plasma focus

Pulsed laser deposition synthesized ZnO thin films, grown at 400 °C substrate temperature in different oxygen gas pressures, were irradiated with 6 shots of pulsed nitrogen ions obtained from 2.94 kJ dense plasma focus to achieve the nitrogen doping in ZnO. Structural, compositional and optical properties of as-deposited and nitrogen ion irradiated ZnO thin films were investigated to confirm the successful doping of nitrogen in irradiated samples. Spectral changes have been seen in the nitrogen irradiated ZnO thin film samples from the low temperature PL measurements. Free electron to acceptor emissions can be observed from the irradiated samples, which hints towards the successful nitrogen doping in films. Compositional analysis by X-ray photoelectron spectroscopy and corresponding shifts in binding energy core peaks of oxygen and nitrogen confirmed the successful use of plasma focus device as a novel source for nitrogen ion doping in ZnO thin films.