Strain variation in p-GaN by different spacer layers in the light emitting diodes and their microstructural and emission behaviors

InGaN/GaN multiple quantum well-based blue light emitting diodes (LEDs) with different spacer layer structures were grown by metalorganic chemical vapor deposition. Fast-Fourier-transformed high-resolution transmission electron microscopy was used to determine the influence of the strain status in the spacer layer on Mg distribution and device performance. A comparison of the (1 1¯ 0 0) planar distance showed that the high-temperature grown InGaN layer in the spacer had a high level of stored strain. This led to the formation of a continuous facet contrast induced by Mg segregation in the p-layer, which was responsible for the deterioration of the electroluminescence performance of the LEDs. These results show that the delicate control of stored strain in nitride films is important for improving the device performance.     

A simple method to synthesize α-Si3N4, β-SiC and SiO2 nanowires by carbothermal route

α-Si₃N₄ nanowires, β-SiC nanowires and SiO₂ amorphous nanowires are synthesized via the direct current arc discharge method with a mixture of silicon, activated carbon and silicon dioxide as the precursor. The α-Si₃N₄ nanowires, β-SiC nanowires and SiO₂ amorphous nanowires are about 50–200 nm in stem diameter and 10–100 μm in length. α-Si₃N₄ nanowires and β-SiC nanowires consist of a solid single-crystalline core along the [0 0 1] and [1 1 1] directions, respectively, wrapped within an amorphous SiO_x layer. The direct current arc plasma-assisted self-catalytic vapor–solid and/or vapor–liquid–solid (VLS) growth processes are proposed as the growth mechanism of the nanowires.     

Investigation of void formation beneath thin AlN layers by decomposition of sapphire substrates for self-separation of thick AlN layers grown by HVPE

Void formation at the interface between thick AlN layers and (0 0 0 1) sapphire substrates was investigated to form a predefined separation point of the thick AlN layers for the preparation of freestanding AlN substrates by hydride vapor phase epitaxy (HVPE). By heating 50–200 nm thick intermediate AlN layers above 1400 °C in a gas flow containing H₂ and NH₃, voids were formed beneath the AlN layers by the decomposition reaction of sapphire with hydrogen diffusing to the interface. The volume of the sapphire decomposed at the interface increased as the temperature and time of the heat treatment was increased and as the thickness of the AlN layer decreased. Thick AlN layers subsequently grown at 1450 °C after the formation of voids beneath the intermediate AlN layer with a thickness of 100 nm or above self-separated from the sapphire substrates during post-growth cooling with the aid of voids. The 79 μm thick freestanding AlN substrate obtained using a 200 nm thick intermediate AlN layer had a flat surface with no pits, high optical transparency at wavelengths above 208.1 nm, and a dislocation density of 1.5×10⁸ cm⁻².     

Growth of high quality a-plane GaN epi-layer on r-plane sapphire substrates with optimization of multi-buffer layer

Nonpolar (1 1–2 0) a-plane GaN films have been grown using the multi-buffer layer technique on (1–1 0 2) r-plane sapphire substrates. In order to obtain epitaxial a-plane GaN films, optimized growth condition of the multi-buffer layer was investigated using atomic force microscopy, high resolution X-ray diffraction, and transmission electron microscopy measurements. The experimental results showed that the growth conditions of nucleation layer and three-dimensional growth layer significantly affect the crystal quality of subsequently grown a-plane GaN films. At the optimized growth conditions, omega full-width at half maximum values of (11–20) X-ray rocking curve along c- and m-axes were 430 and 530 arcsec, respectively. From the results of transmission electron microscopy, it was suggested that the high crystal quality of the a-plane GaN film can be obtained from dislocation bending and annihilation by controlling of the island growth mode.     

GaP:Mg layers grown on GaN by MOCVD

We have investigated the growth of magnesium-doped GaP (GaP:Mg) layers on GaN by metalorganic chemical vapor deposition. The hole carrier concentration increased linearly from 0.8×10¹⁸ to 4.2×10¹⁸ cm⁻³ as the Bis(cyclopentadienyl) magnesium (Cp₂Mg) mole flow rate increased from 1.2×10⁻⁷ to 3.6×10⁻⁷ mol/min. However, the hole carrier concentration decreased when the CP₂Mg mole flow rate was further increased. The double crystal X-ray diffraction (DCXRD) rocking curves showed that the GaP:Mg layers were single crystalline at low CP₂Mg molar flow. However, the GaP:Mg layers became polycrystalline if the CP₂Mg molar flow was too high. The decrease in hole carrier concentration at high CP₂Mg molar flow was due to crystal quality deterioration of the GaP layer, which also resulted in the low hole mobility of the GaP:Mg layer.     

Selective etching of dislocations in GaN grown by low-pressure solution growth

This work presents an experimental study on the identification and quantification of different types of dislocations in GaN grown by low-pressure solution growth. A reliable defect selective etching procedure in a NaOH-KOH melt is developed and validated using transmission electron microscopy that permits to define groups of etch pits that belong each to dislocations with a specific Burgers vector. This way a comparably fast method is provided for determining the total, the specific dislocation densities and the type of dislocation in a statistically representative way. The results for the solution grown samples are compared to those obtained for MOCVD GaN.     

Polar dependence of impurity incorporation and yellow luminescence in GaN films grown by metal-organic chemical vapor deposition

We have investigated the unintentional impurities, oxygen and carbon, in GaN films grown on c-plane, r-plane as well as m-plane sapphire by metal-organic chemical vapor deposition. The GaN layer was analyzed by secondary ion mass spectroscopy. The different trend of the incorporation of oxygen and carbon has been explained in the polar (0 0 0 1), nonpolar (1 1 2¯ 0) and semipolar (1 1 2¯ 2) GaN by a combination of the atom bonding structure and the origin direction of the impurities. Furthermore, it has been found that there is a stronger yellow luminescence (YL) in GaN with higher concentration of carbon, suggesting that C-involved defects are originally responsible for the YL.     

Method for modulating the wafer bow of free-standing GaN substrates via inductively coupled plasma etching

The bowing curvature of the free-standing GaN substrate significantly decreased almost linearly from 0.67 to 0.056 m⁻¹ (i.e. the bowing radius increased from 1.5 to 17.8 m) with increase in inductively coupled plasma (ICP) etching time at the N-polar face, and eventually changed the bowing direction from convex to concave. Furthermore, the influences of the bowing curvature on the measured full width at half maximum (FWHM) of high-resolution X-ray diffraction (HRXRD) in (0 0 2) reflection were also deduced, which reduced from 176.8 to 88.8 arcsec with increase in ICP etching time. Decrease in the nonhomogeneous distribution of threading dislocations and point defects as well as V_Ga–O_N complex defects on removing the GaN layer from N-polar face, which removed large amount of defects, was one of the reasons that improved the bowing of the free-standing GaN substrate. Another reason was the high aspect ratio of needle-like GaN that appeared at the N-polar face after ICP etching, which released the compressive strain of the free-standing GaN substrate. By doing so, crack-free and extremely flat free-standing GaN substrates with a bowing radius of 17.8 m could be obtained.     

Optical and electrical properties of Be doped GaN bulk crystals

Highly resistive GaN : Be was obtained by means of synthesis of Ga+Be with atomic nitrogen under high nitrogen pressure. Activation energy of resistivity is about 1.5 eV. This material exhibits features very different from those observed in highly resistive bulk GaN : Mg. Up to 300 K strong yellow band dominates photoluminescence spectrum in resistive GaN : Be crystals. Positron annihilation studies point to the presence of gallium vacancies, V_Ga. In highly resistive GaN:Mg neither yellow band with considerable intensity, nor detectable concentration of V_Ga was found. We also discuss the puzzling findings in highly resistive bulk GaN : Be of morphological features typical for highly conducting bulk n-GaN material.