Active long pulse shaping technique of pulsed CO2 laser using multi-pulse discharge control

We describe the pulse forming of pulsed CO₂ laser using multi-pulse superposition technique. Various pulse shapes, high duty cycle pulse forming network (PFN) are constructed by time sequence. This study shows a technology that makes it possible to make various long pulse shapes by activating SCRs of three PFN modules consecutively at a desirable delay time with the aid of a PIC one-chip microprocessor. The power supply for this experiment consists of three PFN modules. Each PFN module uses a capacitor, a pulse forming inductor, a SCR, a high voltage pulse transformer, and a bridge rectifier on each transformer secondary. The PFN modules operate at low voltage by driving the primary of HV pulse transformer. The secondary of the transformer has a full-wave rectifier, which passes the pulse energy to the load in a continuous sequence.We investigated various long pulse shapes as different trigger time intervals of SCRs among three PFN modules. As a result, we could obtain laser beam with various pulse shapes and durations from about 250 to 1000 μs.     

光纤光栅激光器激射波长的研究

一般认为，用光纤光栅作选频元件的光纤激光器，激射波长与光纤光栅中心反射波长一致，本文报道了不同的实验研究结果。通过细致的实验研究，发现光纤光栅激光器激射波长相对于光纤光栅中心反射波长有一定的偏移。激射波长可以出现在光栅中心反射波长的长波端，也可以出现在其短波端。对不同腔结构的掺镱、掺铒光纤光栅激光器的深入研究证明，谐振腔的各向异性对激光器的激射波长偏移起到决定性的作用，波长最大偏移量主要受限于光纤光栅的反射带宽。通过激光腔内的偏振控制器改变谐振腔的各向异性，可以在光纤光栅的反射带宽内控制激射波长的位置。     

Polytetrafluoroethylene and metal structure convective-flow CO laser

A convective flow CO laser composed of polytetrafluoroethylene discharge tubes, nickel–chromium steel components, a cupric heat exchanger and other components is described. Operating in liquid nitrogen condition, output power of 60 W has been obtained from a non-selective cavity.     

Long-wavelength light emission from InAs quantum dots covered by GaAsSb grown on GaAs substrates

We fabricated InAs quantum dots (QDs) with a GaAsSb strain-reducing layer (SRL) on a GaAs(0 0 1) substrate. The wavelength of emission from InAs QD is shown to be controllable by changing the composition and thickness of the SRL. An increase in photoluminescence intensity with increasing compositions of Sb and thickness of the GaAsSb SRL is also seen. The efficiency of radiative recombination was improved under both conditions because the InAs/GaAsSb/GaAs hetero-interface band structure more effectively suppressed carrier escape from the InAs QDs.     

Electron–hole complexes in self-assembled quantum dots in strong magnetic fields

We present results of calculations and experiments on electron–hole complexes in InGaAs/GaAs self-assembled quantum dots in high magnetic field (B). Due to hidden symmetries, the chemical potential of an N-exciton system at special B fields becomes insensitive to the exciton number as well as the magnetic field. This results in plateau regions of high intensity in measured magneto-PL spectrum. Theoretical calculations using exact diagonalization techniques successfully explain the measured magneto-photoluminescence spectrum with B fields up to 28 T.     

Cochran's statistical theorem for outer inverses of matrices and matrix quadratic forms

We extend the matrix version of Cochran's statistical theorem to outer inverses of a matrix. As applications, we investigate the Wishartness and independence of matrix quadratic forms for Kronecker product covariance structures.     

电子束流品质对自由电子激光小信号增益影响的计算

对电子束有一定初始能量分散或角度分散时的自由电子激光小信号增益用较简便的方法进行了分析计算,并给出了一个渐近公式,结果与用计算机模拟解自由电子激光微分方程组得到的结果一致。     

New FIR laser lines and frequency measurements for optically pumped CD3OH

Twenty new cw FIR laser lines in CD₃OH, optically pumped by a CO₂ laser, are reported. The frequencies of 39 of the stronger laser lines were measured relative to stabilized CO₂ lasers with a fractional uncertainty, as determined by the reproducibility of the FIR frequency itself, of 2 parts in 10⁷.Contribution of the U.S. Government, not subject to copyright.     

X-Ray Mapping and Interpretation of Scatter Diagrams

Electron beam induced quantitative X-ray mapping has become a very useful characterisation tool for determining the elemental distribution in materials, whether using energy dispersive spectroscopy or wavelength dispersive spectroscopy. The X-ray intensity distributions of the elements from an X-ray map allow us to generate two dimensional and ternary scatter diagrams thus converting spatial information into concentration dimensions, which is an important tool for displaying the spatial relationships of elements or correlated elements (phases) in materials. To best understand how to use this tool, we need to understand the production and features of the scatter diagram. The type of clustering observed in the scatter diagram, whether oval, linear or spherical, can give the major and trace element distributions within phases as well as qualitative and quantitative phase information. This paper demonstrates the generation of scatter diagrams, properties of scatter diagrams, interpretation of scatter diagrams and the advantages of scatter diagrams through the use of examples.