Development of nanocrystalline Mn-Zn ferrites for high frequency transformer applications

Microwave-Hydrothermal (M-H) method has been successfully used for the synthesis of nanocrystalline Mn-Zn ferrites which are used for high-frequency applications. As synthesized powders were characterized using X-ray diffraction (XRD) and transmission electron microscopy (TEM). The nanopowders were annealed at 600 °C/20 min using the microwave sintering method. The frequency dependence of dielectric constant (ε′) was measured in the range of 10 Hz-1.3 GHz and initial permeability (μ_i) was measured in the range of 10 Hz-1 MHz. The total power loss (P_t) was measured on the annealed samples at 100 kHz and 200 mT condition. Conductor-embedded-ferrite transformers were fabricated and output power (P_o), efficiency (η) and temperature rise (ΔT) were measured at sinusoidal voltage of 25 V at 1 MHz. The transformer efficiency (η) was found to be high and surface rise of temperature (ΔT) is very low.     

Nanocrystalline nickel films with lotus leaf texture for superhydrophobic and low friction surfaces

Nanostructured Ni films with high hardness, high hydrophobicity and low coefficient of friction (COF) were fabricated. The surface texture of lotus leaf was replicated using a cellulose acetate film, on which a nanocrystalline (NC) Ni coating with a grain size of 30 ± 4 nm was electrodeposited to obtain a self-sustaining film with a hardness of 4.42 GPa. The surface texture of the NC Ni obtained in this way featured a high density (4 × 10³ mm⁻²) of conical protuberances with an average height of 10.0 ± 2.0 μm and a tip radius of 2.5 ± 0.5 μm. This structure increased the water repellency and reduced the COF, compared to smooth NC Ni surfaces. The application of a short-duration (120 s) electrodeposition process that deposited “Ni crowns” with a larger radius of 6.0 ± 0.5 μm on the protuberances, followed by a perfluoropolyether (PFPE) solution treatment succeeded in producing a surface texture consisting of nanotextured protuberances that resulted in a very high water contact angle of 156°, comparable to that of the superhydrophobic lotus leaf. Additionally, the microscale protuberances eliminated the initial high COF peaks observed when smooth NC Ni films were tested, and the PFPE treatment resulted in a 60% reduction in the steady-state COFs.     

The effects of temperature on nanocrystalline diamond films deposited on WC-13 wt.% Co substrate with W-C gradient layer

A tungsten-carbide gradient coating (WCGC) was prepared by reactive sputtering as an intermediate layer on the cemented carbide, WC-13 wt.% Co, substrate to improve the nucleation, smoothness and adhesion of diamond film. The diamond film was deposited by hot filament chemical vapor deposition (HFCVD). The effects of the substrate temperature on the WCGC and the diamond film were investigated. The characterization of the WCGC and the diamond films was analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), micro-Raman spectroscopy and Rockwell hardness indentation. It is found that the WCGC plays an important role in improving the nucleation, smoothness and adhesion of diamond film; and the diamond films exhibit better quality and adhesion as substrate temperature increases during the CVD processes.     

����Ƶ�ŵ�������׹象Ĥ�����ٶȵĻ����о�

建立一维自洽流体模型,对低压甚高频等离子体放电中产生的主要粒子建立连续性方程、动量方程和电流平衡方程。分析了甚高频对纳米粒子的种子离子SiH3-及电子和正离子SiH3+的影响,给出了种子离子、电子以及正离子密度随频率变化的时空演化过程。结果表明改变频率可以改变SiH3-的密度,从而控制粒子的成核及生长。同时甚高频放电也改变了等离子体中电子和正离子密度以及电场的强度,从而加快等离子体中的化学反应速度和纳米粒子的沉积速度。       

纳米ZnO薄膜的光致发光性质

利用溶胶－凝胶法制备了纳米ZnO薄膜,室温下测量了样品的光致发光谱(PL)、吸收谱(ABS)、X射线衍射谱(XRD)．X射线衍射(XRD)的结果表明：纳米ZnO薄膜呈多晶状态,具有六角纤锌矿晶体结构和良好的C轴取向．观察到二个荧光发射带,中心波长分别位于395 nm的紫带、524 nm的绿带和450 nm附近的蓝带．证实了纳米ZnO薄膜绿光可见发射带来自氧空位(VO)形成的浅施主能级和锌空位(VZn)形成的浅受主能级之间的复合;450 nm附近的蓝带来自电子从VO的浅施主能级到价带顶或锌填隙(Zni) 到价带顶或导带底到VZn的浅受主能级的复合．     

Sol–gel synthesis and characterization of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–TiO<Subscript>2</Subscript> nanocrystalline powder

Al₂O₃–TiO₂ nanocrystalline powders were synthesized by sol–gel process. Aluminum sec-butoxide and titanium isopropoxide chemicals were used as precursors and ethyl acetoacetate was used as chelating agent. Thermal and crystallization behaviors of the precursor powders were investigated by thermal gravimetric-differential thermal analysis, Fourier-transform infrared spectrum and X-ray diffraction. The average crystalline size of heat treated Al₂O₃–TiO₂ powders at 1,100 °C is ~100 nm.     

Graphite/Nanocrystalline Zeolite Platform for Selective Electrochemical Determination of Hepatitis C Inhibitor Ledipasvir

A simple and efficient procedure is described for the electrochemical determination of ledipasvir (LDP) in presence of co‐formulated drug sofosbuvir (SOF). Herein, a highly sensitive, low‐cost electrochemical protocol was utilized to fabricate a zeolite modified carbon paste electrode (ZY/CPE) through mixing of zeolite nanostructures with graphite powder. The fabricated sensor displayed high sensitivity, allowing optimal charge transfer/electrode kinetics. Different experimental and chemical factors, including electrode composition, effect of pH, scan rate and amount of ZY were evaluated carefully to obtain the highest electrochemical response. Under optimized conditions and using square wave voltammetry (SWV), the current response of the ZY/CPE electrochemical sensing platform exhibited a detection limit of 7.5×10^?9 M and a large linear range from 5.0×10^?8 to 1.0×10^?4 M. The practical applicability of the suggested electrochemical platform was verified in the assessment of LDP in pharmaceutical formulations with excellent recoveries in the range of 99.50–98.87 %. Moreover, a biological relevance of the developed sensor was established by the analysis of LDP in human urine and plasma samples with satisfactory recoveries of 99.00 and 99.68 %, respectively. Due to the simplicity and ease of preparation of the proposed sensor, it can be used in quality control laboratories and for clinical analysis.     

Electrochemical Sensor Platforms Based on Nanostructured Metal Oxides,and Zeolite‐Based Materials

Electrochemical sensors have drawn significant attention over the last couple of decades because of their ability to improve detection of organic and inorganic analytes found in the field of biotechnology, environmental sciences, medicine, and food quality control. This personal account summarizes the state‐of‐art research carried out in the construction and evaluation of nanostructured metal oxides and zeolite based electrochemical sensors. Metal oxides and zeolite‐based nanomaterials have many unique and extraordinary properties such as tunable redox activity, surface functionalization ability, optimum conductivity, large surface area, biocompatibility and so forth. In this personal account, the current advances in electrochemical sensor applications of metal oxides, zeolite‐based nanomaterials, and their nanocomposites are described for the single and simultaneous determination of organic & inorganic contaminants present in water bodies, physiological bio‐molecules present in human blood & urine samples, and organic contaminants present in food materials.Moreover, concluding section focuses discussion on the future developments and applications of these materials in various emerging technologies.     

Lead telluride nanocrystalline thin films: Structure,optical characterization and a broadband dielectric spectroscopy study

Nanocrystalline PbTe thin films were deposited on a glass substrate by thermal evaporation technique with two thicknesses namely, 45 and 250 nm. The structural studies revealed that the films have nanocrystalline cubic structure and the particle size was found to be 11 and 20.7 nm, for low and high thicknesses respectively. The FE-SEM study shows that the surface grains increase for higher thickness film. This indicates that samples lying under the strong regime of confinement for PbTe thin films. The optical properties confirm the occurrence of confinement process as the optical band gap are 1.67 and 0.9 eV for 45 and 250 nm films, respectively. The dielectric results indicated that the conductivity increases by about two orders of magnitude with increasing the thickness from 45 to 250 nm. Moreover, the permittivity shows a higher dispersion step at lower frequencies in both samples due to the hopping conduction mechanism in addition to the interfacial polarization in such heterogeneous structures. Another small dispersion step is noticed in case of the lower thickness. It is attributed to the polarization of the accumulated charge carriers near the grain boundaries interfaces. No indication of any electrode phenomena in both samples is shown here.     

Light emissions from a silicon nanocrystal thin film prepared by phase separation of hydrogen silsesquioxane

We report a facile method to prepare thin film of Si nanocrystals embedded SiO₂ (Si-NC:SiO₂) by annealing a photoresist of hydrogen silsesquioxane (HSQ) at 1100 °C in nitrogen via a phase separation process. The spatial density, photoluminescence intensity, the photoluminescence efficiency and electroluminescence intensity of Si-NC of the sample made from HSQ, or HSQ sample, were 15.0, 5.5, 1.5 and 7.9 times as large as those of the sample made by a traditional method of annealing SiO_x (1<x<2), or SiO_x sample, respectively. Meanwhile, the turn-on voltage of electroluminescence of the HSQ sample was only 3.8 eV, which was more than 2 times smaller than that of the SiO_x sample. The results of this work may find application in developing high brightness Si light sources.