Pt微粒修饰纳米纤维聚苯胺电极对甲醇氧化电催化

以脉冲电流法制备的纳米纤维状聚苯胺(PANI)为Pt催化剂载体，用它制备了甲醇阳极氧化的催化电极Pt/（nano-fibular PANI）.研究结果表明, Pt/（nano-fibular PANI）电极对甲醇氧化具有很好的电催化活性,并有协同催化作用.在相同的Pt载量条件下， Pt/（nano-fibular PANI）电极比Pt微粒修饰的颗粒状聚苯胺电极Pt/(granular PANI)具有更好的电催化活性.此外， Pt的电沉积修饰方法同样影响Pt/（nano-fibular PANI）电极对甲醇氧化的催化活性.脉冲电流法沉积Pt形成的复合电极较循环伏安法电沉积得到的Pt复合电极具有更优异的催化活性.     

累托石/聚丙烯插层纳米复合材料的制备与性能

采用熔融共混法制备了有机改性累托石 (OREC)粘土 均聚聚丙烯 (PP)纳米复合材料 ,以X 射线衍射分析 (XRD)及透射电子显微镜分析 (TEM)观察了复合材料的相貌结构 ,研究了复合材料的力学性能及热性能 .结果表明 ,OREC在添加份数较少时可与均聚聚丙烯熔融插层形成插层型聚丙烯纳米复合材料 ,该复合材料与纯PP相比 ,具有较高的拉伸强度、断裂伸长率及冲击强度 .在有机粘土添加 2 %时 ,复合材料的拉伸强度、断裂伸长率、冲击强度最高 ,与纯PP相比 ,2 %添加量的聚丙烯纳米复合材料拉伸强度提高 6 5 7% ,断裂伸长率提高 2 89 3% ,冲击强度提高 14 1% ,10 %失重率时对应的热分解温度提高 50K .     

IR STUDIES OF THE THERMAL DECOMPOSITION OF[Rh_6(CO)_(16) Co_4(CO)_(12)]/SiO_2: EVIDENCE FOR THE FORMATION OF RhCo_3(CO)_(12)/SiO_2

IntroductionThepreparativeapproachofaneffectivebilTldslliccatalystisalwaysasubjectofboortantsignificanceinheterogeneouscatalysis.InourrecentstUdies,wefoundthatthebAnetallitcarbonylclustercoCo3(CO)12favorablygivesthebAnetalliccoCo3clusterontheSiOZsubdueaft…     

Liquid-Phase Selective Oxidation of Propane on Silica-Supported Nafion Catalysts

The liquid-phase partial oxidation of propane in the presence of the Fen+/H2O2 Fenton system at 70℃ and 1.4 atm on silica supported Nafion catalysts has been investigated. The reaction proceeds via a radical reaction path the efficiency of which is improved by silica-supported Nafion catalysts. Because of the direct relationship between reaction rate and concentration of sulphonic acid sites of Nafion catalysts, it is inferred that the active phase enahnces the kinetics of propane conversion by promoting the rate of active radicals generation.     

Ethanol Washing Effect on Textural Properties of the Sodium Silicate-Derived Silica Xerogel

This study deals with the use of ethanol as washing solvent in the preparation of the silica gels from sodium silicate in order to enhance the textural properties, especially surface area. We here examined the effect of ethanol-washing on surface area, micro- and mesopore volume, and average pore size. The silica xerogels prepared from sodium silicate solution exhibited an extremely high surface area of 1139 m2/g by washing their hydrogels with ethanol. Compared to water-washed xerogels, ethanol-washed xerogels showed higher surface areas, total pore volumes, and larger average pore sizes. Unlike the surface area of water-washed xerogel, that of the ethanol-washed xerogel was not affected by the silica concentration of initial solution. This study indicates that the textural properties of sodium silicate-derived xerogels are further enhanced by using ethanol as washing solvent.     

FIA-ICP/AES法分析茶叶浸取液中多元素的形态

本文报道了分析茶叶浸取液中[Zn、Mn、Fe、Al及Mg]形态的新方法。研究了以C-18柱为分离柱的流动注射与ICP/AES的联用技术。     

Dissipative structures formed in the course of drying the colloidal crystals of silica spheres on a cover glass

Macroscopic and microscopic dissipative structural patterns formed in the course of drying the deionized aqueous colloidal crystal suspensions of silica spheres (diameter: 103 nm) on a cover glass have been observed. Spoke-like and ring-like patterns are formed in the macroscopic scale; the former is the crack in the sphere film and the latter is the hill accumulated with spheres formed around the outside edge. The neighbored inter-spoke angle, thickness of the film, and other morphological parameters have been discussed as a function of sphere concentration, concentration of sodium chloride, and the inclined angle of the cover glass. Fractal patterns of the mud cracks are observed in the microscopic scale. Capillary forces between spheres at the air-liquid surface and the relative rates between the water flow at the drying front and the convection flow of spheres are important for the pattern formation. Electronic Publication     

Rapid determination of organochlorine pesticide residues in feeds by capillary gas chromatography

A simple micro-method is described for determination of 15 organochlorine pesticide residues in mixed feeds. Clean-up of the petroleum ether extract is by basic alumina minicolumn chromatography and quantitative identification is by capillary gas chromatography with electron capture detection. Cyanopropyl-polysiloxane chemically bonded fused silica capillary columns have been used to perform high resolution analyses in short time as well as to overcome possible interferences by PCBs. Recovery, repeatability, and detection limits of the proposed procedure are checked and results are also reported for non random samples of 180 feeds collected in Italy.     

A critical reappraisal of recent communications on the hydrodynamic characterization of silica (aerosil) hydrosols

Different results from recent communications on the hydrodynamic characterization of ultrasonicated silica (®Aerosil) hydrosols led to a critical reappraisal of the data.It can be concluded that the degree of dispersion achievable in pyrogenic (Aerosil) hydrosols by ultrasonication is highly sensitive to the detailed parameters of the dispersion process. Characterization in terms ofabsolute numbers of a limiting particle morphology, corresponding to minima of aggregate size, porosity and number of primary particles in the aggregate is not possible.The most straightforward approach for hydrodynamic characterization seems to be a combination of sedimentation and diffusion data.Other approaches using a combination of sedimentation and viscosity data underestimate the particle dimensions. Moreover, they are quite arbitrary since the final result depends upon the proper choice between several equations for fitting the viscosity concentration dependence; the most rigorous approach seems to be an extended Einstein equation which has recently been adapted to particle aggregates.     

Thermal decomposition of surface compounds for the generation of small quantities of acetaldehyde: Calibration of a thermal desorption-gas chromatography-flame ionization detection

The paper presents a new method for the generation of acetaldehyde in the amounts that allow to calibrate the measuring system. The method is based on thermal decomposition of surface compounds at the range 130-190 °C, in which an acetaldehyde as the decomposition product is released. The synthetic pathway leading to the desired surface compounds is described. Investigations demonstrated that the synthesis of the compounds on the surface of the support material (silica gel) was carried out homogeneously. The technique proposed was used for the generation of gaseous standard mixtures containing acetaldehyde for the calibration of a thermal desorber-gas chromatograph-flame ionization detector system.