光参量啁啾脉冲饱和放大的增益稳定性

 光参量啁啾脉冲放大（OPCPA）在饱和放大区存在一个增益稳定点，据此设计了一个输出稳定的三级OPCPA系统；第一、二、三级分别选用准相位匹配的周期极化钛氧磷酸钾（PPKTP）晶体、LBO晶体和KDP晶体作为增益介质。饱和放大时，增益随泵浦光强度变化时的增益输出稳定性明显改善，在泵浦光强度抖动低于6%的情况下，各级光参量放大器OPA输出的增益抖动小于1%。前级采用准相位匹配的PPKTP晶体作为增益介质，在远低于破坏阈值的30MW/cm²的泵浦功率密度下，可得到2×10⁵的饱和放大增益和20%的能量转换效率。     

介质靶表面的充电效应对等离子体浸没离子注入过程中鞘层特性的影响

针对等离子体浸没离子注入技术在绝缘体表面制备硅薄膜工艺，采用一维脉冲鞘层模型描述介质靶表面的充电效应对鞘层厚度、注入剂量及靶表面电位等物理量的影响.数值模拟结果表明：随着等离子体密度的增高，表面的充电效应将导致鞘层厚度变薄、表面电位下降以及注入剂量增加，而介质的厚度对鞘层特性的影响则相对较小. 关键词： 等离子体浸没离子注入 脉冲鞘层 绝缘介质 充电效应     

超短脉冲超强激光与固体靶相互作用中高能离子的产生

 用2D3V PIC粒子模拟方法得到了超短脉冲超强激光与固体靶相互作用中高能离子产生的图像，并对其机理进行了研究。在靶前后表面都观察到了高能离子的产生，并诊断了离子能谱。模拟结果表明，在靶前表面所产生的高能离子，角分布较大，在向靶内输运过程中会损失能量；在靶后表面产生的高能离子，定向性很好，能获得很高的能量。模拟得到的离子能量和实验观测结果在量级上相符。     

高速色散补偿系统中喇曼放大器性能研究

利用喇曼放大器的非线性偏微分耦合方程组,对带喇曼放大器的色散补偿系统进行了仿真,并与传统的仿真方法进行了比较.结果表明:在色散完全补偿系统中,当传输速率较高时,忽略色散后的传统仿真方法的结果,与采用色散补偿技术后使整个系统色散为零的仿真结果有一定偏差,此时不能忽略色散的作用.还对前补偿系统和后补偿系统进行了研究,利用Q值性能判别法,分别得到了信号光脉冲的最佳占空比和最佳脉冲阶数.     

Picosecond control of coherent magnetisation dynamics in permalloy thin films by picosecond magnetic field pulse shaping

We have measured the response of a 20×10 μm, 8 nm thin NiFe (80:20) permalloy film due to excitation by short in-plane magnetic field pulses. We will show that using a two-pulse-technique a complete control of the precessional motion of the magnetisation can be achieved on picosecond timescales. Furthermore, we will present numerical calculations which show that a complete suppression of magnetisation ringing after switching can only be realised by a cascade of short field pulses.     

高功率飞秒脉冲激光器的进展

概述了超短激光脉冲技术发展的历程。详尽的论述了啁啾脉冲放大技术的原理和一些关键技术 ,并对当今飞秒激光器研究发展的状况进行了综述。在分析其应用前景的基础上 ,进一步指出了这一技术领域未来的发展趋势。结果表明 ,脉冲激光放大系统以后的发展方向是 :更短脉冲 ;追求更高峰值功率 ;连续光谱调谐化 ;向小型化乃至全光纤化发展。     

高功率横流CO2激光器脉冲预电离过程研究

本文给出了对高功率横流CO_2激光器脉冲预电离过程的理论和实验研究.表明了预电离过程中光电离的重要作用.实验结果表明,脉冲预电离可增大高功率横流CO_2.激光器的pd值(p为放电气压、d为放电间隔),增大放电区注入功率密度.对于提高此类型激光器的放电稳定性和输出激光功率是一种技术简单而有效的手段.     

Obtaining 4-vinylphenols by decarboxylation of natural 4-hydroxycinnamic acids under microwave irradiation

4-Vinylphenols, useful compounds for industrial applications, were obtained by decarboxylation of 4-hydroxycinnamic acids under microwave irradiation in the presence of 1,8-diazabicyclo[5.4.0]undec-7-ene (DBU) as base and basic aluminum oxide as solid support. The reactions were fast (15-30 min). The selective extraction of the final products with ethyl acetate avoids chromatographic purifications. The conversions are quantitative and the yields are satisfactory. Only the unstable 4-vinylcatechol was obtained in moderate yield. This procedure was successfully extended to a natural sample of ferulic acid extracted from wheat bran to get the corresponding 4-vinylguaiacol, a FEMA GRAS (Flavor and Extract Manufacturer's Association; General Regarded as Safe) approved flavoring agent.     

微波消解ICP-AES法同时测定花岗石中铜、镉、铬和砷

本文采用微波消解和ICP－AES法，同时测定花岗石样品的铅、镉、铬、砷4有害元素，检出限分别为0．0008、0．0007、0．0018、0．0012μg.mL^-1,回收率为93．4％－102．5％，RSD为1．3％－3．6％，该法准确、快速、简便，结果令人满意。     

Property improvement of pulsed laser deposited boron carbide films by pulse shortening

Growth characteristics and surface morphology of boron carbide films fabricated by ablating a B₄C target in high vacuum with a traditional KrF excimer laser and a high brightness hybrid dye/excimer laser system emitting at the same wavelength while delivering 700 fs pulses are compared. The ultrashort pulse processing is highly effective. Energy densities between 0.25 and 2 J cm⁻² result in apparent growth rates ranging from 0.017 to 0.085 nm/pulse. Ablation with nanosecond pulses of one order of magnitude higher energy densities yields smaller growth rates, the figures increase from 0.002 to 0.016 nm/pulse within the 2-14.3 J cm⁻² fluence window. 2D thickness maps derived from variable angle spectroscopic ellipsometry reveal that, when ablating with sub-ps pulses, the spot size rather than the energy density determines both the deposition rate and the angular distribution of film material. Pulse shortening leads to significant improvement in surface morphology, as well. While droplets with number densities ranging from 1 × 10⁴ to 7 × 10⁴ mm⁻² deteriorate the surface of the films deposited by the KrF excimer laser, sub-ps pulses produce practically droplet-free films. The absence of droplets has also a beneficial effect on the stoichiometry and homogeneity of the films fabricated by ultrashort pulses.