Sol-Gel Particulate Float Process to Make Vitreous Silica Bodies

Particulate sol-gel technology uses larger particles than that of alkoxide-derived gels and provides larger pore sizes in the gelled object. This allows relatively rapid drying and fabrication of large rods or tubular shapes. However, the formation of more complex or flat shapes, which require extensive surface contact with a mold, is more difficult. The shrinkage during drying, with the significantly greater stress of surface friction due to adhesion, frequently leads to cracking.We have demonstrated a solution to this problem by floating the gel on the surface of a dense liquid. Dry silica panels up to 28 × 40 × 0.7 cm³ were prepared in this way. The use of patterning molds allowed the fabrication of more sophisticated shapes. These bodies were sintered to transparent vitreous silica articles of near net dimensions.     

Molecular modeling study on surface,thermal, mechanical and gas diffusion properties of chitosan

The motivation of this work is to provide reliable and accurate modeling studies of the physical (surface, thermal, mechanical and gas diffusion) properties of chitosan (CS) polymer. Our computational efforts have been devoted to make a comparison of the structural bulk properties of CS with similar type of polymers such as chitin and cellulose through cohesive energy density, solubility parameter, hydrogen bonding, and free volume distribution calculations. Atomistic modeling on CS polymer using molecular mechanics (MM) and molecular dynamics (MD) simulations has been carried out in three dimensionally periodic and effective two dimensionally periodic condensed phases. From the equilibrated structures, surface energies were computed. The equilibrium structure of the films shows an interior region of mass density close to the value in the bulk state. Various components of energetic interactions have been examined in detail to acquire a better insight into the interactions between bulk structure and the film surface. MD simulation (NPT ensemble) has also been used to obtain polymer specific volume as a function of temperature. It is demonstrated that these V–T curves can be used to locate the volumetric glass transition temperature (T_g) reliably. The mechanical properties of CS have been obtained using the strain deformation method. Diffusion coefficients of O₂, N₂, and CO₂ gas molecules at 300 K in CS have been estimated. The calculated properties of CS are comparable with the experimental values reported in the literature. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1260–1270, 2007     

Effect of nanotube functionalization on the properties of single‐walled carbon nanotube/polyurethane composites

A commercially available aliphatic thermoplastic polyurethane formulated with a methylene bis(cyclohexyl) diisocyanate hard segment and a poly(tetramethylene oxide) soft segment and chain‐extended with 1,4‐butanediol was dissolved in dimethylformamide and mixed with dispersed single‐walled carbon nanotubes. The properties of composites made with unfunctionalized nanotubes were compared with the properties of composites made with nanotubes functionalized to contain hydroxyl groups. Functionalization almost eliminated the conductivity of the tubes according to the conductivity of the composites above the percolation threshold. In most cases, functionalized and unfunctionalized tubes yielded composites with statistically identical mechanical properties. However, composites made with functionalized tubes did have a slightly higher modulus in the rubbery plateau region at higher nanotube fractions. Small‐angle X‐ray scattering patterns indicated that the dispersion reached a plateau in the unfunctionalized composites that was consistent with the plateau in the rubbery plateau region. The room‐temperature modulus and tensile strength increase was proportionally higher than almost all increases seen previously in thermoplastic polyurethanes; however, the increase was still an order of magnitude below what has been reported for the best nanotube–polymer systems. Nanotube addition increased the hard‐segment glass transition temperature slightly, whereas the soft‐segment glass transition was so diffuse that no conclusions could be drawn. Unfunctionalized tubes suppressed the crystallization of the hard segment; whereas functionalized tubes had no effect. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 490–501, 2007     

Thickness dependence of free‐standing thin films

Below a critical thickness, of about 60 nm, the glass transition temperature of polystyrene (PS) films decreases with film thickness, as demonstrated using free‐standing films. A geometrical model is developed here describing this phenomenon in the case of ideal (Gaussian) chains. This model, which can be considered as an application of the free volume model, assumes that the decrease of the glass transition temperature from thick to ultrathin films is due to the modification of the interpenetration between neighboring chains. The theoretical curve deduced from the model is in excellent agreement with the PS experimental results, without using any adjustable parameters. From these results, it can be concluded that new chain motions, usually buried in bulk samples, are expressed by the presence of the surface. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 10–17, 2007     

Optical properties of a high-efficiency glass ceramic X-ray storage phosphor

The turbidity, photoluminescence, and photo-stimulated luminescence (PSL) of fluorozirconate glass containing barium chloride nano- and micro-crystals have been measured for samples prepared by isochronal (70 min) annealing over a temperature range of 220–283°C, and correlated with the microstructure as determined by X-ray diffraction measurements. Crystallization of hexagonal phase barium chloride commences at around 220°C, but until 275°C the material retains excellent transparency although it displays negligible PSL. Between 275°C and 277°C, the hexagonal phase converts to the orthorhombic phase, the transparency abruptly decreases, and the PSL rises to a value of around 13% of that found for the commercial storage phosphor BaFBr:Eu. For a slightly higher temperature of 280°C, new phases appear which correspond to the onset of bulk crystallization, and at 283°C the relative PSL rises to 33%, while the transparency falls further. The trade-off between optical transparency and PSL over this narrow temperature window for X-ray imaging plate applications is briefly discussed.     

利用计算机辅助装调检测矩形大口径离轴非球面的方法研究

通过非球面的零位补偿法,完成了对矩形大口径离轴非球面镜的检测。先用光学设计软件Zemax从理论上分析了在检测中会出现的现象,并结合计算机辅助装调技术,确定在检测过程中相对敏感的自由度,然后控制这些量,使补偿器和非球面的相对关系与理论设计相吻合,在Zygo相位干涉仪上测得最终结果。在λ=632.8nm时,中心圆口径与两个边缘圆口径面形误差RMS分别为0.022λ,0.037λ,0.032λ。检测结果,达到预期目的。     

新型菲涅尔线聚焦聚光太阳电池组件研究

以聚甲基丙烯酸甲脂为材料,采用热压成型工艺加工成型线聚焦菲涅尔聚光透镜(8×),可用于空间、地面光伏系统太阳电池组件的聚光系统,并对在其聚光条件下,太阳电池的电流电压特性进行测试,结果表明,该菲涅尔线聚焦棱镜能有效提高太阳电池的单位输出功率.模具的机械加工精度和光学抛光精度低,是造成其部分聚光率损失的原因.     

Radiation heat transfer in axisymmetric quartz glass tubes

A mathematical model is proposed to describe the heat transfer in quartz glass axisymmetric tubes. Heat is transferred inside the glass by radiation and conduction. Scattering of thermal radiation inside the glass is ignored. At the boundaries of the tube the radiative intensity is specularly reflected. The spectral dependent radiative intensity and the temperature distribution inside the tube are determined. The model is applied to simulate the cooling process of a quartz glass tube. The calculated temperature is in agreement with that obtained from an experiment. Furthermore, steady-state temperature distributions in quartz glass tubes of different lengths have been determined.     

Computational Electrochemistry: A Model to Studying Ohmic Distortion of Voltammetry in Multiple Working Electrode,Microfluidic Devices,an Adaptive FEM Approach

Characteristics of mass transport and potential distribution applicable to microfluidic electrochemical flow cell devices has been modelled using the finite element method. A flexible, automatic grid generation algorithm has been combined with an a‐posteriori error indication technique presented by Nann and Heinze to allow irregular cell geometries to be modelled. The code has been applied to the problem of steady state generator – detector linear sweep voltammetry in a channel flow cell showing the effects of IR drop on the voltammetric response of each electrode.     

扫描力显微术在高聚物薄膜玻璃化转变研究中的应用

简述了高聚物薄膜玻璃化转变的复杂性，并结合文章作者的的一些研究结果介绍了扫描力显微术(SFM)在研究高聚物玻璃化转变中的一些方法，包括观察高聚物薄膜形貌的变化，测量其摩擦力、粘附力和弹性模量等物理量的变化，最后指出SFM是研究高聚物薄膜玻璃化转变的有力工具。