Study of formation of nano-quasicrystals and crystallization kinetics of Zr-Al-Ni-Cu metallic glass

The formation of nano-quasicrystals on isothermal annealing of melt-spun ribbons of Zr_69.5Al_7.5Ni₁₁Cu₁₂ metallic glass has been investigated using transmission electron microscopy (TEM). The crystallization study of this metallic glass has been carried out using differential scanning calorimetry (DSC) in non-isothermal (linear heating) mode. It exhibits two-stage crystallization where the first stage corresponds to the precipitation of icosohedral nano-quasicrystalline phase. This has been confirmed with the help of TEM investigations. The crystallization parameters like the activation energy (E _c) and frequency factor (k ₀) have been derived using the Kissinger peak shift analysis. The activation energies for the first and second crystallization peak are found to be 278 and 295 kJ mol^–1, respectively. The frequency factors obtained for the two peaks are respectively 7.16·10¹⁹ and 1.42·10²⁰ s^–1. E _c, k ₀ and the Avrami exponent (n) have also been derived by fitting the Johnson-Mehl-Avrami-Kolmogorov (JMAK) equation for the transformed volume fraction (x) to the crystallization data. JMAK results of E _c for the first and second crystallization peak turn out to be 270 and 290 kJ mol^–1 respectively. However, k ₀ and n are found to be heating rate dependent as reported in similar studies. The values of n for the first crystallization stage ranges between 1.66 and 2.57 indicating diffusion-controlled transformation in agreement with earlier reports.     

微孔中简单流体粘度的分子动力学模拟及关联模型

用分子动力学模拟计算了微孔介质中流体氩在不同温度、不同密度和不同孔径下的剪切粘度.并根据Chapman-Enskog关于硬球流体传递性质的理论以及Heyes的关于Lennard-Jones流体粘度的表达式,提出了两个描述微孔介质中流体粘度的模型,该模型可以计算微孔中流体氩在不同状态下的粘度值.通过与计算机模拟值的比较,证明这两个微孔流体粘度模型是可用的.     

光谱电化学法研究亚甲基蓝的电还原反应

用极谱法研究亚甲基蓝(MB)的电极吸附过程早有报道.近几年,用光谱电化学法研究其电化学行为又引起了许多人的兴趣.但在光透薄层电极上,由于光程太短,测试溶液浓度较高,导致亚甲基蓝发生聚合,影响实验结果的准确测定.为此本文利用特制的比色皿型长光程薄层光谱电化学池,在低浓度条件下研究其在SnO_2镀膜玻璃电极上的电还原反应.     

Effect of solvent on glass transition temperature in chemically modified polyvinyl chloride (PVC)

Polyvinylchloride has been chemically modified with sodium benzene thiolate at different temperatures, in solvents promoting the formation of polymer gels, in solvents favoring light polymer interactions and in the absence of solvent, that is, in the melt. From the¹³C-NMR results it is shown that the substitution reactions on PVC, in all media and temperatures studied, are stereospecific and the nature of substituted chlorines the same.The glass transition temperature of modified polymers has been studied by differential scanning calorimetry. The glass transition temperature of the modified polymers in the absence of solvent decreases linearly with degree of substitution. When the reaction is carried out in solvents containing carbonyl groups, such as diethyl malonate, cyclohexanone and 2-butanone, the evolution of the glass transition up to about 25% substitution does not follow the above behavior. At higher levels of substitution the evolution ofT _g is similar to that in the melt. For the ether-containing solvents, such as tetrahydrofurane and dioxane, the evolution lies between the two previous curves.When the reactions of PVC with sodium benzene thiolate are carried out in cyclohexanone at different temperatures, between 15–90°C, the evolution of the glass transition temperature with conversion is different for each temperature, and if the reaction temperature increases, the slope of the initial part moves to that in the absence of solvent.These results are related to the formation of PVC gels or interactions. As the nature and percentage of substituted chlorine for a given chemical composition are the same in all the solvents and conditions studied, we propose that Cl-atoms of isotactic and/or heterotactic configurations are implied in the formation of PVC gels or interactions.     

Practical capillary gas chromatography—a systematic approach

Capillary gc is now rapidly expanding. Naturally, initiation is most often attempted on the basis of the experience acquired with packed columns. However, such an extrapolation is successful only if a number of essential peculiarities of capillary gc are considered. Based on practical examples this paper discusses six essential details: 1) design and maintenance of the gas flow paths, 2) the greatly increased importance of sampling technique, which should not be confined just to stream splitting, 3) the problems in quantitative analysis arising from small sample size, 4) specific sources of trouble related to small amounts of liquid phase, 5) specific arguments for the choice of the carrier gas, clearly pointing to hydrogen as the ideal carrier and, 6) the different way to approach column production. Figures for all selected examples are given.     

非晶态Co-B的局域电子结构的Xα原子簇计算

In the research on metallic glass, there are arguments against the "rigid band charge transfer", model which assumes a charge transfer from metalloid atoms to transition metal atoms to explain the experimental evidence of linear reduction of average atomic magnetic moment with the increasing concentration of metalloid atoms, but they could not explain the experimental relation of the reduction. In the present work, spin-polarized SCC-DV-X_a calculation for atomic clusters for metallic glass Co-B has been empoloyed to investigate the local electronic structure and magnetic property of the metallic glass. As opposed to the "rigid band charge transfer" model, calculation in the present work indicates that charge transfers from Co4s to both B and Co3d. It is found that there is Co3d4s-B2p hybird bonding in Co-B, which leads to the linear reduction of average atomic magnetic moment. Thus the explanation removes the above controversy.     

Faster GC analyses performed by flow programming in short capillary columns

The technique of programming the carrier gas flow rate in gas chromatography, especially in connection with the use of capillary columns shorter than 10 m can significantly accelerate GC analyses. Equations for calculation of the parameters of the exponential flow function and retention data are described. The effects of flow programming in a short capillary column are shown in a few chromatograms. Different programming rates are tested and compared with temperature programming.     

Development of new glass composite membranes and their properties for low temperature H2/O2 fuel cells.

A new glass electrolyte formed by constant amounts of titanium oxide (TiO2) and various amount of phosphotungstic acid (PWA) doped P2O5-SiO2 is prepared using the sol-gel process. The structural formation is confirmed by Fourier infrared spectroscopy (FTIR) and from thermogravimetric and differential thermal analysis (TG/DTA) measurements, the glasses display good thermal stability. Further characterisation is undertaken by N2 adsorption/desorption measurements, proton conductivity and hydrogen permeability analyses and a H2/O2 fuel cell test is also performed. The glass materials with large pores and specific surface area are suitable for use as the electrolyte in H2/O2 fuel cells. The effect of TiO2 processing with constant amount of PWA in phosphosilicate glasses, is investigated and discussed. The hydrogen permeability is 1.57x10(-11) mol cm(-1) s(-1) Pa(-1) at 110 degrees C for 0.8 mm thick glass; a power density of 46.3 mW cm(-2) at 125 mA cm(-2) and a current density of 175 mA cm(-2) is obtained (T=28 degrees C, relative humidity).     

Thermal properties of fluoride glasses and their gel precursors

Xerogels were prepared from zirconium, barium, aluminum, lanthanum and lithium acetates, corresponding to a Li containing ZBLA composition. The study of their thermal properties (DSC, TG/DTG, FT-IR) showed that they might be used as chemically stable precursors in the preparation of fluoride glasses. Hydrofluoric acid in solution was chosen as a mild fluorinating agent. This newly proposed technique of fluorinating allowed to obtain high quality ZBLALi glass which presents the advantage of higher thermal stability and homogeneity in comparison with the glass obtained using individual commercial fluorides.This revised version was published online in November 2005 with corrections to the Cover Date.     

Practical limitations of capillary gas chromatography

Glass capillary gas chromatography is a high resolution separation method which allows the qualitative and quantitative analysis of even complex mixtures, which may contain many components–also isomeric–in a wide range of volatilities, polarities and concentrations. The principal limitation of gas chromatographic application is given by an insufficient volatility of the species to be separated. Elevated temperatures have to be applied if the application range is to be extended and to achieve steep peak profiles, i.e. low detection limits at high resolution. The use of elevated temperatures is limited, of course, by the temperature stability of both the solvent (stationary liquid and support) and the solutes. The problems of trace analysis for low volatility compounds at high resolution and its limitational parameters regarding sampling, separation and detection are discussed. The applicability of glass capillary columns in this field is influenced by the following parameters: tailing behaviour; irreversible adsorption of polar and decomposition of unstable solutes; thermal stability of stationary liquid (including the support deactivation); separation efficiency and sample capacity (film thickness). Multidimensional gas chromatography using capillary columns coupled either with a packed or another capilllary column for preseparations may be applied with advantage in the analysis of complex mixtures.