Ammonium chloride salting out extraction/cleanup for trace-level quantitative analysis in food and biological matrices by flow injection tandem mass spectrometry

A sample extraction and purification procedure that uses ammonium-salt-induced acetonitrile/water phase separation was developed and demonstrated to be compatible with the recently reported method for pesticide residue analysis based on fast extraction and dilution flow injection mass spectrometry (FED-FI-MS). The ammonium salts evaluated were chloride, acetate, formate, carbonate, and sulfate. A mixture of NaCl and MgSO₄, salts used in the well-known QuEChERS method, was also tested for comparison. With thermal decomposition/evaporation temperature of <350 °C, ammonium salts resulted in negligible ion source residual under typical electrospray conditions, leading to consistent method performance and less instrument cleaning. Although all ammonium salts tested induced acetonitrile/water phase separation, NH₄Cl yielded the best performance, thus it was the preferred salting out agent. The NH₄Cl salting out method was successfully coupled with FI/MS/MS and tested for fourteen pesticide active ingredients: chlorantraniliprole, cyantraniliprole, chlorimuron ethyl, oxamyl, methomyl, sulfometuron methyl, chlorsulfuron, triflusulfuron methyl, azimsulfuron, flupyrsulfuron methyl, aminocyclopyrachlor, aminocyclopyrachlor methyl, diuron and hexazinone. A validation study was conducted with nine complex matrices: sorghum, rice, grapefruit, canola, milk, eggs, beef, urine and blood plasma. The method is applicable to all analytes, except aminocyclopyrachlor. The method was deemed appropriate for quantitative analysis in 114 out of 126 analyte/matrix cases tested (applicability rate = 0.90). The NH₄Cl salting out extraction/cleanup allowed expansion of FI/MS/MS for analysis in food of plant and animal origin, and body fluids with increased ruggedness and sensitivity, while maintaining high-throughput (run time = 30 s/sample). Limits of quantitation (LOQs) of 0.01 mg kg⁻¹ (ppm), the ‘well-accepted standard’ in pesticide residue analysis, were achieved in >80% of cases tested; while limits of detection (LODs) were typically in the range of 0.001–0.01 mg kg⁻¹ (ppm). A comparison to a well-established HPLC/MS/MS method was also conducted, yielding comparable results, thus confirming the suitability of NH₄Cl salting out FI/MS/MS for pesticide residue analysis.     

Flow injection analysis simulations and diffusion coefficient determination by stochastic and deterministic optimization methods

Stochastic and deterministic simulations of dispersion in cylindrical channels on the Poiseuille flow have been presented. The random walk (stochastic) and the uniform dispersion (deterministic) models have been used for computations of flow injection analysis responses. These methods coupled with the genetic algorithm and the Levenberg–Marquardt optimization methods, respectively, have been applied for determination of diffusion coefficients. The diffusion coefficients of fluorescein sodium, potassium hexacyanoferrate and potassium dichromate have been determined by means of the presented methods and FIA responses that are available in literature. The best-fit results agree with each other and with experimental data thus validating both presented approaches.     

Determination of Total Chromium in Biological Samples by Automated Reagent Injection Chemiluminescence Analysis

A sensitive method for the determination of total chromium in real samples by flow injection–chemiluminescence (FI–CL) analysis was proposed. It was found that the CL intensity from luminol–lysozyme reaction could be markedly quenched, and the decrease of CL intensity was linear with the logarithm of Cr(III) concentrations over the range of 5.0 to 4000 pg mL^?1 with a detection limit of 2.0 pg mL^?1 (3σ) and relative standard deviations (RSDs) of 3.0, 2.6, and 2.0% for 10, 100, and 1000 pg mL^?1 Cr(III) (n = 7), respectively. At a flow rate of 2.0 mL min^?1, the whole process including sampling and washing could be accomplished within 36 s. The proposed CL method was successfully applied to the determination of total chromium in pharmaceutical capsules, a dietary supplement, and spiked human serum samples, with recoveries from 92.2 to 108.4% and RSDs of less than 4.0%. Using the homemade FI–CL model, the binding constant (K = 4.38 × 10⁶ L mol^?1) and the binding sites (n ≈ 1) of Cr(III) to lysozyme were given.     

Diffusion of magnetic nanoparticles in a multi-site injection process within a biological tissue during magnetic fluid hyperthermia using lattice Boltzmann method

In this study the lattice Boltzmann model (LBM) has been used to simulate diffusion of magnetic nanoparticles (MNPs) injected at multiple sites inside a biological tissue during magnetic fluid hyperthermia (MFH). To validate the numerical results, diffusion in infinite one and two dimensional domains have been compared with the analytical solutions. Agreement were excellent. Also diffusion of a water based nanofluid containing magnetite MNPs (ferrofluid) for mono and multi-site injection in the tissue has been studied. Moreover, the effects of ferrofluid injection volume as well as infusion flow rate of ferrofluid on the distribution of MNPs have been investigated.     

An experimental study of fuel injection strategies in CAI gasoline engine

Combustion of gasoline in a direct injection controlled auto-ignition (CAI) single-cylinder research engine was studied. CAI operation was achieved with the use of the negative valve overlap (NVO) technique and internal exhaust gas re-circulation (EGR). Experiments were performed at single injection and split injection, where some amount of fuel was injected close to top dead centre (TDC) during NVO interval, and the second injection was applied with variable timing. Additionally, combustion at variable fuel-rail pressure was examined.Investigation showed that at fuel injection into recompressed exhaust fuel reforming took place. This process was identified via an analysis of the exhaust-fuel mixture composition after NVO interval. It was found that at single fuel injection in NVO phase, its advance determined the heat release rate and auto-ignition timing, and had a strong influence on NO_X emission. However, a delay of single injection to intake stroke resulted in deterioration of cycle-to-cycle variability. Application of split injection showed benefits of this strategy versus single injection. Examinations of different fuel mass split ratios and variable second injection timing resulted in further optimisation of mixture formation. At equal share of the fuel mass injected in the first injection during NVO and in the second injection at the beginning of compression, the lowest emission level and cyclic variability improvement were observed.     

(Ti,Al,Si,C)N nanocomposite coatings synthesized by plasma-enhanced magnetron sputtering

Materials’ surface service property could be enhanced by transition metal nitride hard coatings due to their high hardness, wear and high temperature oxidation resistance, but the higher friction coefficient (0.4-0.9) of which aroused terrible abrasion. In this work, quinternary (Ti,Al,Si,C)N hard coating 3-4 μm was synthesized at 300 °C using plasma enhanced magnetron sputtering system. It was found that the coating's columnar crystals structure was restrained obviously with the increase of C content and a non-columnar crystals growth mode was indicated at the C content of 33.5 at.%. Both the XRD and TEM showed that the (Ti,Al,Si,C)N hard coatings had unique nanocomposite structures composed of nanocrystalline and amorphous nc-(Ti,Al)(C,N)/nc-AlN/a-Si₃N₄/a-Si/a-C. However, the coatings were still super hard with the highest hardness of 41 GPa in spite of the carbon incorporation. That a-C could facilitate the graphitization process during the friction process which could improve the coating's tribological performance. Therefore, that nanocomposite (Ti,Al,Si,C)N coatings with higher hardness (>36 GPa) and a lower friction coefficient (<0.2) could be synthesized and enhance the tribological performance and surface properties profoundly.     

Coating of Cr-V ledeburitic steel with CrN containing a small addition of Ag

Samples made from Vanadis 6 PM ledeburitic tool steel were surface machined, ground, and mirror polished. They were heat treated and coated with CrN with and without Ag addition by reactive magnetron sputtering. The CrN film grew in a typically columnar manner. A small addition of 3% Ag did not lead to alterations in the growth mechanism. The hardness of the CrN coating was 16.79 ± 1.49 GPa compared to 15.97 ± 1.44 GPa for the coating with Ag addition. The Ag addition in the CrN improved adhesion of the coating, which can be attributed to the capability of CrAgN coating to accommodate higher deformation energy before failure. The CrAgN coating exhibited superior tribological properties at intermediate temperatures. Compared to pure CrN the friction coefficient is lowered to 70-75% when measured at 400 and 500 °C, respectively. This is reflected in a reduction in the volume wear, which was found to be three times lower for the coating containing Ag. Flexural strength decreased slightly for the CrN- or CrAgN-coated material compared to uncoated steel. However, as the decrease in flexural strength is very weak there is practically no risk of significant embrittlement of the investigated material due to the CrN coating with or without Ag addition.     

Characterization of coating probe with Ti-DLC for electrical scanning probe microscope

In electrical scanning probe microscope (ESPM) applications, the wear and conductivity of the probe are undoubtedly serious concerns since they affect the integrity of the measurements. This study investigates the characterization of Ti doped diamond-like-carbon (DLC) as coating material on a silicon cantilever for ESPM. We deposited a layer of Ti-DLC thin film on the surface of Si cantilever by magnetron sputtering. The morphology and composition of the Ti-DLC films were characterized by scanning electron microscopy and Raman spectroscopy, respectively. We also compared the wear resistance, electric conductivity and scanning image quality of the Ti-DLC-coated probes with those of commercially available conductive probes. The results showed that the electric conductivity and the scanning image quality of the Ti-DLC-coated probes were the same as the commercial conductive probes, while the wear resistance and service life was significantly better.     

一种考虑IGBT基区载流子注入条件的物理模型

提出了一种考虑绝缘栅极双极晶体管(insulated gate bipolar transistor,IGBT) 基区载流子不同注入条件的物理模型. 在小注入和大注入情况下,分别建立描述IGBT基区载流子运动的输运方程(ambipolar transport equation,ATE),并确定边界条件. 采用傅里叶级数法求解载流子输运方程,并将计算结果分别与IGBT手册提供的实验数据和Hefner模型计算结果相比较,验证了本文提出物理模型的正确性. 关键词： 绝缘栅极双极晶体管 物理模型 注入条件 双极输运方程     

Split injection: A simple introduction of subnanoliter sample volumes for chip electrophoresis

The ability to accurately inject small volumes of sample into microfluidic channels is of great importance in electrophoretic separations. While electrokinetic injection of nanoliter scale volumes is commonly utilized in microchip capillary electrophoresis (MCE), mobility and matrix bias makes quantitation difficult. Herein, we describe a new injection method based on the simple patterning of the crossing of channels that does not require sophisticated instrumentation. The sample volume injected into the separation channel is dependent on the ratio of the widths of the crossing channels. This injection method is capable of introducing, into a separation channel, multiple plugs of sample on a large scale. This injection technique is tested for zone electrophoresis in native and surface modified poly(dimethylsiloxane) (PDMS) chips.