BNCT蒙特卡洛剂量计算的混合网格算法研究

在硼中子俘获治疗(BNCT)的蒙特卡洛(MC)剂量计算中,通常使用单一的网格模式,如16mm,8mm,4mm.使用细网格计算资源太大,使用粗网格,计算精度不够,为此,根据粒子穿透深度和计数量的变化梯度,采用混合网格模拟计算,达到了细网格的精度,时间仅为细网格的37%.     

Thermal decomposition of transition metal carboxylates

Dynamics of changes in microstresses during thermal decomposition of Cu(HCOO)₂ crystals and their effect on the thermal decomposition kinetics were studied by IR spectroscopy at 105 to 120 °C. The formation of solid intermediate HCOOCu was observed, and the dynamics of its accumulation was followed. Kinetic regularities of transformation of HCOO groups were compared with those for gas evolution.For Communication 1, see Ref. 1.Translated from Izvestiya va Akademii Nauk. Seriya Khimicheskaya, No. 2, pp. 350–354, February, 1996.     

Dimensionally and thermally stable polymer,containing disordered graphitic structure and adamantane

In an attempt to develop a low‐k interlayer dielectric, adamantane‐diphenyldiethynyl moiety containing oligomer is prepared. Oligomerization of 1,3,5,7‐tetrakis[3/4‐ethynylphenyl]adamantane ( 4 ) is accomplished by a Glaser–Hay oxidative coupling with 1,3,5‐triethynylbenzene and phenylacetylene end‐capping agent. The CHCl₃ soluble oligomer is then thermally treated by step‐curing at 200, 300, 380, and 450 °C for 30 min at each temperature under nitrogen flow to render a shiny void‐free black polymer. TGA analysis indicates that the polymer is stable under nitrogen up to 500 °C with a marginal decomposition up to 800 °C. Solid‐state ¹³C NMR, Raman scattering, and FTIR are used to characterize the structure of the polymer. The polymer consists of amorphous carbon networks with the adamantane moieties and nanosized graphitic regions (clusters), which are generated from the thermal crosslinking of the diphenyldiethynyl units. It shows a remarkably low linear coefficient of thermal expansion (～25 ppm/°C), presumably due to the presence of the disordered graphitic structure. Its high density (～1.21 g/cm³), refractive index (～1.80 at 632 nm), and Young's modulus (～17.0 GPa) are also consistent with the interpretation. This study reveals important details about the effect of microscopic structure on the macroscopic properties of the highly crosslinked polymer. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6909–6925, 2006     

InAs/GaSb superlattice focal plane arrays for high-resolution thermal imaging

The first fully operational mid-IR (3–5 μm) 256×256 IR-FPA camera system based on a type-II InAs/GaSb short-period superlattice showing an excellent noise equivalent temperature difference below 10 mK and a very uniform performance has been realized. We report on the development and fabrication of the detecor chip, i.e., epitaxy, processing technology and electro-optical characterization of fully integrated InAs/GaSb superlattice focal plane arrays. While the superlattice design employed for the first demonstrator camera yielded a quantum efficiency around 30%, a superlattice structure grown with a thicker active layer and an optimized V/III BEP ratio during growth of the InAs layers exhibits a significant increase in quantum efficiency. Quantitative responsivity measurements reveal a quantum efficiency of about 60% for InAs/GaSb superlattice focal plane arrays after implementing this design improvement. The paper presented there appears in Infrared Photoelectronics, edited by Antoni Rogalski, Eustace L. Dereniak, Fiodor F. Sizov, Proc. SPIE Vol. 5957, 595707 (2005).     

Crosslinked epoxy materials exhibiting thermal remendablility and removability from multifunctional maleimide and furan compounds

Crosslinked polymeric materials, which exhibit thermal remendability and removability through Diels–Alder (DA) and retro‐DA reactions, were obtained from using multifunctional maleimide and furan compounds as monomers. The synthesized monomers possess low melting points and good solubility in organo solvents to show excellent processing properties. The performance of DA and retro‐DA reactions were demonstrated with DSC and FTIR measurements. High performance of thermal remendablility and removability of the crosslinked materials were observed with SEM and solvent tests. These materials were applicable in advanced encapsulants and structural materials. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 905–913, 2006     

Stereocontrol of diene polymers by topochemical polymerization of substituted benzyl muconates and their crystallization properties

We report the stereocontrol of diene polymers by the topochemical polymerization of alkoxy-substituted benzyl muconates in the solid state. A monomer stacking structure is controlled by the weak intermolecular interactions in the monomer crystals, depending on the structure and position of the alkoxy-substituent. The translational and alternating types of molecular stacking structures in a column provide diisotactic and disyndiotactic polymers, respectively, by the solid-state polymerization under UV and γ-ray irradiation. On the other hand, the meso and racemo structures of the resulting polymers are determined by the molecular symmetry of the used muconate monomers. The various substituted benzyl ester polymers are transformed into the same ethyl ester polymers with the four types of tacticities. The structure and crystallization behavior of the substituted benzyl ester polymers as well as the ethyl ester polymers have been revealed in detail. We clarify the effects of the tacticity on the crystallization property of the stereoregular polymuconates. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4952–4965, 2006     

Highly soluble and optically transparent poly (ether imide)s based on 2,6‐ or 2,7‐bis(3,4‐dicarboxyphenoxy)naphthalene dianhydride and aromatic bis(ether amine)s bearing trifluoromethyl groups

Two series of novel fluorinated poly(ether imide)s (coded IIIA and IIIB ) were prepared from 2,6‐bis(3,4‐dicarboxyphenoxy)naphthalene dianhydride and 2,7‐bis(3,4‐dicarboxyphenoxy)naphthalene dianhydride, respectively, with various trifluoromethyl‐substituted aromatic bis(ether amine)s by a standard two‐step process with thermal or chemical imidization of the poly(amic acid) precursors. These fluorinated poly(ether imide)s showed good solubility in many organic solvents and could be solution‐cast into transparent, flexible, and tough films. These films were nearly colorless, with an ultraviolet–visible absorption edge of 364–386 nm. They also showed good thermal stability with glass‐transition temperatures of 221–298 °C, 10% weight loss temperatures in excess of 489 °C, and char yields at 800 °C in nitrogen greater than 50%. The 2,7‐substituted IIIB series also showed better solubility and higher transparency than the isomeric 2,6‐substituted IIIA series. In comparison with nonfluorinated poly (ether imide)s, the fluorinated IIIA and IIIB series showed better solubility, higher transparency, and lower dielectric constants and water absorption. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5909–5922, 2006     

Synthesis and liquid crystalline properties of new amide‐modified poly(1,4‐cyclohexanedimethylene terephthalate)

New series of cycloaliphatic poly(ester‐amide)s, poly(1,4‐cyclohexanedimethyleneterephthalate‐co‐1,3‐cyclohexanedimethylene terephthalamide), were synthesized through solution polymerization route. The compositions of ester/amide units in the copolymers were varied from 0 to 100% by varying the amount of 1,4‐cyclohexanedimethanol and 1,3‐cyclohexanebis(methylamine) in the feed. The structures of the polymers were confirmed by NMR and FTIR, and the molecular weights were determined by inherent viscosity. The composition analysis by NMR reveals that the reactivity of the diamine toward the acid chlorides is lowered than that of diol, which results in the formation of more ester content in the poly (ester‐amides). The thermal analysis indicate that the new poly(ester‐amide)s having less than 10 mol % of amide linkages are thermotropic liquid crystalline from 200 to 250 °C and a thread like nematic phases are observed under the polarizing microscope. WXRD studies suggest that the liquid crystalline domains promote the nucleation process in the polyester chains and increases the percent crystallinity of the poly(ester‐amide)s. The glass transition temperature of the copolymers initially increases with increase in amide units because of the presence of nematic phases and subsequently follows the Flory–Fox behavior. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 42–52, 2006     

Thermal stability of shear-induced precursor structures in isotactic polypropylene by rheo-X-ray techniques with couette flow geometry

Combined in situ rheo-SAXS (small-angle X-ray scattering) and -WAXD (wide-angle X-ray diffraction) studies using couette flow geometry were carried out to probe thermal stabilty of shear-induced oriented precursor structure in isotactic polypropylene (iPP) at around its normal melting point (162 °C). Although SAXS results corroborated the emerging consensus about the formation of “long-living” metastable mesomorphic precursor structures in sheared iPP melts, these are the first quantitative measures of the limiting temperature at which no oriented structures survive. At the applied shear, rate = 60 s⁻¹ and duration t_s = 5 s, the oriented iPP structures survived a temperature of 185 °C for 1 h after shear, while no stable structures were detected at and above 195 °C. Following Keller's concepts of chain orientation in flow, it is proposed that the chains with highly oriented high molecular weight fraction are primarily responsible for their stability at high temperatures. Furthermore, the effects of flow condition, specifically the shear temperature, on the distributions of oriented and unoriented crystals were determined from rheo-WAXD results. As expected, at a constant flow intensity (i.e., rate = 30 s⁻¹ and duration, t_s = 5 s), the oriented crystal fraction decreased with the increase in temperature above 155 °C, below which the oriented fraction decreased with the decrease in temperature. As a result, a crystallinty “phase” diagram, i.e., temperature versus crystal fraction ratio, exhibited a peculiar “hourglass” shape, similar to that found in many two-phase polymer–polymer blends. This can be explained by the competition between the oriented and unoriented crystals in the available crystallizable species. Below the shear temperature (155 °C), the unoriented crystals crystallized so rapidly that they overwhelmed the crystallization of the oriented crystals, thus depleting a major portion of the crystallizable species and increasing their contribution in the final total crystalline phase. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3553–3570, 2006     

Synthesis and characterization of polyimides derived from (3‐amino‐2,4,6‐trimethylphenyl)‐(3′‐aminophenyl)methanone and aromatic dianhydrides

A series of new polyimides were prepared via the polycondensation of (3‐amino‐2,4,6‐trimethylphenyl)‐(3′‐aminophenyl)methanone and aromatic dianhydrides, that is, 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA), 4,4′‐oxydiphthalic anhydride, 3,3′,4,4′‐benzophenone tetracarboxylic dianhydride, and 2,2′‐bis(3,4‐dicarboxyphenyl) hexafluoropropane dianhydride. The structures of the polyimides were characterized by Fourier transform infrared and NMR measurements. The properties were evaluated by solubility tests, ultraviolet–visible analysis, differential scanning calorimetry, and thermogravimetric analysis. The two different meta‐position‐located amino groups with respect to the carbonyl bridge in the diamine monomer provided it with an unsymmetrical structure. This led to a restriction on the close packing of the resulting polymer chains and reduced interchain interactions, which contributed to the solubility increase. All the polyimides except that derived from BPDA had good solubility in strong aprotic solvents, such as N‐methyl‐2‐pyrrolidinone, N,N′‐dimethylacetamide, N,N‐dimethylformamide, and dimethyl sulfone, and in common organic solvents, such as cyclohexanone and chloroform. In addition, these polyimides exhibited high glass‐transition values and excellent thermal properties, with an initial thermal decomposition temperature above 470 °C and glass‐transition temperatures in the range of 280–320 °C. The polyimide films also exhibited good transparency in the visible‐light region, with transmittance higher than 80% at 450 nm and a cutoff wavelength lower than 370 nm. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1291–1298, 2006