Adsorptive Stripping Voltammetric Determination of Ultra Trace of Zinc and Lead with Carbidopa as Complexing Agent in Food and Water Samples

In the present work, the cathodic stripping voltammetric methodology using a hanging mercury drop electrode was described for simultaneous determination of lead and zinc in different real samples. The method is based on adsorption of metal ions on mercury electrode using carbidopa as a suitable complexing agent. The potential was scanned to the negative direction and the differential pulse stripping voltammograms were recorded. Optimal conditions were found to be: accumulation time; 70 s, accumulation potential; 50 mV versus Ag/AgCl, scan rate; 40 mV s^?1, supporting electrolyte; 0.01 M ammonia buffer at pH 8.5, and concentration of carbidopa; 8.0 μM. The relationship between the peak current versus concentration was linear over the range of 0.1–210 and 0.2–170 nM for lead and zinc, respectively. The detection limits are 0.09 and 0.15 nM for lead and zinc ions respectively. The relative standard deviations at a concentration level of 70 nM of both metal ions are found 1.08 and 1.24% for lead and zinc ions respectively.     

Preconcentration of lead,cadmium, copper and zinc in water at the pg g−1 level by non-boiling evaporation

An evaluation of the non-boiling evaporation technique for the preconcentration of Pb, Cd, Cu, Zn at the pg g^?1 level in water samples is presented. Various improvements were made to allow efficient control of contamination problems at these extremely low concentrations. They include the choice of FEP Teflon for the evaporation containers and the use of sophisticated cleaning, ageing and pre-conditionning procedures. Detailed calibration graphs were obtained down to the sub-pg g^?1 level by processing ultra-low concentration standards. This technique was then applied to the determination of these four metals in snow samples collected in Greenland and Antarctica.     

Determination of lead in water samples by graphite furnace atomic absorption spectrometry after cloud point extraction

Cloud point extraction (CPE) has been used for the pre-concentration of lead, after the formation of a complex with 2-(5-bromo-2-pyridylazo)-5-(diethylamino)-phenol (5-Br-PADAP), and later analysis by graphite furnace atomic absorption spectrometry (GFAAS) using octylphenoxypolyethoxyethanol (TritonX-114) as surfactant. The chemical variables affecting the separation phase were optimized. Separation of the two phases was accomplished by centrifugation for 15 min at 4000 rpm. Under the optimum conditions i.e., pH 8.0, cloud point temperature 40 °C, [5-Br-PADAP] = 2.5 × 10⁻⁵ mol l⁻¹, [Triton X-114] = 0.05%, added methanol volume = 0.15 ml, pre-concentration of only 10 ml sample permitted an enhancement factor of 50-fold. The lower limit of detection (LOD) obtained under the optimal conditions was 0.08 μg l⁻¹. The precision for 10 replicate determinations at 5 μg l⁻¹ Pb was 2.8% relative standard deviation (R.S.D.). The calibration graph using the pre-concentration system for lead was linear with a correlation coefficient of 0.9984 at levels near the detection limits up to at least 30 μg l⁻¹. The method was successfully applied to the determination of lead in water samples.     

职业性铅接触对血压影响的研究

对１１８名铅接触工人及１０８名对照组工人的血压研究发现，在血铅为４４．２６μｇ／ｄＬ时，铅接触工人的收缩压显著高于对照组，分组研究发现，收缩压在级组剂量－反应关系趋势，在血铅３０．２０μｇ／ｄＬ，收缩压显著高于对照组，多元逐步回归分析发现，在控制一些其他影响血压的因素后，铅接触工人的血铅水平与收缩压和舒张压均有剂量－反应关系。     

微波增压溶样-石墨炉原子吸收光谱法同时测定植物性样品中微量铅镉

使用微波增压溶样法，将样品用HNO3—HClO4溶解后，用石墨炉原子吸收光谱法同时测定植物性样品中铅和镉。以磷酸二氢铵—硝酸镁作为基体改进剂，可使灰化温度大大提高，克服了基体的干扰。铅和镉的回收率分别为95．3％—104．8％和96．2％—105．5％，RSD分别为4．8％-7．2％和4．3％-7．6％。     

Solid-phase extraction system for Pb (II) ions enrichment based on multiwall carbon nanotubes coupled on-line to flame atomic absorption spectrometry

The present paper proposes the application of multiwall carbon nanotubes (MWCNTs) as a solid sorbent for lead preconcentration using a flow system coupled to flame atomic absorption spectrometry. The method comprises the preconcentration of Pb (II) ions at a buffered solution (pH 4.7) onto 30 mg of MWCNTs previously oxidized with concentrated HNO₃. The elution step is carried out with 1.0 mol L⁻¹ HNO₃. The effect of the experimental parameters, including sample pH, sampling flow rate, buffer and eluent concentrations were investigated by means of a 2⁴ full factorial design, while for the final optimization a Doehlert design was employed. Under the best experimental conditions the preconcentration system provided detection and quantification limits of 2.6 and 8.6 μg L⁻¹, respectively. A wide linear range varying from 8.6 up to 775 μg L⁻¹ (r > 0.999) and the respective precision (relative standard deviation) of 7.7 and 1.4% for the 15 and 200 μg L⁻¹ levels were obtained. The characteristics obtained for the performance of the flow preconcentration system were a preconcentration factor of 44.2, preconcentration efficiency of 11 min⁻¹, consumptive index of 0.45 mL and sampling frequency estimated as 14 h⁻¹. Preconcentration studies of Pb (II) ions in the presence of the majority foreign ions tested did not show interference, attesting the good performance of MWCNTs. The accuracy of the method was assessed from analysis of water samples (tap, mineral, physiological serum and synthetic seawater) and common medicinal herbs submitted to the acid decomposition (garlic and Ginkgo Biloba). The satisfactory recovery values obtained without using analyte addition method confirms the feasibility of this method for Pb (II) ions determination in different type of samples.     

Characteristics of subtractive anodic stripping voltammetry of Pb and Cd at silver and gold electrodes

Silver and gold electrodes are useful for the quantitative determination of lead and cadmium with subtractive anodic stripping voltammetry (SASV). The use of SASV is essential for achieving good separation between the two peaks, to eliminate the interference of nitrates when cadmium is present and to allow analysis at very low concentrations without the removal of oxygen. The deposition and dissolution of Pb²⁺ and Cd²⁺ proceed at underpotential (UPD) on both electrodes. The UPD properties of the deposits are the main factor determining the analytical characteristics of the ASV method and are strongly affected by the type and concentration of the electrolyte. The effects of anions (Cl⁻, Br⁻, SO₄²⁻, NO₃⁻) and acids (HNO₃, HClO₄, H₂SO₄, HCl) are shown. The two electrodes complement each other and, in addition, enable the qualitative identification of Pb²⁺ and Cd²⁺, since the peaks appear in opposite order on the two electrodes. Analysis of mixtures of the two analytes is restricted on gold but not on silver. At gold the two peaks overlap: (i) at concentrations of cadmium higher than 250 nM at deposition times greater than 30 s, (ii) in the presence of copper at concentrations higher than 1 μM, and (iii) in the presence of Triton X-100 at concentrations above 10 mg/l. The repeatability at 10 nM analyte is better than 2.5%. The detection limits for Pb²⁺ and Cd²⁺ at 120 s deposition time and 3500 rpm rotation rate are: dl_Pb/Ag=0.04 nM; dl_Cd/Ag=0.7 nM; dl_Pb/Au=0.1 nM; dl_Cd/Au=0.3 nM. The analysis of lead and cadmium in natural waters has been performed.     

Lead tetraacetate-iodine oxidation of 23-spirostanols

Reactions of 23R- and 23S-23-spirostanols in the 25R and 25S series with lead tetraacetate-iodine were studied. The reactions carried out at low temperature afforded d-seco-iododialdehydes and C₂₂ lactones, while similar reactions performed in refluxing tetrachloromethane yielded 20-chlorolactones and their 21-acetoxy derivatives irrespective of the hydroxyl group configuration at C-23. The reaction mechanisms are discussed.     

Slurry sampling for determination of lead in marine plankton by electrothermal atomic absorption spectrometry

A slurry sampling method has been developed for the determination of Pb in marine plankton by ETAAS using a freshwater plankton certified reference material (CRM 414). Slurries were prepared in 1–3% m/v range with 1% v/v HNO₃ by ultrasonic agitation for 5 min. The effects of several chemical modifiers, including Ir(NO₃)₂, Mg(NO₃)₂, Pd(NO₃)₂, Pd(NO₃)₂ + Mg(NO₃)₂, and Mg(NO₃)₂ + NH₄H₂PO₄, were investigated for the stabilization of Pb during thermal pretreatment. Lead in slurries was effectively stabilized up to 1000 °C with Ir, Pd and Pd + Mg modifiers among which Pd + Mg provided the best results with complete atomization at 1850 °C. Firings in the presence of Ir were, problematic due to ash formation inside the atomizer. Water, dilute HNO₃ and HF were examined as suspension medium. Dilute HNO₃ (1–2% v/v) proved to be advantageous over water as it afforded extraction of Pb from plankton almost quantitatively in 5 min agitation. Hydrofluoric acid was the least suitable medium. Increasing HF concentration up to 5% v/v resulted in inaccuracy and substantial background absorption. Fast-heating furnace method provided comparable accuracy and precision to that of conventional-heating in slurries of CRM 414. Detection limits and characteristic masses were, respectively, 0.49 μg L^− 1 and 32 pg for the conventional method and 0.62 μg L^− 1 and 37 pg for the fast-heating method. However, fast-heating approach suffered from distorted peaks at high temperatures and incomplete pyrolysis of matrix at lower temperatures. Analysis of marine plankton samples for Pb was performed by using the conventional furnace program. The results showed a high correlation with those obtained by solution ICP-MS. Differences were statistically insignificant within 95% confidence interval.     

Coupling continuous ultrasound-assisted extraction, preconcentration and flame atomic absorption spectrometric detection for the determination of cadmium and lead in mussel samples

Continuous ultrasound-assisted extraction has been coupled with preconcentration and flame atomic absorption spectrometry for the determination of cadmium and lead in mussel samples. Experimental designs were used for the optimisation of the leaching and preconcentration steps. The use of diluted nitric acid as extractant in the continuous mode at a flow rate of 3.5 ml min⁻¹ and room temperature was sufficient for quantitative extraction of these trace metals. A minicolumn containing a chelating resin (Chelite P, with aminomethylphosphoric acid groups) was proved as an excellent material for the quantitative preconcentration of cadmium and lead prior to their flame atomic absorption detection. A flow injection manifold was used as interface for coupling the three analytical steps, which allowed the automation of the whole analytical process. A good precision of the whole procedure (2.0 and 2.3%), high enrichment factors (20.5 and 11.8) and a detection limit of 0.011 and 0.25 μg g⁻¹ for cadmium and lead, respectively, were obtained for 80 mg of sample. The sample throughputs were ca. 16 and 14 samples h⁻¹ for cadmium and lead, respectively. The accuracy of the analytical procedures was verified by using a standard reference material (BCR 278-R, mussel tissue) and the results were in good agreement with the certified values. The method was successfully applied to the determination of trace amounts of cadmium and lead in mussel samples from the coast of Galicia (NW, Spain).