矩底拱面状微透镜阵列的氩离子束刻蚀

在ＺｒＯ２、ＩｎＰ、Ｓｉ及ＳｉＯ２即融凝石英衬底上用氩离子束刻蚀制作面阵矩底拱面状微透镜阵列，给出了氩离子束在不同的入射角度下刻蚀器件的速率与离子束能量之间的关系。实验表明，用国产ＢＰ２１２紫外正型光刻胶制作的光致抗蚀剂掩膜图形在经过优化的工艺条件下可以通过氩离子束刻蚀将预定图形转移到衬底材料中。     

Effect of high gamma dose on the PADC properties

The effect of the properties of PADC nuclear track detectors after exposure to high doses of gamma absorbed doses up to 5×10⁵ Gray (50 Mrad) were studied. The gamma source was a 9.03 PBq (244 KCi), Co-60 source. Results indicate that each of the bulk etch rate (V_b), the tracks etch rate (V_t) and the sensitivity (V) of the detectors increases with the high gamma absorbed dose, but there is a drop in these parameters at the low gamma absorbed dose. Signs of surface roughness were observed by increasing the gamma absorbed doses and changes in color observed for doses larger than 2×10⁵ Gray. The temperature of detectors during irradiation time reached 41°C. The fission fragment tracks (from Cf-252 source) disappeared quickly within the etching time (minutes) for total absorbed doses greater than 3×10⁵ Gray due to their high bulk etch rate.     

Angular response characteristic of pyramid shape fast neutron dosimeter using CR-39 films

CR-39 is a highly sensitive etched track detector for neutron monitoring and dosimetry applications but its dose equivalent response is strongly direction dependent with respect to the incident neutrons. This is considered to be a major drawback for their use. In the present study, an attempt has been made to develop a pyramid shaped dosimeter, which consists of polyethylene material of thickness 1 mm with the provision to hold three CR-39 films at an angle of 35° to each other. The response of CR-39 in this configuration under optimum electrochemical etching at elevated temperature have been found nearly angular independent and therefore the dosimeter can be used for neutron monitoring, i.e. personnel as well as area monitoring.     

高能量激光诱导铝等离子体的发射光谱研究

用钕玻璃激光器 (～ 2 5J)烧蚀铝靶获得等离子体 ,以氩气作为保护气体 ,分析了环境气压、等离子体的观测高度、工作电压、激光功率密度对谱线强度的影响 ,并进行了简短的讨论。实验结果表明 ,环境气压为 88kPa时谱线强度最大 ;相同气压下随着观测高度的增大 ,谱线强度明显减弱 ,在气压为 88kPa观测位置距样品表面 1 5～ 2mm时谱线强度较强 ;并且随着激光工作电压、功率密度的增大 ,谱线强度逐渐提高。     

Annealing effects on structure and laser-induced damage threshold of Ta2O5/SiO2 dielectric mirrors

The effects of annealing on structure and laser-induced damage threshold (LIDT) of Ta₂O₅/SiO₂ dielectric mirrors were investigated. Ta₂O₅/SiO₂ multilayer was prepared by ion beam sputtering (IBS), then annealed in air under the temperature from 100 to 400 °C. Microstructure of the samples was characterized by X-ray diffraction (XRD). Absorption of the multilayer was measured by surface thermal lensing (STL) technique. The laser-induced damage threshold was assessed using 1064 nm free pulsed laser at a pulse length of 220 μs.

It was found that the center wavelength shifted to long wavelength gradually as the annealing temperature increased, and kept its non-crystalline structure even after annealing. The absorbance of the reflectors decreased after annealing. A remarkable increase of the laser-induced damage threshold was found when the annealing temperature was above 250 °C.     

Nanotextured multicrystalline Al‐BSF solar cells reaching 18% conversion efficiency using industrially viable solar cell processes

We report recent achievements in adapting industrially used solar cell processes on nanotextured surfaces. Nanostructures were etched into c‐Si surfaces by dry exothermic plasma‐less reaction of F species with Si in atmospheric pressure conditions and then modified using a short post‐etching process. Nanotextured multicrystalline wafers are used to prepare Al‐BSF solar cells using industrially feasible solar cell proc‐ essing steps. In comparison to the reference acidic textured solar cells, the nanostructured cells showed gain in short circuit current (J_sc) of up to 0.8 mA/cm² and absolute gain in conversion efficiency of up to 0.3%. The best nanotextured solar cell was independently certified to reach the conversion efficiency of 18.0%. (© 2015 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

氧化锌掺铝绒面薄膜在有机光伏电池中的应用

目前有机光伏电池的吸光活性层电学传输特性和光学吸收特性的不匹配是制约其能量转换效率提升的主要原因之一. 通过陷光结构对入射光进行调控, 提高电池对光的约束和俘获能力从而达到“电学薄”和“光学厚”的等效作用, 是解 决有机光伏电池电学和光学不匹配的有效手段. 本文采用湿法刻蚀技术获得了系列时间梯度的绒面氧化锌掺铝薄膜, 并将其作为有机光伏电池的入射陷光电极, 显著增强了电池的光学吸收. 研究发现, 当使用浓度0.5%的稀HCL腐蚀30 s后的氧化锌掺铝薄膜作为入射电极后, 电池的光电性能和效率显著增强. 基于此绒面电极电池的电流密度比平面结构的电池提高了8.17%, 效率改善了11.29%. 通过对绒面电极表面的修饰处理, 实现了电极与光活性层之间良好的界面接触, 从而减小了对电池的开路电压和填充因子的影响.     

热拉伸和化学腐蚀相结合制备弯曲光纤探针

提出了原子力/光子扫描隧道显微镜(AF/PSTM)系统的关键部分——双功能弯曲光纤探针的制作方法.采用热拉伸与动态、静态两步化学腐蚀相结合的方法制作出AF/PSTM弯曲光纤探针，弯曲角度约为150°，尖端曲率半径优于100nm，锥角范围为60°—90°.将这种双功能弯曲光纤探针应用在新研制的AF/PSTM系统上，同时获得了样品的光学与形貌图像，实现了图像分解. 关键词： 原子力/光子扫描隧道显微镜 光纤探针 热拉伸 化学腐蚀     

Chemical etching investigation of polycrystalline p-type 6H-SiC in HF/Na2O2 solutions

In this work, an experimental study on the chemical etching reaction of polycrystalline p-type 6H-SiC was carried out in HF/Na₂O₂ solutions. The morphology of the etched surface was examined with varying Na₂O₂ concentration, etching time, agitation speed and temperature. The surfaces of the etched samples were analyzed using scanning electron microscopy (SEM), energy-dispersive X-ray (EDX) Fourier transform infrared spectroscopy (FT-IR) and photoluminescence. The surface morphology of samples etched in HF/Na₂O₂ is shown to depend on the solution composition and bath temperature. The investigation of the HF/Na₂O₂ solutions on 6H-SiC surface shows that as Na₂O₂ concentration increases, the etch rate increases to reach a maximum value at about 0.5 M and then decreases. A similar behaviour has been observed when temperature of the solution is increased. The maximum etch rate is found for 80 °C. In addition, a new polishing etching solution of 6H-SiC has been developed. This result is very interesting since to date no chemical polishing solution has been developed on the material.     

Shallow surface etching of organic and inorganic compounds by electrospray droplet impact

The electrospray droplet impact (EDI) was applied to bradykinin, polyethylene terephthalate (PET), SiO₂/Si, and indium phosphide (InP). It was found that bradykinin deposited on the stainless steel substrate was ionized/desorbed without the accumulation of radiation products. The film thickness desorbed by a single collisional event was found to be less than 10 monolayers. In the EDI mass spectra for PET, several fragment ions were observed but the XPS spectra did not change with prolonged cluster irradiation. The etching rate for SiO₂ by EDI was measured to be ∼0.2 nm/min. The surface roughness of InP etched by EDI was found to be one order of magnitude smaller than that etched by 3 keV Ar⁺ for about the same etching depths. EDI is capable of shallow surface etching with little damage left on the etched surface.