Microstructure and high-temperature wear resistance of a laser surface alloyed γ-TiAl with carbon

TiC reinforced composite coating on γ-TiAl alloy was successfully fabricated by laser surface alloying with carbon. The fine TiC reinforcing phase had a gradient distribution in the coating, and its growth morphology of TiC in laser surface alloyed coating was in unique faceted platelet-like. The composite coating exhibited high hardness and excellent high-temperature sliding wear resistance.     

Investigating laser rapid manufacturing for Inconel-625 components

This paper presents an investigation of laser rapid manufacturing (LRM) for Inconel-625 components. LRM is an upcoming rapid manufacturing technology, it is similar to laser cladding at process level with different end applications. In general, laser-cladding technique is used to deposit materials on the substrate either to improve the surface properties or to refurbish the worn out parts, while LRM is capable of near-net shaping the components by layer-by-layer deposition of the material directly from CAD model. In the present study, a high-power continuous wave (CW) CO₂ laser system, integrated with a co-axial powder-feeding system and a three-axis workstation were used. The effect of processing parameters during LRM of Inconel-625 was studied and the optimum set of parameters for the maximum deposition rate was established employing Orthogonal L9 array of Taguchi technique. Results indicated that the powder feed rate and the scan speed contributed about 56% and 26%, respectively to the deposition rate, while the influence of laser power was limited to 10% only. Fabricated components were subjected to non-destructive testing (like—ultrasonic testing, dye-penetrant testing), tensile testing, impact testing, metallographic examinations and micro-hardness measurement. The test results revealed defect-free material deposition with improved mechanical strength without sacrificing the ductility.     

A simple model for high fluence ultra-short pulsed laser metal ablation

The ultra-short laser metal ablation is a very complex process, the complete simulation of which requires applications of complicated hydrodynamics or molecular dynamics models, which, however, are often time-consuming and difficult to apply. For many practical applications, where the laser ablation depth is the main concern, a simplified model that is easy to apply but at the same time can also provide reasonably accurate predictions of ablation depth is very desirable. Such a model has been developed and presented in this paper, which has been found to be applicable for laser pulse duration up to 10 ps based on comparisons of model predictions with experimental measurements.     

Laser pulse heating of steel surface and flexural wave analysis

Laser gas-assisted material processing finds wide application in industry. The modelling of heating, elastic response of the substrate material, and the wave analysis gives insight into the laser workpiece interaction. In the present study, laser gas-assisted heating of steel is considered. The normal component of the thermal stress is taken as the source of load for the flexural wave generation in the material. The flexural wave generated is simulated and the wave characteristics are analyzed at four locations at the workpiece surface. The numerical scheme employing a control volume approach is introduced when solving the governing equations of flow and heat transfer while finite element and spectran element methods are used when solving the stress and wave equations. It is found that the normal component of the stress is tensile. The dispersion effect of the workpiece material, interference of the reflected beam, and partial overlapping of second mode of the travelling wave enable to identify a unique pattern in the travelling wave in the substrate.     

用激光散斑场检测药液内杂质含量分布

本文分析了利用散斑斑纹检测大输液药品杂质含量的机理，报道了检测大输液药品杂质的实例．     

Geometrically qualified ESPI vibration analysis of an engine

This paper presents an application in the automotive industry where a combination of electronic speckle-pattern interferometry and laser doppler velocimetry were used at a critical stage in the design process of an internal combustion engine. Combined deformation and surface relief measurements were used to study the phase and amplitude of deformation of a vibrating engine. The relief data was combined with the interferometer geometry and used to geometrically correct the deformation data, in an effort to improve accuracy. The measurements allowed rapid identification and quantification of design weaknesses, particularly those causing undesirable resonances. This led to a significant reduction in the design time and lowering of costs, when compared with existing design optimisation methods.     

激光磁共振用于对NO_2分子的定量测量

本文叙述了采用CO激光磁共振方法对NO_2分子作定量测量,给出了激光磁共振信号幅度的数学表达式以及信号与分子浓度、激光功率等实验参数之间的依赖关系,实验结果与理论分析一致。     

Deposition of Au/TiO2 film by pulsed laser

Au nanoparticles, which were photoreduced by a Nd:YAG laser in HAuCl₄ solution containing TiO₂ colloid and accompanied by the TiO₂ particles, were deposited on the substrate surface. The film consisting of Au/TiO₂ particles was characterized by the absorption spectra, scanning electron microscopy (SEM) and X-ray diffraction (XRD) analysis. The adhesion between the film and substrate was evaluated by using adhesive tape test. It was found that the presence of TiO₂ dramatically enhanced the adhesion strength between the film and the substrate, as well as the deposition rate of film. The mechanism for the deposition of Au/TiO₂ film was also discussed.     

环境光对PE塑料薄膜近红外激光拉曼光谱的影响

探讨了环境光自然光和室内荧光灯光的存在,对PE透明塑料薄膜的近红外激光拉曼光谱的影响.研究表明不同的环境光,会对近红外拉曼光谱产生不同的明显特征峰.自然光干扰产生的是以倒峰群形式为主,而室内荧光灯光造成的干扰主要以尖锐的脉冲峰形式.虽干扰表现形式不同,但都有严重地影响,在测定时一定要引起重视,不能忽略.建议在进行透明塑料近红外拉曼光谱检测时,须在暗室或暗罩遮光保护中进行,以完全隔离环境光的影响.     

金刚石窗口冷却Yb3+∶YAG DPSSL设计

针对高功率二极管重复率抽运的V型非稳腔Yb3+∶YAG激光头，提出了利用金刚石窗口冷却和直接水冷相结合的复合冷却设计.在YAG片的抽运面进行直接水冷，同时在激光提取面利用金刚石窗口冷却介质.金刚石优异的导热性能不仅能够有效地冷却激光介质，还能消除横向的温度梯度，解决了高功率激光器冷却和高功率抽运的矛盾.模拟结果表明对掺杂10 at %厚度为1.6 mm的Yb3+∶YAG片在抽运功率密度为20 kW/cm2，重复频率为10 Hz的条件下，要将最高温度控制在可接受的范围内（比如320 K），周围冷却水的对流换热系数约为4000 W/m2K.