Preparation of a novel Ni/Co-based alloy gradient coating on surface of the crystallizer copper alloy by laser

A high wear-resistant gradient coating made of Ni/Co-based alloys on the surface of a Cu alloy substrate was synthesized using a YAG laser induced in situ reaction method. The coating consists of three layers: the first is a Ni-based alloy layer, the second and third are Co-based alloy layers. The microhardness increases gradually from 98 HV in the Cu alloy substrate to the highest level of 876 HV in the third layer. The main phase of the Co-based alloy layer is CoCr₂(Ni,O)₄, coexisting with the Fe₁₃Mo₂B₅, Cr(Co(Mo, and FeCr_0.29Ni_0.16C_0.06 phases. Wear tests indicate that the gradient coating has good bond strength and wear properties with a wear coefficient of 0.31 (0.50 for the Cu alloy substrate). Also, the wear loss of the coating is only 0.01 g after it has been abraded for 60 min, which is only one fifth of that of the Cu alloy of the crystallizer. Wear tests of the gradient coating reveal good adhesive friction and wear properties when sliding against steel under dry conditions. This novel technique may have good application to make an advanced coating on the surface of the Cu alloy crystallizer in a continuous casting process.     

激光产生蒸汽羽的干涉研究

 根据拍摄1.06 μm长脉冲钕玻璃激光与LY12铝靶耦合产生蒸汽羽的干涉分幅照片，测出在t<50 μs空气冲击波速度约为473 m/s而蒸汽羽阵面扩散速度约为162 m/s。运用蒸汽羽等离子体的有关热力学特性方程组，得到蒸汽羽等离子体的电子密度、电子温度、电离度和吸收系数的最大值分别为N_e≈3.1×10¹⁷ cm^-1，T≈6 096 K，η≈0.014，α_(1.06μm)≈0.03 cm^-1的结果。     

Site symmetry and crystal field splittings of Ce 3+ in LiLuF 4 and LiSr 0.8 Ca 0.2 AlF 6

Electron paramagnetic resonance (EPR) spectra of Ce 3+ in LiLuF 4 (LLF) and LiSr 0.8 Ca 0.2 AlF 6 (LSCAF) observed at low temperatures (<20 v K) show that the Ce 3+ centers have tetragonal and pseudo-trigonal symmetry with ( g , g )=(2.751, 1.467) and (2.14, 0.80), respectively. The EPR lines of Ce 3+ in LSCAF are inhomogeneously broadened by different Ce 3+ configurations which correspond to the random occupation of the second nearest neighbor cation sites by Ca 2+ and Sr 2+ and/or charge compensators. These EPR results indicate that the Ce 3+ centers in LLF and LSCAF are associated with substitution of Ce 3+ for Lu 3+ with eight-fold coordination and Sr 2+ /Ca 2+ with six-fold coordination, respectively. Fourier transform infrared absorption has been used to measure transitions between the 2 F 5/2 ground state and the 2 F 7/2 multiplet of Ce 3+ in LLF at 10 v K. The optical absorption and luminescence of Ce 3+ :LLF and Ce 3+ :LSCAF in the UV range are strongly polarized. The energy levels and polarization dependence of the optical transitions can be accounted for in terms of the crystal field potential experienced by the Ce 3+ ions under the action of the different point group symmetries.     

Effect of laser irradiation on the electrical properties of dysprosium doped LiCo-Ferrite

The effect of laser irradiation on the electrical properties of Li_0.5+z Co _z Dy _x Fe_2.5?2z?x O₄ ferrite (0.0 ≤ x ≤ 0.2, z = 0.1) has been studied in the temperature range 300 K ≤ T ≤ 750 K at frequencies of 10 kHz?5 MHz, using a LIMO-IR laser diode, at a wavelength of 808 nm. It was found that laser irradiation increases the polarization, the resistivity and the paramagnetic region. As the result of electronic rearrangement and lattice defects, small polorons and clusters were created. The doping of LiCo-Ferrite by Dy³⁺ increases both the AC and DC resistance of the investigated material. The variation of the AC and DC resistance with the Dy-content (x) obeys the following correlations R _ac/100 = 50x ²+4x+0.005 and R _dc/1000 = 31x ²+0.099x+0.09, respectively. A peculiar behaviour was obtained for the sample with Dy-content x = 0.075, as the resistance notably decreases. The applicable result is that laser irradiation increases the resistance of LiCo-ferrite by about 17% while its doping by dysprosium at x = 0.15 increases the resistance by about 23%. Its value is nearly stable for the temperature range from 340 to 480 K.     

Propagation characteristics of tilted partially coherent rectangular flat-topped beam in turbulent atmosphere

In this paper, the effects of atmospheric turbulence on the intensity distribution of a tilted Rectangular Partially Coherent Flat-Topped (RPCFT) beam were studied. An analytical formula for the intensity distribution was derived. POWER In Bucket (PIB) value is calculated numerically. The effects of source parameters – such as correlation length, order of flatness and tilt coefficient – on the intensity were analyzed. Detailed analysis demonstrates that these parameters have an influence on beam propagation properties. The analyses are illustrated by numerical examples and graphs.     

1 319和1 338 nm双波长Nd:YAG脉冲激光输出实验研究

 根据计算得到的双波长激光振荡的阈值条件,激光实验中对全反镜镀制1 319和1 338 nm的全反膜（其反射率大于99.73%,而对1 064 nm激光的反射率约为7%）;输出镜采用对1 064 nm强谱线95%的高透过率,而对1 319和1 338 nm谱线的透过率分别为34.7%,32.5%,有效抑制了强线1 064 nm振荡,成功实现了1 319和1 338 nm Nd:YAG同时双波长激光脉冲输出。当输入能量为125 J时,1 319和1 338 nm脉冲双波长激光的单脉冲总输出能量为0.89 J,电-光转换效率为0.71%,斜率效率为0.89%。输出的双波长激光的中心波长分别在1 318.8和1 338.2 nm处,谱线宽度（FWHM）分别为0.35和0.48 nm,强度之比为36:44。     

应用理性优化蚁群算法提高激光三维复制的重现度

三维复制人工耳和打印手枪把激光三维复制技术推向新的一页。激光三维扫描是激光应用中一个新兴的重要领域,在三维复制中扮演着无可替代的角色,其复制精度在目前所有复制技术中是最高的。而重现度标志着复制结果与复制对象几何形状上的一致程度,是激光三维复制最重要的指标。分析了激光三维复制的误差,得出激光扫描的点云数据处理是减小误差、提高重现度的关键所在的结论。主要创新点在于,在传统蚁群算法的基础上,将提出理性优化蚁群算法应用于激光三维复制中的数据处理。经计算对比发现,有效减小了复制的误差,提高了复制的重现度。     

基于高速肖特基二极管的100 ps瞬态取样门设计与仿真

 皮秒级瞬态取样门主要应用于激光聚变实验和高能物理实验中,对单次高速脉冲进行实时取样。提出了一种新颖的基于肖特基二极管桥的平衡取样门,给出其模型和具体电路设计。电路仿真结果表明,对称的选通设计保证了选通脉宽为100 ps时,取样间隔也为100 ps,取样门带宽为4.4 GHz,可应用于多路超短激光脉冲取样。     

Compton散射下强激光等离子体空气冲击波波前的传输特性

 根据球对称激光等离子体空气冲击波在自由空间中传输的约束条件,对多光子非线性Compton散射的强激光等离子体空气冲击波波前的传输特性进行了研究,给出了散射下空气冲击波波前的运动方程,并进行了数值模拟。结果表明：该冲击波的衰减过程不仅与爆炸源和爆炸过程的特性、释放总能量、空气的弹性有关,而且还与散射有关,散射效应使冲击波的初始半径增大,衰减过程加快,能量转移率提高;数值模拟与实验结果符合得很好。