全彩LED大屏幕视频图像信号的校正

全彩ＬＥＤ大民间葜可以用来显示电视画面。由于ＣＲＴ发光特性的非线笥,在图像信号源处引入一种称为γ校正的相反预失真来补偿ＣＲＴ的这种非线性。但由于全彩ＬＥＤ大屏幕系统的发光特性与ＣＲＴ的发光特性不同,它的发光亮度与其控制量成线性关系,因此在显示电视画面时会引适合ＬＥＤ屏的显示。此外,还考虑到人的视觉的明亮度与物理亮度的关系。本文给出了一种对ＬＥＤ大屏幕信号进行校正的方法,即γ校正,实验结果表明效果极     

HETEROJUNCTION DIODES OF POROUS SILICON WITH SOLUBLE POLYANILINE*

Two kinds of heterojunction diodes of porous silicon (PS) with soluble polyaniline (PANI) werefabricated. One is a heterojunction diode of PS with water-soluble copolymer of polyaniline (PAOABSA),Al/PS-PAOABSA/Au cell as rectifying diode. Another is a heterojunction diode of PS with solublepolyaniline doped with DBSA, Al/PS-PANI (DBSA)/Au cell as light emitting diode (LED). The rectifyingcharacteristics of the rectifying diodes were measured as a function of the degree of sulfonation and thicknessof the copolymers, as well as oxidation of PS. The rectifying ratio of the heterojunction can reach 5.0×10~4 at±3 V bias. For the LED, the photoluminescence (PL) and electroluminescence (EL) spectra were measuredand discussed.     

The influence of window layers on the performance of 650 nm AlGaInP/GaInP multi-quantum-well light-emitting diodes

In this article, we investigate the influence of AlGaAs and GaP window layers on the device performance of 650 nm AlGaInP/GaInP multi-quantum-well (MQW) light-emitting diodes (LEDs) grown by metalorganic chemical-vapor deposition. The AlGaInP/GaInP MQW structure with different window layers are characterized by double-crystal X-ray diffraction, secondary ion mass spectrometry and photoluminescence. By using the AlGaAs window layer, the LEDs have a lower cut-in voltage, a smaller dynamic series resistance and a higher breakdown voltage, while the LEDs with a GaP window layer show a stronger electroluminescence intensity, a higher light output power, a higher external quantum efficiency and a slower degradation of light output with increasing bias current. These results indicate that the GaP material is more adequate to be used as a window layer for the AlGaInP optical devices.     

Degradation effects in polymer light emitting devices due to heat treatment

The characteristics of polymer light emitting diodes (PLEDs) (ITO/PPV/Ca) depend strongly on the conditions during preparation and operation. We studied the effects of heat treatment (during and after preparation) of PLEDs with OC₁C₁₀-PPV as active layer. PLEDs showed a reduction of both the current and the light output to 40 % after annealing for only 30 min at 65 °C. Effects on I-V characteristics were studied by measuring single carrier devices (hole- and electron-dominated devices). The current reduction after heat treatment can be ascribed to degradation of the ITO/PPV and the Ca/PPV interfaces.     

SrSnO_3:Eu~(3+)红色荧光粉的合成及发光性能的研究

通过传统的高温固相法成功合成了SrSnO_3∶Eu~(3+)红色荧光粉。通过对样品X射线衍射图谱、激发发射图谱和衰减曲线的研究,证明了合成的SrSnO_3∶Eu~(3+)红色荧光粉是纯相而且具有良好的发光性能与热稳定性。SrSnO_3∶0.05Eu~(3+)荧光粉在396 nm激发下Eu~(3+)通过~5D_0→~7F_2能级跃迁,在614 nm处发出比较强烈的红光,色坐标为(0.608,0.386),通过计算得出温度猝灭的活化能ΔE=0.138 e V。综上所述,SrSnO_3∶Eu~(3+)荧光粉是一种比较有前途的白色LED用近紫外蓝光激发红色荧光粉。     

多基色混合白光LED显色性优化研究

为优化多基色混合白光LED的显色性,得到色彩生动的白光LED照明效果,以评价饱和红色的特殊显色指数R₉为研究对象,通过多基色光源混合白光LED的光谱功率分布的高斯数学模型,选取峰值波长λ_m、半波宽Δλ和幅值A为基色光源光谱功率分布的主要参量,并以“蓝光芯片+YAG黄色荧光粉”和“红、绿和蓝基色LED”为分析模型分别进行二基色和三基色混合白光LED显色性研究,讨论两种基色混合情况下三个参量对混色白光LED的显色性R₉贡献。结果表明：为使多基色混合白光LED的显色性更好,首先确定光源S1的峰值波长λ_m1、半波宽Δλ₁及幅值A₁;然后设定其他基色光源幅值A_i以求此条件下峰值波长λ_mi和半波长Δλ_i取值范围;最后在求得的峰值波长λ_mi和半波长Δλ_i取值范围,反求基色光源的最佳幅值A_iopt,从而使多基色混合白光LED的显色性达到最佳效果。该方法对分析基色混合白光LED的显色性具有理论参考价值。     

一种大功率LED散热系统模糊控制器设计

基于当前的COB封装LED芯片,分析了芯片的热阻模型,推导出发光结在理想温度下工作时的基板温度。针对大功率LED存在的散热问题,基于课题组双进双出射流冲击水冷散热系统,设计了一种模糊控制器,选取温度变化和温度变化率为控制输入量,并对各控制输入量的范围设定进行了说明。根据设计的控制器进行程序编写,下载到控制芯片中进行实际验证,在20℃环境温度下,芯片基板温度最终维持在35.5~36.5℃之间,保证了灯具正常、稳定工作,为大功率LED散热系统提供了一种控制器设计方案,具有一定的实际意义。     

近场照度均匀的LED阵列设计

通过分析多颗LED组成的各种阵列在近场平面上的照度分布,来设计可实现近场照度均匀的LED排列方式和距离。基于LED的光强分布,构建单颗LED的光强分布模型（并非朗伯分布）,给出了方程和等式用于计算不同排列方式下的LED分布距离和封装密度,以实现近场平面上的照度均匀。     

Nonspherical LED packaging lens for uniformity improvement

Light emitting diode (LED) has more advantages compared with a traditional incandescent light bulb and a fluorescent lamp, such as small size, low quantity of heat, long life, low power consumption, fast response, plain packaging and ease of develop ment of a frivolous short product. A methodology is proposed to improve the uniformity of the LED illumination system. As a light source in a backlight unit (BLU), the requirement for optical characteristics of a LED is different from highly directional conventional ones. New diffused-type LEDs need to be developed to fulfill the requirement of the BLU industry. A non-spherical lens is designed to optimize uniformity, and a great improvement in uniformity from 28.4 to 64% is demonstrated. In the future, it may used in an LED display to improve the unevenness of illumination.     

基于白光LED照明光源的室内VLC系统

LED照明与可见光通信技术相结合,构建出基于LED可见光无线通信系统。对室内VLC(Visible Light Communication)系统的白光LED光源特性和系统信道模型分析,提出照明光源布局设计与接收光功率分布的关系;对强度调制直接检测方式的室内VLC系统中信噪比和多径效应引起的码间串扰分析,提出采用光分集接收技术克服码间串扰和提高信噪比,并给出光检测器阵列布局的模型。建立VLC系统仿真模型,给出OOK-NRZ (On-Off Keying & Non-Return Zero)和OOK-RZ(On-Off Keying & Return Zero)调制方式的误码率和均方根时延扩展之间的关系曲线。仿真结果表明,接收光功率相同时,均方根时延扩展时间大于1.0 ns时,OOK-RZ特性优于OOK-NRZ。