Processing of lignocellulosic polymer wastes using microwave irradiation

Lignin and mixed lignocellulosic natural polymer wastes have been accumulated in landfills over the past hundred years. These wastes should be processed to produce added- value chemicals and materials. This mini-review presents a brief literature survey related to state-of-the-art methods developed recently by the world research community to solve the problem of rational conversion of lignocellulosic polymer wastes, including production of hydrogen, synthesis gas, phenols, and monomers. The focus is made on microwave and plasma technologies used for lignocellulosic wastes processing.     

Study of water uptake in poly(ether ether ketone) irradiated by MeV O+ and Au+ ions

Poly(ether ether ketone) (PEEK) was irradiated with 4?MeV O⁺ and 5 and 10?MeV Au⁺ ions to the fluences from 10¹² to 10^14?cm^?2 and then treated in 5 M/l water solution of LiCl for one month at room temperature. After drying and removal of LiCl surface contamination, the depth distribution of LiCl embeded in PEEK was measured by the neutron depth profilig method (NDP) sensitive to ⁶Li isotope. Embeded LiCl is believed to map distribution of water diffusing into PEEK interior. The results show that the PEEK irradiated to the fluences above 1.10¹³cm^?2 is prone to water penetration to the depths of few microns. On the pristine PEEK and that irradiated to lower ion fluences only a surface Li contamination is observed.     

Insight into copper-mordenite–silica mixtures (CuMOR–SiO2)

A series of ternary CuMOR–SiO₂ mixed materials were prepared by two synthesis approaches (CuMOR1–y–SiO₂ and CuMOR2–y–SiO₂). Extensive characterization was done for both series and some selected materials were tested in CO catalytic oxidation and NO reduction. The presence of CuMOR and SiO₂ segregated phases was observed in both series by XRD, suggesting that silica formation was not inhibited by the mordenite (MOR) presence. UV–Vis results exhibited that Cu ion exchange was successfully done for CuMOR1–y–SiO₂ series. In the CuMOR2–y–SiO₂ series, the amount of copper was below the sensitivity limit of EDS analysis. CuMOR1–50%–SiO₂ catalyst resulted with higher specific surface area and catalytic activity. A possible relation between reduction temperature, the increase in Cu plasmon excitation, and catalytic activity was observed.     

Unraveling the Mechanisms of the Excited-State Intermolecular Proton Transfer (ESPT) for a D-π-A Molecular Architecture

Precise revealing the mechanisms of excited-state intermolecular proton transfer (ESPT) and the corresponding geometrical relaxation upon photoexcitation and photoionization remains a formidable challenge. In this work, the compound (E)-4-(((4H-1,2,4-triazol-4-yl)imino)methyl)-2,6-dimethoxyphenol (TIMDP) adopting a D-π-A molecular architecture featuring a significant intramolecular charge transfer (ICT) effect has been designed. With the presence of perchloric acid (35 %), TIMDP can be dissolved through the formation of a HClO₄–H₂O–OH(TIMDP)–N(TIMDP) hydrogen-bonding bridge. At the ground state, the ICT effect is dominant, giving birth to crystals of TIMDP. Upon external stimuli (e.g., UV light irradiation, electro field), the excited state is achieved, which weakens the ICT effect, and significantly promotes the ESPT effect along the hydrogen-bonding bridge, resulting in crystals of [HTIMDP]⁺ ⋅ [H₂O] ⋅ [ClO₄]⁻. As a consequence, the mechanisms of the ESPT can be investigated, which distorted the D-π-A molecular architecture, tuned the emission color with the largest Stokes shift of 242 nm, and finally, high photoluminescence quantum yields (12 %) and long fluorescence lifetimes (8.6 μs) have achieved. These results not only provide new insight into ESPT mechanisms, but also open a new avenue for the design of efficient ESPT emitters.     

Facile preparation of superhydrophobic nanorod surfaces through ion-beam irradiation

Obtaining superhydrophobic surfaces for their application in electronics and flexible wearable devices remains a significant challenge. Most previously reported methods for obtaining superhydrophobic surfaces involve complex and expensive preparation techniques and thus cannot be used for practical applications. Ion-beam irradiation is a simple and promising method for fabricating superhydrophobic nanostructures on large areas at a low cost. Ion-beam irradiation using argon and oxygen gases was used to prepare silica nanorod structures on glass substrates. This study is not just a modification of the surface of nanoparticles, but a change in nanoparticle shape. The nanorods were subsequently treated with perfluorooctyltriethoxysilane to obtain superhydrophobicity. The surface of the silica nanorods exhibited a static water contact angle of 153°, indicating superhydrophobicity. The combination of rough structures of silica nanorods and low surface energy resulted in superhydrophobicity. The surface properties were evaluated in detail using Fourier-transform infrared spectroscopy, field-emission scanning electron microscopy, and X-ray photoelectron spectroscopy. The proposed method is facile, inexpensive, and can be used for the large-scale production of nanorod structures for potential industrial applications.     

Radical processes initiated by ionizing radiation in PEEK and their macroscopic consequences

Poly (ether ether ketone) was irradiated with gamma rays or electron beam to investigate the radical process. The generated paramagnetic species were observed by electron spin resonance spectroscopy at ambient temperature and in liquid nitrogen. The effect of microwave power on saturation of the particular spectra and thermal annealing effects were determined. The following radicals were identified: radical anion, phenoxyl radical, and phenylperoxy radical. Despite the fact that the intermediates were formed as a result of backbone cleavage causing degradation, the macroscopic features were almost unaffected by irradiation up to dose of 1500 kGy.