NH4F对NH3低温选择性催化还原NO的影响研究

制备了一种新的氟掺杂氧化钒/氧化钛催化剂,探讨了掺杂模式、制备方法对低温SCR活性的影响.结果显示,在120~240℃反应温度下,由溶胶法制得的氟掺杂于钒(F-V)模式下的催化活性最佳,通过与未掺杂催化剂(COM)对比可知,在210℃时,氟掺杂催化剂的活性提高了35%,并于240℃时NO的脱除率达到了98.6%.通过X射线衍射试验(XRD)、透射电子显微镜(TEM)、比表面积测试(BET)、光电子能谱分析(XPS)以及H_2程序升温还原(H_2-TPR)等表征技术显示氟掺杂引起催化剂SCR活性提升主要与催化剂活性成分的良好分散性、粒子尺寸减小、比表面积及孔容增大、更强的氧化还原能力有关.另外,通过试验研究表明,氟掺杂催化剂不仅提升了SCR活性,拓宽了活性温度范围,而且还增强了抗硫与抗水性能.     

Gd0.2Ce0.8O1.9纳米颗粒对固体氧化物电解池La0.6Sr0.4Co0.2Fe0.8O3-δ阳极 析氧反应的影响

化石燃料的使用排放了大量CO2,对气候和环境造成了日益严重的危害.固体氧化物电解池(SOEC)能够利用可再生能源产生的电能将CO2高效转化成CO,降低CO2排放的同时,又能减少化石燃料的使用,近年来受到研究者的广泛关注.相比于低温液相CO2电还原,SOEC高的运行温度保证了其较高的反应速率,即较高的电流密度.典型的SOEC单电池由多孔阴极、致密电解质和多孔阳极以三明治的方式组装而成.CO2分子在阴极得到两个电子解离成CO和一个O2–;生成的O2–通过致密电解质传导至阳极,在阳极失去四个电子发生析氧反应(OER)生成一个O2.相比于两电子的阴极反应,阳极四电子的析氧反应更难进行,可能是整个电极过程的速控步,因此开发高性能的阳极材料有望显著提高SOEC的CO2电还原性能.La0.6Sr0.4Co0.2Fe0.8O3-δ(LSCF)因具有较高的混合离子-电子导电性而被用作SOEC阳极材料,但受LSCF-气体两相界面的限制,其OER性能较低.研究表明,LSCF-掺杂的CeO2-气体所构成的三相界面相比于LSCF-气体两相界面具有更高的电化学反应活性,即OER反应更易在三相界面进行.因此,本文将Gd0.2Ce0.8O1.9(GDC)纳米颗粒浸渍到SOEC LSCF阳极来提高其OER活性,考察了纳米颗粒浸渍量(3,5,10和20 wt%)对SOEC电化学性能的影响.结果表明,SOEC的电化学性能随浸渍量的增加而逐渐升高,当GDC纳米颗粒浸渍量为10 wt%时(10GDC/LSCF),SOEC的电化学性能达到最高,在800 oC和1.6 V的电流密度为0.555 A cm–2,是LSCF阳极SOEC性能的1.32倍.继续增加浸渍量到20 wt%,电化学性能反而开始下降.电化学阻抗谱测试结果表明,GDC纳米颗粒的加入减小了SOEC的极化电阻.对应的弛豫时间分布函数解析结果表明10GDC/LSCF阳极上的OER由四个基元反应构成.电镜和O2-程序升温脱附结果表明,GDC纳米颗粒的加入显著增加了10GDC/LSCF阳极三相界面和表面氧空位的数量以及体相氧的流动性,从而促进了OER四个基元反应的反应速率,降低了这几个过程的极化电阻,因而降低了OER反应的极化电阻,提高了SOEC电还原CO2的电化学性能.     

The synthesis of a [2.2]paracyclophane-derived secondary phosphine oxide and a study of its reactivity

A planar chiral secondary phosphine oxide based on [2.2]paracyclophane was synthesized and its chemistry investigated; it was shown to be a competent pre-ligand in palladium(0)-mediated reactions, and displayed promising activity in gold(I)-catalysed cyclisations. The secondary phosphine oxide could be transformed into a collection of P-stereogenic tertiary phosphine oxides. These are rare examples of the planar chirality of [2.2]paracyclophane being combined with a P-stereogenic centre. Unfortunately, epimerisation of the phosphorus stereocentre during reduction limits the use of this chemistry.     

Graphene oxide (GO) catalyzed transamidation of aliphatic amides: An efficient metal-free procedure

Transamidation involves direct interconversion of an amide with amine, and represents an alternative to the common method of amide formation from the reaction of carboxylic acid with an amine. While the carboxamides have huge potential in biological systems and polymer industries, their formation from carboxylic acids requires activation by a suitable catalyst. A metal-free transamidation of aliphatic amide with aromatic amine catalyzed by graphene oxide (GO) has been developed and established as a general, synthetically useful and selective procedure. Graphene oxide bearing several carboxylic acids on the edges and having large surface area acts as an efficient and recyclable catalyst for transamidation.     

K促进的纳米片状水滑石衍生CoAlO金属氧化物催化碳烟燃烧

采用水热法合成了负载K的纳米片状水滑石衍生CoAlO金属氧化物,其表现出优异的催化碳烟燃烧活性.氢气-程序升温还原（H₂-TPR）实验结果表明,K与Co之间的相互作用提高了催化剂的氧化还原性能.X射线光电子能谱（XPS）分析结果表明,K的负载增大了表面Co²⁺/Co³⁺的比例,促进了氧空位的产生,提高了催化剂对气相氧的吸附能力.碳烟-程序升温还原（Soot-TPR）实验结果表明,K的负载增加了表面吸附氧数量.动力学实验结果表明,K的负载增加了单位质量催化剂上的活性氧数量、反应速率和转化频率（TOF）,从而提高了催化剂的本征活性.另外,碳烟颗粒可以分散在纳米片的层间,与活性位点的接触效率得到提高,也有利于提高催化碳烟燃烧活性.     

Effect of ethyl‐bridged diphenylphosphine oxide on flame retardancy and thermal properties of epoxy resin

Three commercialized flame retardants, 1,2‐bis(diphenylphosphinoyl)ethane (EDPO), 6,6‐(1,2‐phenethyl)bis‐6H‐dibenz[c,e][1,2]oxaphosphorin‐6,6‐dioxide (HTP‐6123), and hexa‐phenoxy‐cyclotriphosphazene (HPCTP), were used to prepare the flame retardant diglycidyl ether of bisphenol A (DGEBA) epoxy resin (EP) under the same experimental conditions. The effects of T_g, thermal stability, and water absorption properties of EP caused by the three flame retardants were investigated and compared, together with their flame retardant efficiency. Results showed that the introduction of the three flame retardants improved the flame retardant performance of EP but led to decreases in T_g and decomposition temperature. EDPO showed higher flame retardant efficiency than the other two flame retardants. EP/EDPO showed higher thermal stability, better flame retardant performance, higher T_g value, and lower water absorption than EP/HTP‐6123 and EP/HPCTP. The study discovered that EDPO and HTP‐6123 primarily act through the gas phase flame retardant mechanism, while HPCTP is primarily driven by the condensed phase mechanism.     

碳化终温对β-Mo2C催化喹啉加氢脱氮性能影响

以MoO_3为前驱物,CH_4/H_2为碳源,采用程序升温直接还原碳化法制备不同碳化终温(640、660、680、700和720℃)的碳化钼催化剂,通过XRD、N_2吸附-脱附、SEM、TEM、XPS和Raman表征研究碳化钼的物理性质和结构性质,并研究不同碳化终温碳化钼对喹啉加氢脱氮的催化性能。结果表明,不同碳化终温的碳化钼催化剂均为β-Mo_2C,碳化终温可显著改变碳化钼表面物种含量、平均孔径和介孔分布。碳化终温为680℃时,催化剂碳化程度较高,表面氧物种含量最低,表面C/Mo物质的量比最高,对应的催化活性也最佳,在340℃、4 MPa条件下,喹啉的转化率和脱氮率均高达99%以上,芳香族类化合物的选择性可达37.8%,显示出较低的芳环破坏性。表面组成尤其是表面氧对于β-Mo_2C上喹啉加氢脱氮反应途径的调控至关重要。     

Detection of Dexamethasone Sodium Phosphate in Blood Plasma: Application of Hematite in Electrochemical Sensors

We studied sensor application of a graphene oxide and hematite (α‐Fe₂O₃/GO) composite electrode well‐characterized by the SEM and XRD. Through differential pulse voltammetry (DPV), oxidation of dexamethasone sodium phosphate (DSP) was studied at the surface of a glassy carbon electrode (GCE) modified with graphene oxide nanosheets (GO) and the α‐Fe₂O₃/GO composite. The values of the transfer coefficient (α) and the diffusion coefficient (D) of DSP were 0.5961 and 4.71×10^?5 cm² s^?1 respectively. In the linear range of 0.1–50 μM, the detection limit (DL) was 0.076 μM. In the second step, a GCE was modified with α‐Fe₂O₃/GO composite and the DSP measurement step was repeated to analyzed and compare the effects of hematite nanoparticles present on graphene oxide surfaces. According to the results, α and D were 0.52 and 2.406×10^?4 cm² s^?1 respectively and the DL was 0.046 μM in the linear range of 0.1–10.0 μM. The sensor is simple, inexpensive and uses blood serum.     

ZnO纳米管有序阵列与Cu2O纳米晶核壳结构的光电化学性能及全固态纳米结构太阳电池研究简

采用电化学方法在铟锡氧化物(ITO)导电玻璃基底上制备了高度有序的ZnO纳米管阵列,然后在ZnO纳米管阵列上电化学沉积Cu2O纳米晶颗粒,获得了一维有序Cu2O/ZnO核壳式纳米阵列结构,通过控制Cu2O纳米晶的沉积电量得到不同厚度的Cu2O壳层,并对该核壳式纳米阵列的形貌和结构进行了分析. 以Cu2O/ZnO一维核壳式纳米阵列结构为光电极组装全固态纳米结构太阳电池,研究了Cu2O壳层厚度对光电极光吸收性能、光电性能以及组装电池光伏性能的影响,优化了电池中对电极材料的喷金厚度. 结果表明,以Cu2O沉积电量为1.5 C的Cu2O/ZnO为光活性层,以4 mA电流下真空镀金20~25 min的铜基底为对电极组装的简易太阳电池最高可获得0.013%的光电转换效率.     

过渡金属氧化物修饰石墨毡阴极及电催化氧化性能测试

采用H2O2化学预处理石墨毡,并将过渡金属氧化物Ce O2负载到石墨毡上,制备出复合石墨毡阴极材料。研究结果表明H2O2处理可增加石墨毡的含氧官能团,改善表面亲水性,进而提高Ce O2的负载量,XRD分析表明石墨毡表面负载的Ce O2为萤石结构。电化学阻抗谱(EIS)和循环伏安曲线(CV)分析表明修饰后的石墨毡电荷传输阻力变小,氧化还原电流强度显著增强,活性表面积增大8倍,线性扫描(LSV)实验表明改性石墨毡在氧还原过程中具有较大的电流密度,是未改性前的8.5倍。采用改性石墨毡作为阴极,进行电芬顿催化降解甲基橙测试,20 min脱色率达到96.8%,与未改性石墨毡相比,去除率提高133.2%,显著提高了其电催化氧化性能。