Site location and requirements for the installation of a nuclear magnetic resonance scanning unit

The installation of a nuclear magnetic resonance unit in any diagnostic facility involves certain location and environmental requirements. Based on our experience with the FONAR QED 80 system, we have delineated the major factors which must be considered when planning for such an installation. The major requirements are location and space. Suggested layouts for the suite and the control room are included. Certain environmental specifications will vary depending on the location of the facility and the type of unit installed.     

Magnetic fields associated with a nuclear magnetic resonance medical imaging system

Measurements were made of magnetic and electric field levels in and around a nuclear magnetic resonance imaging system undergoing a clinical trial. Magnetic field levels ranged from 0.04 tesla (T) in the imaging volume down to about 0.0006 T at the end of the patient table. The peak radio-frequency magnetic field level was 15 amperes per meter (A/m) in the imaging volume, while the rms value was 4.6 A/m. The specific absorption rate resulting from the radio-frequency magnetic field was calculated to be no more than 0.017 watts per kilogram (W/kg). The radio-frequency electric field was detectable only within a few centimeters of the coil assembly, and does not significantly contribute to the specific absorption rate. These exposure levels were much lower than existing guidelines for clinical NMR procedures.     

A magnetic resonance device designed via global optimization techniques

In this paper we are concerned with the design of a small low-cost, low-field multipolar magnet for Magnetic Resonance Imaging with a high field uniformity. By introducing appropriate variables, the considered design problem is converted into a global optimization one. This latter problem is solved by means of a new derivative free global optimization method which is a distributed multi-start type algorithm controlled by means of a simulated annealing criterion. In particular, the proposed method employs, as local search engine, a derivative free procedure. Under reasonable assumptions, we prove that this local algorithm is attracted by global minimum points. Additionally, we show that the simulated annealing strategy is able to produce a suitable starting point in a finite number of steps with probability one.This work was supported by CNR/MIUR Research Program Metodi e sistemi di supporto alle decisioni, Rome, Italy.Mathematics Subject Classification (1991):65K05, 62K05, 90C56     

Minimum energy pulse synthesis via the inverse scattering transform

This paper considers a variety of problems in the design of selective RF-pulses. We apply a formula of Zakharov and Manakov to directly relate the energy of an RF-envelope to the magnetization profile and certain auxiliary parameters used in the inverse scattering transform (IST) approach to RF-pulse synthesis. This allows a determination of the minimum possible energy for a given magnetization profile. We give an algorithm to construct both the minimum energy RF-envelope as well as any other envelope that produces a given magnetization profile. This includes an algorithm for solving the Gel'fand-Levitan-Marchenko equations with bound states. The SLR method is analyzed in terms of traditional scattering data, and shown to be a special (singular) case of the IST approach. RF-envelopes are computed for a variety of examples.     

An open volume, high isolation, radio frequency surface coil system for pulsed magnetic resonance

We present an open volume, high isolation, RF system suitable for pulsed NMR and EPR spectrometers with reduced dead time. It comprises a set of three RF surface coils disposed with mutually parallel RF fields and a double-channel receiver (RX). Theoretical and experimental results obtained with a prototype operating at about 100 MHz are reported. Each surface RF coil (diameter 5.5 cm) was tuned to f₀ = 100.00 ± 0.01 MHz when isolated. Because of the mutual coupling and the geometry of the RF coils, only two resonances at f₁ = 97.94 MHz and f₂ = 101.85 MHz were observed. We show they are associated with two different RF field spatial distributions. In continuous mode (CW) operation the isolation between the TX coil and one of the RX coils (single-channel) was about −10 dB. By setting the double-channel RF assembly in subtraction mode the isolation values at f₁ or f₂ could be optimised to about −75 dB. Following a TX RF pulse (5 μs duration) an exponential decay with time constant of about 600 ns was observed. The isolation with single-channel RX coil was about −11 dB and it increased to about −47 dB with the double-channel RX in subtraction mode. Similar results were obtained with the RF pulse frequency selected to f₂ and also with shorter (500 ns) RF pulses. The above geometrical parameters and operating frequency of the RF assembly were selected as a model for potential applications in solid state NMR and in free radical EPR spectroscopy and imaging.     

Modeling and Simulation of Saturation Gain of IR Integrated Photonic Amplifiers

IR integrated photonic amplifiers at 1.55m operation will have good foreground in optical phasedarray radars for splitters and signal processing. The saturation gain characteristics of IR integrated photonic waveguide amplifiers (taken Er³⁺Yb³⁺ co-doped phosphate glass waveguide amplifiers as an example) are studied theoretically. For the homemade laser glass materials the calculated saturation intensities are 2.22kw /cm² for signal and 10.15kw/cm² for pump. The effects of absorption saturation of signal and pump lights on the gain of amplifiers are discussed.     

高频地波雷达频谱监测系统的前端电路设计

利用超外差式接收和直接数字合成(DDS)技术设计了高频地波雷达频谱监测系统的前端电路．该电路能够根据雷达探测距离的远近选择相对应的噪声信号接收频段,为后续的数据采集与处理提供噪声电平数据．实验证明：本系统的跳频本振信号信噪比(SNR)优于60dB;对输入信号具有60dB左右的增益和1μV的灵敏度,满足了武汉大学研制的下一代高频地波海态监测雷达对频谱监测的需要．     

Quantitative, dynamic fuel distribution measurements in combustion-related devices using laser-induced fluorescence imaging of biacetyl in iso-octane

Knowledge of in-situ fuel distributions in practical combustion devices, such as internal combustion engines, is crucial for research and devlopment purposes. Numerous imaging techniques, mostly based on laser-induced fluorescence (LIF), have been developed and yield high levels of 2-D spatial information, but generally lack the temporal resolution (frame rates) necessary to resolve important timescales at sub-millisecond levels for sustained times. A planar LIF technique for quantitatively visualizing fuel distribution is presented which gives not only high spatial resolution, but also high temporal resolution. Using a high-speed CMOS camera, a lens-coupled image intensifier, and frequency-tripled diode-pumped Nd:YAG laser allows for capturing LIF images of biacetyl that is used as a fluorescence tracer at 12 kHz (one crank-angle resolution at 2000 RPM) for hundreds of consecutive engine cycles. The LIF signal strength of biacetyl doped in iso-octane is shown to vary substantially over a wide range of temperatures and pressures. The low absorption coefficient at 355 nm and a longpass filter in the detection path exclude bias errors due to laser beam attenuation and fluorescence trapping. An intensifier gate time of 350 ns is shown to suppress the detection of phosphorescence signals under practical conditions. An example for a quantitative high-speed measurement of fuel concentration at varying pressure and temperature conditions is presented. Quantitative equivalence ratio maps are shown for the fuel injection event within a single cycle in a spark-ignition direct-injected engine, showing the ability of the technique to not only reveal static fuel concentration maps, but also the motion of the fuel cloud along with very steep gradients. Spray velocities determined from the moving fuel cloud are in agreement with previous particle image velocimetry measurements.     

Hahn-echoes from N in solids by the stray-field method: prospects for imaging using Long Echo-Train Summation

We have observed Hahn-echoes resulting from Powles–Mansfield pulse-sequences for a variety of nitrogen containing solids which exhibit a range of ¹⁴N electric quadrupole coupling constants (C_q) from 0 to 4.9 MHz. Long echo-decays were frequently obtained which allowed the collection of many echoes in one echo-train, so that the method of Long Echo-Train Summation (LETS), could be used to accumulate signal. A one-dimensional STRAFI-profile is shown for solid ammonium nitrate. The spatial resolution is discussed as a function of C_q.