Single‐Mode Microwave Heating‐Induced Concurrent Out‐of‐Plane Twin Growth Suppression and In‐Plane Epitaxial Growth Promotion of b‐Oriented MFI Film under Mild Reaction Conditions

In this study, single‐mode microwave heating was applied in epitaxial growth of b‐oriented MFI seed monolayer prepared by facile manual assembly, resulting in the formation of well‐intergrown and highly b‐oriented MFI film with few twins. It exhibited a precise molecular sieving property at a reaction temperature no higher than 100 °C within 2 hours, therefore making it possible for easy operation in an open environment. The capability for concurrent suppression of undesired out‐of‐plane twin growth and promotion of in‐plane epitaxial growth rate under mild reaction conditions was attributed to the obvious superiority of single‐mode microwave heating in comparison with conventional multi‐mode microwave heating in aspects of microwave field uniformity and intensity. Our research indicated that the single‐mode microwave heating technique could potentially be a useful tool for improving the microstructure and therefore the performance of diverse zeolite films.     

Rapid assessment of the impact of microwave heating coupled with UV-C radiation on the degradation of PAHs from contaminated soil using FTIR and multivariate analysis

The presence and fate of polyaromatic hydrocarbons (PAHs) in the environment are receiving a great concern. In this study, three oil-contaminated soils (industrial area, Dukhan city, and artificial soils) were utilized to examine the effect of microwave (MW) heating and UV-C irradiation on the PAHs degradation. A rapid assessment of the impact was evaluated using Fourier transform infrared (FTIR) and multivariate analysis. The total organic matter values for the maximum PAHs reduction were evaluated based on the FTIR spectra of the contaminated soils followed with the principal component analysis (PCA). The results showed that the highest total organic carbon reduction was achieved for the industrial soil sample that required a high MW power and long MW exposure time. On the other hand, the Dukhan city soil sample, which has the lowest total organic carbon, required a high MW power and short MW exposure time followed by UV-C treatment for 20 min to reach the maximal FTIR transmittance reduction. The cluster analysis was also used to evaluate the impact of MW heating, and MW heating followed by UV-C irradiation on the degradation of PAHs. The PCA results of the industrial city sample showed that neither MW treatment (100% MW, 15 min exposure time) followed by UV-C treatment for 20 min nor 10 min is significantly different from the MW treatment (100% MW, 15 min exposure time). However, for the Dukhan sample, the UV-C treatment at 10 min after high MW power and long exposure time (100% MW, 15 min exposure time) was the most efficient treatment.     

大尺寸电阻加热式碳化硅晶体生长热场设计与优化

大尺寸低缺陷碳化硅(SiC)单晶体是功率器件和射频(RF)器件的重要基础材料,物理气相传输(physical vapor transport, PVT)法是目前生长大尺寸SiC单晶体的主要方法。获得大尺寸高品质晶体的核心是通过调节组分、温度、压力实现气相组分在晶体生长界面均匀定向结晶,同时尽可能减小晶体的热应力。本文对电阻加热式8英寸(1英寸=2.54 cm)碳化硅大尺寸晶体生长系统展开热场设计研究。首先建立描述碳化硅原料受热分解热质输运及其多孔结构演变、系统热输运的物理和数学模型,进而使用数值模拟方法研究加热器位置、加热器功率和辐射孔径对温度分布的影响及其规律,并优化热场结构。数值模拟结果显示,通过优化散热孔形状、保温棉的结构等设计参数,电阻加热式大尺寸晶体生长系统在晶锭厚度变化、多孔介质原料消耗的情况下均能达到较低的晶体横向温度梯度和较高的纵向温度梯度。     

低压供热涂层材料制备及热性能研究

低压供热技术具有安全系数高和节能降耗等优势,因而成为石化稠油长输管线、风力发电叶片冬季防覆冰和室内供暖等领域的研究热点之一。本文制备了一系列低压供热涂层材料,研究不同碳功能填料对涂层发热速率、发热功率及最高发热温度的影响规律,并揭示石墨烯和碳纤维对提升涂层材料热性能的协同作用。其中石墨烯纳米片的还原程度对材料热性能具有重要影响,降低其表面官能团密度对提升涂层供热特性具有促进作用,但是官能团密度过低会导致石墨烯纳米片的团聚现象,引起涂层发热不均匀。加入适量碳纤维可以提高石墨烯的均匀分散性,提升发热速率。优化石墨烯纳米片和碳纤维的比例后,采用24V电压驱动时,涂层材料的发热速率达到7.1℃·s^-1,功率密度为800W·m^-2,最高发热温度为124℃。     

纳米晶型MnCo2O4的微波加热法制备及其电催化性能

以Co和Mn的醋酸盐为原料,采用共沉淀法制得草酸盐前驱物,加入一定量微波吸波剂乙炔黑后,用微波进行热处理制得复合氧化物MnCo2O4.X射线衍射和扫描电镜结果表明,产物为纳米晶型,结晶良好,纯度较高,粒径为10~20nm且分布均匀.在室温下、空气气氛中,以6mol/L的KOH溶液为电解液测试了由MnCo2O4制备的空气扩散电极对氧还原反应的催化效果.极化曲线显示,在-0.2V(vsHg/HgO)电位下,氧还原反应电流密度达96mA/cm2.为显示微波加热法的优越性,用马弗炉煅烧制备了MnCo2O4,并对两种热处理方法所得产物的物化性能进行了比较.     

High-frequency lengthwise diffraction by the curve separating soft and hard part of the surface

The paper examines the model problem of high-frequency diffraction by a convex surface consisting of two parts. One is soft, the other is hard. The incident wave falls at a small angle to the line which separates soft and hard parts of the surface. The change in the boundary condition provokes the field in the Fock zone to have a rapid transverse variation. This causes a special boundary-layer to be formed. The boundary value problem for the three dimensional parabolic equation is reduced to the Riemann problem solved by the factorization in the form of infinite products containing the zeros of the Airy function and zeros of its derivative. the results of this factorization appear under the sign of double Fourier integral in the representation of the field. Both numerical and asymptotic analysis of this representation is carried out and illustrates the effects of high-frequency diffraction caused by the line of the boundary condition discontinuity.     

用于水中有机磷农药检测的离子迁移率谱仪预富集进样方法

建立了检测水中有机磷农药的离子迁移率谱仪预富集进样方法。预富集器由表面覆盖有吸附薄膜的微热板、聚四氟乙烯电路板和管座组成,具有操作简单,无需有机溶剂,自加热,热容小,功耗低等优点。以马拉硫磷检测为例,分析了富集器解吸升温速率和离子迁移率谱仪半透膜温度对检测结果的影响。采用高温短时脉冲加热和低温维持加热相结合的解吸方式,既可形成较高的进样浓度脉冲,又可减少进入漂移管的杂质,有利于提高离子迁移率谱仪检测灵敏度。实验表明:采用所述预富集及两阶段加热解吸进样方法,对水中马拉硫磷的检出限为3.9μg/L,达到了国家标准对水中有机磷检测的要求。     

Evolution of Er^3＋ Distribution in the Oxyfluoride Glass Ceramics with Heating

The distribution characteristics of Er3+ ions doped in the oxyfluoride glass ceramics containing LaF3 nanocrystals heat-treated at 650 ℃ for different durations were investigated. The results of the integral absorption cross-section analysis demonstrated that the partition fraction of Er3+ in LaF3 nanocrystals increases with prolonging of heating time. The anomalous phenomena of Er3+ emissions in the up-and the down-conversion fluorescence spectra are well explained based on the calculated results.     

不同条件对硫酸钙结晶影响的实验研究

近年来由于微波化学的快速发展使人们认识到微波作为一种手段对化学反应的过程有着深刻的影响,在材料领域更是得到了日益广泛的应用,因此把微波应用于结晶过程也成为人们关注的热点。早在1966年磁场就被应用于晶体的生长。近年来,已有很多文献报道电场、磁场对晶体生长的影响。     

MICRO-PHASE SAEPARATION IN EPOXY RESIN WATERBORNE PARTICLES DURING CURING PROCESS

Sub-micron sized phenolic epoxy resin waterborne particles were prepared by phase inversion emulsification. Micro-phase separation occurred during the curing process at high temperature. The as-prepared samples possessed one glass transition temperature （Tg） and two exothermal processes during DSC heating scannings. After being thermally treated above the exothermal peak temperature, they possessed two glass transition temperatures with the disappearance of exothermal peaks, whilst a core/shell structure was formed. This was likely related with the outward diffusion of reactive oligomers to the outer layer of particles.