Au deposits on graphite: On the nature of high temperature desorption peaks in CO thermal desorption spectra

Due to the discovery of Au as a catalyst for low temperature CO oxidation, the adsorption of CO on Au surfaces has attracted a lot of attention recently. On stepped and rough single crystal surfaces as well as on deposited particles two characteristic desorption states above 100 K have been observed via TPD. We have studied Au deposits on graphite in order to elucidate the nature of these desorption peaks in more detail. For this purpose, Au was deposited at 100 K and 300 K on HOPG as a weakly interacting support. In analogy to other supports, we obtain two desorption states (∼140 K and ∼170 K) whose relative intensities depend strongly on the deposition temperature with the high temperature peak being much more pronounced for the 100 K deposits. After annealing to 600 K, both states drastically lose intensity. XP spectra, on the other hand, show virtually no decrease of the Au 4f intensity as would be expected for desorption or significant changes of the particle morphologies. We conclude that both desorption peaks are defect-related and connected with under-coordinated Au atoms that are lost for the most part upon annealing. These sites could be located at the perimeter of dendritic islands or on small, defect-rich particles in addition to larger particles not adsorbing CO at 100 K. Preliminary STM results are in favour of the second interpretation.     

WLY100型顺序扫描ICP光谱仪设计方案的一些考虑

本文对国产ＷＬＹ１００型顺序扫描ＩＣＰ光谱仪在设计中对单色仪，高频发生器，扫描机构，测光系统，短紫外光域的测量，恒温，气流控制与软件编制等方案的选择作了详尽的阐述，稳妥的方案使研制工作顺利进行，保证整机一次成功。     

加热炉热过程动态操作数学模型

根据加热炉生产特点,建立了钢坯加热过程的动态操作数学模型,分析了待轧时间变化时炉内钢坯温度分布情况。并针对加热炉待轧的灰色性,采用多目标灰色局势决策方法,得出了相应合理的待轧优化控制策略。模拟结果表明:该方法具有良好的动态性能,适合于在线控制。     

溶膜预富集-石墨炉原子吸收法测定痕量钯

强酸性条件下 ,钯 (Ⅱ )与 5 [( 5 氯 2 吡啶 )偶氮 ] 2 ,4 二氨基甲苯 ( 5 Cl PADAT)生成紫红色螯合物 ,该螯合物可与十二烷基苯磺酸钠 (SDBS)生成离子缔合物 ,离子缔合物经 0 .3μm孔径的硝化纤维微孔滤膜富集后 ,于小体积 ( 0 .5mL)的浓硫酸中溶膜 ,用石墨炉原子吸收法 (GFAAS)测定 ,富集倍数可达 2 0 0倍 ,钯含量在 4.69× 1 0 - 1 2 ～ 7.0 9× 1 0 - 9mol/L范围内线性良好 ,检出限为 1 .78×1 0 - 1 2 mol/L。方法用于海水中痕量钯的测定。     

Thermal Analysis in Examination of Reduction of Blast Furnace Pellets

This paper presents applications of thermal analysis to observe the course of reduction of acidic pellets, metallurgical substances whose reducibility and strength are basic parameters of use in blast furnace processes. Both parameters depend on the mineral composition of the samples. The investigations included determination of the chemical and phase compositions of the initial samples and reduction products. Research was conducted on acidic pellets from Połtawa (Poland), applied in the T. Sendzimir Steelworks (Poland), in comparison with pellets from Brazil, Canada and Lebedyn (Russia). This revised version was published online in August 2006 with corrections to the Cover Date.     

Influence of boric acid on the electrochemical deposition of Ni

The electrolytic deposition of Ni onto a paraffin-impregnated graphite electrode from supporting chloride electrolyte (0.5 mol dm⁻³ NaCl) adjusted to the required pH using dilute HCl is investigated. The effect of electrolyte composition on the Ni electrodeposition is studied using linear sweep voltammetry in the cathodic region. An elimination voltammetry procedure was applied to evaluate the polarization curves. The aim of this work was to deduce the mechanism of Ni reduction in the chloride bath as well as the influence of boric acid on this. Positively-charged NiCl⁺ ions were found to be the electroactive particles in the Ni reduction mechanism. The strong competition between the NiCl⁺, Cl⁻ and H⁺ ions for active sites at the electrode is discussed. Kinetically-controlled adsorption/desorption processes of various species were also confirmed using elimination voltammetry with a linear scan. The evolution of gaseous hydrogen, catalyzed by the freshly-deposited Ni, accompanies the electrodeposition process. The presence of boric acid at a sufficiently high concentration inhibits the deposition of Ni and, at the same time, improves the morphology and brightness, as well as the adhesion of the deposited Ni. Elimination voltammetry with a linear scan is an efficient way to evaluate current–potential curves that reflect the electrodeposition of one-component Ni coatings. By eliminating selected currents, additional interesting and useful information can be obtained from voltammetric data.     

A study of the polymerization of styrene initiated by K-THF-GIC system

In this paper, the polymerization of styrene initiated by potassium (K)-tetrahydrofuran (THF)-graphite intercalation compound (GIC) (K-THF-GIC) was studied. The mechanism of the polymerization was determined to be anionic polymerization according to its characteristics. The effect of the concentration of the initiator and monomer was studied. It was found that the polymerization mainly occurred on the surface and edge of the intercalated graphite. It was also shown that the polarity of solvent has little effect on the polymerization yield in this system.     

衬钽管石墨炉中小量氢气的影响及稀土基质激光晶体中铕的测定

通过纯氩中加入小量氢气,研究了保护气体对衬鉏管石墨炉分析性能的影响,结果表明,采用5％H_2-Ar作保护气体,可以显著提离衬鉏管的成品率,明显延长衬鉏管的使用寿命,使衬钽管的测定重现性得到改善,而对测定灵敏度没有明显影响。干扰试验表明,本方法可直接用于稀土基质激光晶体中铕的测定,分析结果与计算值基本一致。     

衬钽管石墨炉原子吸收法测定痕量镓时基体改进剂的研究及应用

提出用钒和铜混合基体改进剂衬钽管石墨炉原子吸收测定镓的方法。衬钽管使镓的灵敏度提高6倍左右,钒和铜混合基体改进剂不仅能进一步提高灵敏度,而且能提高灰化温度,降低原子化温度,增强抗干扰能力。测定 GSD 标准样品中的镓时,不需对样品进行预分离即可直接进行测定,结果与参考值相符。     

Feasibility of using solid sampling graphite furnace atomic absorption spectrometry for speciation analysis of volatile and non-volatile compounds of nickel and vanadium in crude oil

A method for the direct determination of volatile and non-volatile nickel and vanadium compounds in crude oil without previous treatment using direct solid sampling graphite furnace atomic absorption spectrometry is proposed. The crude oil samples were weighed directly onto solid sampling platforms using a microbalance and introduced into a transversely heated solid sampling graphite tube. In previous work of our group losses of volatile nickel and vanadium compounds have been detected, whereas other nickel and vanadium compounds were thermally stable up to 1300 and 1600 °C, respectively. In order to avoid this problem different chemical modifiers (conventional and permanent) have been investigated. With 400 μg of iridium as permanent modifier, the signal started to drop already after two atomization cycles, possibly because of an interaction of nickel (which is a catalyst poison) with iridium. Twenty micrograms of palladium applied in each determination was found to be optimum for both elements. The palladium was deposited on the platform and submitted to a drying step at 150 °C for 75 s. After that the sample was added onto the platform and submitted to the furnace program. The influence of sample mass on the linearity of the response and on potential measurement errors was also investigated using four samples with different nickel content. For the sample with the lowest nickel concentration the relationship between mass and integrated absorbance was found to be non-linear when a high sample mass was introduced. It was suspected that the modifier had not covered the entire platform surface, which resulted in analyte losses. This problem could be avoided by using 40 μL of 0.5 g L⁻¹ Pd with 0.05% Triton X-100. Calibration curves were established with and without modifier, with aqueous standards, oil-in-water emulsions and the certified reference material NIST SRM 1634c (trace metals in residual fuel oil). The sensitivity for aqueous standards and emulsions was close to that for SRM 1634c, making possible the use of aqueous standards for calibration. The limits of detection and quantification obtained for nickel and vanadium under this condition were found to be 0.02 and 0.06 μg g⁻¹, respectively, for both elements, based on 10 mg of sample. Nickel and vanadium were determined in the samples with (total Ni and V) and without the use of Pd (thermally stable compounds), and the concentration of volatile compounds was calculated by difference. The results were compared with those obtained by high-resolution continuum source graphite furnace atomic absorption spectrometry by emulsion technique; no significant differences were found for total Ni and V at the 95% confidence level according to a Student's t-test.