HFP—2500F高频发生器故障诊断与维修

本文介绍了高频发生器在日常工作中经常出现的故障，以及诊断排除方法。     

Er3+掺杂ZBLAN非晶的激发态频率上转换

非晶ZBLAN光纤玻璃中掺杂稀土离子Er³⁺的上转换发光的研究表明,在室温、大功率半导体激光器的激发下,Er³⁺的荧光主要是通过单离子步进双光子过程发生的,而其多光子过程虽然非常微弱,但在强的半导体激光的照射下也可产生.通过对这两种不同过程的实验测量,可以为进一步深入地研究上转换机制提供新的依据.     

Structure and polarity of 8CB films evaporated onto solid substrates

Brewster-angle reflection ellipsometry and surface optical second harmonic generation were used to study the growth of 4'-n-octyl-4-cyanobiphenyl (8CB) films evaporated in air onto polymeric and quartz glass substrates. The layer-by-layer growth of the films terminates after formation of two distinctive interfacial layers. Both of these two layers are polar and tilted. In the first layer the molecules lie nearly flat on the surface, while in the second layer they point on average about 50° toward the surface normal. The dipole moment of the second layer has a lower magnitude and an opposite direction with respect to the dipole moment of the first layer.     

基于PML边界的有限差分法及其在光波导泄漏损耗计算中的应用

利用结合完美匹配层(PML)边界的有限差分法计算了光波导的泄漏损耗.通过采用非均匀格点差分格式和反正切坐标变换的方法,有效地减小了计算量并提高了计算精度.分析了PI(polyimide)掩埋型波导和SOI(silicon-on-insulator)脊型波导两种典型结构的泄漏损耗,给出了波导结构尺寸对泄漏损耗的影响,并对有效减小泄漏损耗的方法进行了讨论.     

光纤陀螺数字闭环控制系统模型实验研究

数字闭环光纤陀螺的动态性能受控制系统设计的影响.根据光纤陀螺数字闭环检测过程,建立了控制系统的数学模型.为在全频带内对模型进行验证,提出了基于Faraday效应的光纤陀螺频率响应测试方法,对该测试方法与角振动台测试方法的等效性进行了分析.设计了频率响应测试系统,测试范围大于50 kHz,波形失真小于0.1%.实测了采用一阶积分控制算法的数字闭环光纤陀螺频率响应.实验结果表明模型误差小于8%.     

A Millimeter Wave Phase Locked and Frequency Multiplying Source

A millimeter wave phase locked and frequency multiplying source is proposed in this paper. The design includes an X-band phase locked loop (PLL) frequency synthesizer as the base frequency source, and a monolithic millimeter wave frequency tripler, which is developed by using OMMIC 0.18μm pHEMT process. The PLL and the tripler are integrated in a single circuit board to make a low-cost and compact frequency source with the size of 6cm × 5cm. Measurement shows an output power of more than 4.8dBm at the frequency range from 35 to 36.7GHz. A phase noise of about -92dBc/Hz at 100kHz offset is achieved.     

Fill factor controlled nanoimprinted ZnO nanowires based on atomic layer deposition

Enhanced diffraction by sub-wavelength nanostructures to convert incident electromagnetic radiation into waveguide modes has applications in anti-reflective coatings for optoelectronic devices. We propose a metal oxide (ZnO) nanowire grid polarizer as such a nanostructure, fabricated by ultraviolet nanoimprint lithography and whose fill factor (FF) is controlled by atomic layer deposition. Using finite difference time domain simulations, we investigated the polarization-dependent optical transmittance of the structures and calculated the polarizing efficiency. Optical profiles such as electric and magnetic field intensity and current density distributions of specific FF nanopatterns were determined for the transverse magnetic and transverse electric modes. The effects of geometrical parameters including the wire-grid period, fill ratio, and spacing between the wire-grid layers on diffraction wavelength were characterized. Respective FF-controlled ZnO nanowire structures were fabricated and their experimental optical transmittances were measured for nanowire grid polarizer applications.     

A numerical model of multimode fiber PON frequency response

Frequency response of passive optical network (PON) based on multimode fibers is investigated. The network comprises fibers, connectors and splitters/couplers. It is shown that due to mode filtering at splitters, the frequency response is different for different network nodes in otherwise symmetrical network.     

Phase-matched third-harmonic UV generation using low-order modes in a glass micro-fiber

We observe phase-matched third-harmonic generation at 355 nm in a low-order mode of a sub-micron diameter glass fiber. The third-harmonic signal exhibits a sharp resonance for a fiber diameter d = 0.49 ± 0.02 μm, in excellent agreement with the value d = 0.506 μm predicted by theory. The third-harmonic conversion efficiency is 2 × 10⁻⁶, and is limited by the pump power (1 kW) and effective fiber length (100 μm).     

非结构网格上温度扩散方程的能流计算方法

讨论非结构网格上温度扩散方程的能流计算方法.应用有限点方法(Finite Point Method,简称FPM)导出基于有限点两点公式和三点公式的能流计算公式,该公式适用于任意多边形及非匹配网格等非结构网格;给出网格角点温度新的计算公式.数值试验表明:基于两点公式的离散解和基于三点公式的离散解均具有平方阶的收敛速度;基于三点公式的离散解的精度总优于基于两点公式的离散解.