火焰辐射及偶丝导热对热电偶测温影响的数值分析

本文利用层流同向扩散乙烯火焰的数值模拟结果,根据所得的火焰温度场、气体速度场、火焰辐射场,分析火焰辐射、热电偶偶丝导热对热电偶测温的影响.结果表明在火焰的低温区火焰辐射要大于节点向外辐射,节点得到的能量要高于节点损失的能量,因此在火焰的低温区节点温度要高于当地的气体温度;同时直径为100μm的热电偶存在较大的导热,对节点温度测量有较大的影响.     

Electron–phonon effect on the ground-state binding energy of hydrogenic impurity in quantum-well wire in presence of an electric field

The hydrogenic impurity binding energy in rectangular quantum well wire including both barriers of finite height and an applied electric field are studied. The polaron effects on the ground-state binding energy in electric field are investigated by means of Landau-Pekar variation technique. The results for the binding energy as well as polaronic correction are obtained as a function of the size of the wire, the applied electric field and the position of the impurity. Our calculations are compared with previous results in quantum wires of comparable dimensions.     

An investigation into EMI-induced noise in nanometer multi-quantum well InGaN LEDs

This study investigates the low-frequency noise induced by electromagnetic radiation interference (EMI) in a nanometer multi-quantum well InGaN LED (NMQLED). Theoretical models of the noise spectra and the EMI are constructed. In general, a good agreement is identified between the experimental and theoretical results. Both sets of results reveal that the magnitude of the EMI-induced noise is related to the pulse height, the output load, the parasitic capacitance, the interference frequency and the interference amplitude. It is shown that the harmonic noise increases with an increasing interference amplitude and frequency. The techniques presented in this study provide a systematic approach for obtaining the interference noise and signal-to-noise ratio (SNR) in LEDs and similar wavelength-based semiconductor devices.     

两相颗粒多孔材料导热系数研究

对固-气两相颗粒多孔材料导热系数的预测,尚未见以实验数据对其各预测模型进行分析及验证其准确度的相关文献。本文利用断电热线法测定石英砂、碳化硅、工程沙以及煤灰的导热系数;将模型预测结果与实验数据进行对比分析,结果表明,Kunii and Smith模型误差小;考虑孔隙率的影响,利用实测数据对Kunii and Smith模型进行修正,给出新的预测模型;通过与国外学者给出的实测导热系数的对比,验证了本文给出的修正模型的准确性。     

钢丝绳模型比较研究

将现有的各种钢丝绳计算模型进行比较研究，通过将数值结果与现有的实验数据进行比较可以看出，考虑绳芯变化并结合Love曲杆理论的JW和KC模型更适用于实际的钢丝绳结构。     

Analysis of temperature and stress field in Al alloy’s twin wire welding

By analyzing the shape of twin wire welding’s arcs and the track of droplets’ transition, the phenomenon that the twin wire welding’s fore arc and rear arc all deflect to the middle of the two arcs is found. Based on this the double ellipsoid heat source model is amended, and a heat source model which can apply to calculate the twin wire welding’s temperature field is put forward. This model is testified by actual experiment of temperature sampling. By comparing the temperature field of twin wire welding and single wire welding, the results show that twin wire welding has slender weld pool the end part of which is ellipsoid, and its HAZ is narrower than that of single wire welding. So, twin wire welding can not only reduce the Al alloy generating hot crack, but can also weaken the “overaging” softened phenomenon of heat treated strengthening Al alloy. In the end, the evolving rules of 2219 Al alloy’s longitudinal and transverse stress when welded with twin wire welding are analyzed.     

Au nanoparticles as a novel coating for solid-phase microextraction

A novel solid-phase microextraction fiber based on a stainless steel wire coated with Au nanoparticles was prepared and has been applied, coupled with gas chromatography, to the extraction of aromatic hydrophobic organic chemical pollutants in rainwater and soil extract. The solid-phase microextraction fiber exhibited excellent extraction efficiency and selectivity. Effects of extraction time, extraction temperature, ionic strength, stirring rate and desorption conditions were investigated and optimized. Single fiber repeatability and fiber-to-fiber reproducibility were less than 7.90% and 26.40%, respectively. The calibration curves were linear in a wide range for all analytes. Correlation coefficients ranged from 0.9941 to 0.9993. The as-established SPME-GC method was used successfully to two real natural samples. Recovery of analytes spiked at 10 μg L(-1) and 100 μg L(-1) ranged from 78.4% to 119.9% and the relative standard deviations were less than 11.3%.     

Z箍缩丝阵负载区域的似稳态磁场分布

 将负载区域的电流（丝阵电流、阴极板电流、阳极板电流和回流柱电流）离散成电流线或电流面等电流微元,根据毕奥-萨伐尔定律,计算所有电流微元在指定场点的磁场,再通过叠加给出该点的总磁场。研究结果发现:在丝阵外围区域,仅由丝阵电流所产生的磁场偏离无限长直导线磁场公式的值,但全部电流所产生的总磁场与公式给出的值很接近。同时,研究了不同负载结构参数下的磁场分布,结果表明：增加丝根数有助于减小单根丝表面的局部磁场,改善丝阵外围磁场分布的均匀性。     

Abrasive resistance of arc sprayed carbonitride alloying self-shielded coatings

Wear-resistant coatings were prepared on the surface of the Q235 low-carbon steel plate by HVAS with the carbonitride alloying self-shielded flux-cored wire. Detection and analysis on the microstructure and properties of the coatings were carried out by using scanning electron microscope, microhardness tester and wear tester. The forming, the wear resistance and its mechanism of the coatings were studied. The results show that the coatings have good forming, homogeneous microstructure and compact structure. The coatings have good hardness, the average microhardness value reaches 520 HV_0.1, and the highest value is up to about 560 HV_0.1. As a result, the coatings have good abrasive wear performance and adhesion strength.     

Ce-Pt-Pd/不锈钢丝网催化剂的制备与催化性能

采用阳极氧化技术在不锈钢丝网上自生长了一层结构致密的阳极氧化膜,并以此为载体,制备出一种高活性、高稳定性的负载型Ce-Pt-Pd催化剂.考察了该系列催化剂对甲苯、丙酮和乙酸乙酯的氧化活性,并用扫描电镜、X射线光电子能谱和程序升温氧化技术对催化剂进行了表征.结果表明,不锈钢丝网载体表面自生长的氧化物膜十分有利于活性组分的负载,制得的催化剂具有较高的催化燃烧有机化合物的活性和稳定性.