Determination of chloride ion in aqueous samples by isotope-dilution Fourier-transform flame infrared emission (ID-FIRE) spectrometry

An isotope dilution method for the determination of chloride ion in aqueous samples is described. The method makes use of the isotopic shift in the rotational lines of the 1–0 band of HCl emitted in the near infrared region of the spectrum by vibrationally excited HCl molecules present in a hydrogen/entrained air flame. Chloride ion in the sample is converted to chlorine gas by electrolysis and swept into a hydrogen/entrained air flame where it is converted into HCl. Because isotope dilution is an absolute method of analysis, matrix effects are minimized, and the chlorine generation step need not be quantitative. With the system described in this paper, samples must contain at least 9 mg of chloride ion per ml, and a 2-ml sample is required. Over the range from 10 to 30 mg Cl⁻ ml⁻¹, the average error was −0.96%, and the average relative standard deviation was 3.3% for seven samples using seven of the more intense lines in the P branch. Compared with standard silver nitrate titrations, the isotope dilution procedure was not affected by such common interferences as bromide ion and iodide ion. The technique was applied to several seawater samples from different regions.     

Determination of copper in medicinal plants used as dietary supplements by atomic absorption spectrometry with direct flame solid analysis

An alternative device for the direct solid analysis (DSA) for copper determination by flame atomic absorption spectrometry (FAAS) is proposed. Copper was directly determined in commercial medicinal plants used as dietary supplements. The determination of copper in solid samples by DSA–FAAS was made by using a conventional air–acetylene flame. Between 0.05 and 1.5 mg of each test, sample was weighed directly into a small polyethylene vial connected to the device used for solid introduction into the flame. Test samples were introduced into the flame as a dry aerosol using a T-quartz cell set between the burner and the optical path. The T-quartz cell has a slit in the superior part by which the solid aerosol passes to the flame. A transient signal, evaluated as integrated absorbance, is produced and it is totally integrated in 2 s. Background signals always presented absorbance values less than 0.1. It was found a characteristic mass of 0.8 ng Cu and absolute limit of detection of 1.2 ng (3 s), or 1.2 μg g⁻¹ if a sample mass of 1 mg was used. Optimized conditions for air flow rate, flame stoichiometry, and so on were established as well. No excessive grinding of the samples was needed and samples with particle of size less than 80 μm were used throughout. No statistical difference between the results from the proposed system and those obtained by sample digestion and determination by conventional FAAS was observed. With the proposed procedure, more than 50 test samples can be analyzed in 1 h and it can be easily adapted to conventional spectrometers for FAAS.     

Scratch and Abrasion Resistant Coatings on Plastic Lenses—State of the Art,Current Developments and Perspectives

The manufacturing of ophthalmic lenses is one of the most important markets worldwide and, therefore, strong research efforts are undertaken to continuously improve the quality of the products, either silicate glasses or organic polymer lenses. Hybrid sol-gel based materials play a major role in this highly competitive field and have contributed significantly to the commercial success of the organic base materials. Recent developments concern fast curing and patternable coatings that might soon become part of this business. The compatibility of hybrid sol-gel materials either with organic dyes or with inorganic vacuum borne coatings offers further possibilities to develop highly sophisticated lenses meeting not only customer needs like perfect corrective function, high optical quality and protection, but also high durability as well as cosmetic and decorative aspects. An overview and a few recent developments are outlined below.     

Validation of an analytical method to determine trace metal impurities in fluoride compounds by flame atomic absorption spectroscopy

 The development of an analytical method for the determination of some heavy metals (Fe, Cu, Co, Zn and Ni) in fluoride compounds [Cu(BF₄)₂, Sn(BF₄)₂, Pb(BF₄)₂ and HBF₄] by flame atomic absorption spectroscopy is described. This method is to be used as a routine analytical method in an industrial quality control laboratory. To this end the "performance characteristics" of an instrumental analytical method such as matrix effects, sensitivity, linearity, detection and quantitation limits, precision and accuracy were evaluated for every system under study. The results of these investigations showed that non-spectral interferences (due to the presence of large concentrations of major metals such as Cu, Sn and Pb) were observed. Nevertheless it was possible to define a matrix concentration interval where matrix effects were not statistically significant, and therefore a direct calibration approach could be used as the calibration tool whenever the major metal concentration was not higher than 40×10^–3 kg l^–1. A guide to the developement of an analytical method for trace metal determination is provided. General tools for quality control have been used in order to show how an analytical method can be tested daily and evaluated in a convenient manner. Received: 29 January 1997 Accepted: 11 March 1997     

Cu-P系稀土耐候钢中最佳稀土含量的研究

利用光学显微镜、图像分析仪和电子探针对低氧低硫的10PCuRE耐候钢板坯进行了观察和检测,采用干-湿周浸室内加速试验方法测得了试验钢的腐蚀率.用电化学方法测得了带锈样的阳极极化曲线.研究得出对于S:～0.004%,O:～0.002%的10PCuRE耐候钢,最佳稀土含量为0.0065%～0.012%,此稀土含量对非金属夹杂物的变质作用和耐蚀性能的提高最为有利.     

Dissolution of copper foil in aqueous solution ofpH=2

The specific dissolution rate, expressed in mol cm^–2s^–1, and time-variation of the rest potential of copper foil in an aerated aqueous solution ofpH = 2.0 were measured.

---

Die Auflösbarkeit von Kupfer-Folie in wäriger Lösung von pH 2 (Kurze Mitteilung)

Zusammenfassung Es wurde die spezifische Auflösungsgeschwindigkeit (in mol cm^–2s^–1) und die zeitliche Veränderung des Restpotentials von Kupfer-Folie in einer belüfteten wäßrigen Lösung von pH 2,0 gemessen.

     

Evaluation of digestion procedures for the determination of iron and zinc in biscuits by flame atomic absorption spectrometry

An evaluation is made of different digestion methods for the determination of iron and zinc in biscuits prior to flame atomic absorption analysis. For the initial studies, microwave digestion was enough (using hydrogen chloride and nitric acid 3:1, v/v, at 180 °C and 600 W) to provide comparable accuracy, precision, digestion time and non-critical handling of reagents to dry-ashing and wet digestion (using different acid mixtures) and also to a simple acid treatment at room temperature. Although, after a simple microwave digestion, the spiked recoveries were found around 96–102%, to reduce the digestion time and for simplicity we worked on wet acid treatments. The results showed that acid-only treatment is not enough to digest the samples without adding ethanol, which was found necessary to digest organic residue at room temperature. The method was validated by comparison of the data found for commercial biscuit samples through using the proposed procedure and the AOAC official reference spectrophotometric method. Fe concentration in the different biscuits (such as petit beurre, baby biscuits, etc.) ranged from 1.21 to 15.96 mg/100 g while Zn concentration ranged from 0.58 to 2.50 mg/100 g depending on biscuit type. The highest concentration of Fe was in baby biscuits and these biscuits were about thirteen times richer in Fe than petit beurre biscuits.     

Melamine cyanurate-microencapsulated red phosphorus flame retardant unreinforced and glass fiber reinforced polyamide 66

A novel microencapsulated red phosphorus (RP) was prepared through the molecular self-assembly of melamine cyanurate (MCA). Compared with the conventional encapsulated RP, MCA-encapsulated RP (MERP) shows simpler and more environment-friendly preparation process higher thermal stability and lower moisture absorption. With MERP filled in unreinforced polyamide 66 (PA66) and glass fiber (GF) reinforced PA66, flame retardant materials with satisfactory flame retardancy and mechanical performance can be obtained. The influence of the MCA/RP ratio on the flame retardancy as well as the condensed phase of MERP flame retardant PA66 was investigated to reveal the nitrogen-phosphorus (N-P) synergistic flame retarding effects between MCA and RP.     

分析信号处理方法的比较研究

研究了高效液相色谱－火焰原子吸收光谱联用系统分析信号处理方法，比较了各种处理方法的优缺点，用积分与适应平滑法综合处理色谱峰分析信号，不仅能有效地消除噪声，而且能使分析信号得到加强，以测定镍为例，经积分与适应平滑法综合处理后，检出限改善了２．７倍。     

Influence of Some Aggressive Media on Corrosion Resistance of Mortars With Spent Cracking Catalyst

The influence of spent catalyst from catalytic cracking in fluidized bed on the hydration process of cement and the properties of cement mortars were studied. The spent catalyst was used as an additive to cement in the mortars (10 and 20% of cement). The samples of mortars kept in water for28 days, then they were placed in sulfate and chloride media for 2 months (the control samples were kept in water for 3 months). After this time they were subjected to bending strength and compressive strength determinations. Thermogravimetric and infrared absorption studies were performed and capillary elevation, capability of binding heavy metals, and changes in mass and apparent density were determined too. The studies disclosed the pozzolana nature of spent catalyst and its influence on cement mortars being in contact with corrosive media. This revised version was published online in August 2006 with corrections to the Cover Date.