Integrated optical cross strip polarizer concept

Passing across an abrupt junction from a thick vertically bimodal waveguide to a thinner single mode segment, guided light can undergo complete destructive interference, provided that the geometry and the phases of the modes in the initial segment are properly adjusted. We propose to employ this effect to realize a simple polarizer configuration, using a strip that is etched from a planar waveguide. A beam of light is made to pass the strip perpendicularly. The light enters from the single mode waveguide outside the strip into the strip segment, which is configured to support two modes. At the end of the strip, apart from reflections, the amount of power that is guided in the following lower segment depends on the local phases of the two modes. These phases are different for TE and TM light, hence we may expect a polarization dependent power transfer, resulting in polarizer performance for a properly selected geometry. The paper describes in detail the modeling of the device in terms of rigorous mode expansion. Design guidelines and tolerance requirements for geometric and material parameters are discussed. For typical Si₃N₄/SiO₂ materials, our calculations predict a peak performance of 34 dB polarization discrimination and 0.3 dB insertion loss for a device with a total length of about 12 m that selects TE polarization at a wavelength of 1.3 m.     

The PMD of sinusoidally spun fibers in the presence of random birefringence perturbations

Although fiber spinning is known to reduce polarization mode dispersion (PMD) effects in optical fibers, relatively few studies have been performed of the dependence of the reduction factor on the strength of random birefringence fluctuations. In this paper, we apply a general mathematical model of random fiber birefringence to sinusoidally spun fibers. We find that while even in the presence of random birefringence perturbations the maximum reduction of PMD is still obtained when the phase matching condition is satisfied, the degree of PMD reduction and the probability distribution function of the DGD both vary with the random birefringence profiles.     

光纤陀螺数字闭环控制系统模型实验研究

数字闭环光纤陀螺的动态性能受控制系统设计的影响.根据光纤陀螺数字闭环检测过程,建立了控制系统的数学模型.为在全频带内对模型进行验证,提出了基于Faraday效应的光纤陀螺频率响应测试方法,对该测试方法与角振动台测试方法的等效性进行了分析.设计了频率响应测试系统,测试范围大于50 kHz,波形失真小于0.1%.实测了采用一阶积分控制算法的数字闭环光纤陀螺频率响应.实验结果表明模型误差小于8%.     

利用迈克耳孙干涉仪重建蜡烛火焰温度场

利用教学实验中的迈克耳孙干涉仪,进行蜡烛火焰温度场的测量.对干涉条纹进行了处理和细化,并分别用阿贝尔变换法和环带法对蜡烛火焰的温度场进行了计算,得到蜡烛火焰横截面上温度场的定量结果.     

Stable multiwavelength and passively mode-locked Yb-doped fiber laser based on nonlinear polarization rotation

Based on the nonlinear polarization rotation (NPR) technique and a fiber Mach–Zehnder interferometer (MZI), a fiber laser which can work in two different modes has been demonstrated. In one mode, it works as a continuous wave (CW) multiwavelength laser, and stable dual-, triple- and tetra-wavelength lasing with the wavelength spacing of 1.1 nm are obtained. In the other mode, it works as a passively mode-locked fiber laser, and the generated pulses have a repetition rate of 10.6 MHz, an FWHM width of 800 ps and the largest energy of 1 nJ. The multi-functional property makes this fiber laser a very convenient, cost effective and multi-purpose laser source.     

全光纤激光相干合成光谱响应特性研究

基于N-腔镜谐振腔理论对全光纤激光相干合成进行了理论分析，数值模拟了迈克尔逊型相干合成激光器的光谱特性，对两个光纤Bragg光栅的中心波长差和两路光的光程差对合成光谱特性的影响给出了理论解释.用啁啾光纤光栅取代其中一个光纤Bragg光栅，使激光相干合成的带宽由0.3 nm拓展到1.0 nm.     

A Method for Measuring the Three-Dimensional Refractive-Index Distribution of Single Cells Using Proximal Two-Beam Optical Tweezers and a Phase-Shifting Mach—Zehnder Interferometer

This paper describes a method for measuring the three-dimensional (3D) refractive-index distribution in a single cell. The method can be used to observe the distribution of cell components without fluorescence staining. The two-dimensional optical path length distributions from multiple directions are obtained by non-contact rotation of the cell. These optical path lengths are converted into the line integrals of the refractive index, and the 3D refractive-index distribution is reconstructed by means of computed tomography. The refractive-index distribution in a breast cancer cell can be measured using a phase-shifting Mach—Zehnder interferometer in conjunction with proximal two-beam optical tweezers.     

The influence of fiber dispersion on the code form of the optical mm-wave signal generated by single sideband intensity-modulation

We have theoretically investigated the transmission performance of the optical mm-wave generation by using an external modulator based on single sideband (SSB) intensity modulation. Though the SSB millimeter (mm)-wave can immune the fading effect, the baseband signals with a high bit rate are degraded greatly after transmission along fiber. The main reason is that the fiber dispersion causes the time shift of the code edges; therefore the maximum transmission distance of the baseband signals is limited. The experimental and simulation results agree well with our theoretical analysis. We also propose a novel scheme to extend the transmission distance. In this novel scheme, the data signals are modulated only onto one of the two optical carriers; hence the shift of the code edges in the down-converted signals after transmission is eliminated.     

Angular interferometer using calcite prism and rotating analyzer

An interferometer using a calcite prism and rotating analyzer is proposed for angular displacement determinations. The calcite prism senses the angular displacements and the rotating analyzer transfers the interference signals from dc-type into ac-type. Compact optical setup and using low-cost devices are thus the advantages of the interferometer. The theory of the interferometer is first demonstrated. A setup constructed to realize the interferometer and the results of using this setup are then presented.     

A cheap and practical FBG temperature sensor utilizing a long-period grating in a photonic crystal fiber

A whole temperature sensor in one package utilizing a fiber Bragg grating (FBG) made in a conventional single-mode fiber and which uses a long-period grating (LPG) made in a photonic crystal fiber is proposed and experimentally demonstrated. The function of the interrogation is that the wavelength change of the FBG with environmental temperature is transferred to the intensity of the output via the LPG. Utilizing the temperature-insensitivity of the LPG in the PCF, the interrogation is stable and enables a cheap and practical temperature measurement system with a wide dynamic range.