Survivability in IP-over-WDM Networks: WDM Lightpath Protection versus IP LSP Protection

This article compares the performance of WDM lightpath protection and IP LSP protection schemes for IP-over-WDM networks. A mathematical formulation of the maximum throughput problem is presented and analytical expressions for recovery time are derived for both schemes. The throughputs and recovery times are analyzed and compared. Results show that the IP LSP protection scheme presents higher throughputs then WDM lightpath protection. The IP LSP protection scheme, providing individual IP LSP protection has, however, scalability problems. This scheme presents high recovery times when a failure affects many lightpaths and many hops are allowed for the primary routes of IP LSPs.     

机载海洋激光测深系统参量设计与最大探测深度能力分析

详细讨论了机载海洋激光测深系统最大测量深度与相关因子之间的关系，并利用最小可探测信噪比为判据，对机载海洋激光测深系统在白天和晚上工作进行了数值模拟，通过比较最大测量深度与激光脉冲峰值功率、接收视场角、接收口径和光谱接收带宽等关系，确定了系统的主要参量。以确定的参量建立的系统具有白天49m和晚上65m的最大测深能力，可完全满足在沿岸带以及岛礁的测量要求。     

滤波器对偏振模色散的补偿

根据耦合非线性薛定谔方程 ,本文研究了偏振模色散如何影响各种码型的频谱 ,分析了滑频滤波器和固定滤波器对偏振模色散的补偿作用。研究结果表明 :偏振模色散对不同码型的频谱影响是不一样的 ,对色散管理孤子的频谱影响最大 ,产生新的频率分量也最多 ,而且每个新频率分量都较强 ,比入射频谱展宽许多 ;滑频滤波器和固定滤波器对偏振模色散都具有补偿作用 ,使最大可传输距离成倍增加 ,两种滤波器对偏振模色散的补偿作用相差较小 ;但是对色散管理孤子系统中的偏振模色散补偿效果最佳。     

Photorefractive Four-Wave Mixing Switches Utilizing Pockels Effect -Longitudinal and Lateral Switches-

We carried out detailed calculations for photorefractive wave-mixing switches based on one of three crystals with high electro-optic coefficients, namely, BaTiO₃, Strontium Barium Niobate (SBN (0.75)), and Potasium Sodium Strontium Barium Niobate (KNSBN). A comparison of results for the three crystals shows that a 0_-cut BaTiO³ crystal is suitable for a longitudinal switch and requires a voltage of about 80 for a 2-mm-thick crystal to induce sufficient phase mismatch. The electrodes must be transparent for the incident and diffracted beams. A 45_-cut SBN (0.75) crystal, however, is suitable for a lateral switch and requires a voltage of about 150 for a 1-mm-wide crystal. The electrodes do not need to be transparent.     

Measurements of Time-Varying Characteristics of Optical Signals and Inhomogeneities of Tested Substances with Additional Phase Modulation

The problem of investigation of the amplitude and phase structure of a time-varying probing optical signal and the structure of time-varying inhomogeneities of a substance tested by this signal is considered. The analysis is concerned, in particular, with determination of the structure of signals and processes with resolution in the pico- and femtosecond range. The scheme used for the analysis is based on registration of four spatially separated spectra of the studied radiation. The spectra are formed in a four-channel scheme with a twin-wave Michelson interferometer and a spectral device. Modulators based on electrooptical crystals (perovskites) are placed in the channels. The sum spectra are formed: without modulators, with the effect of either of the modulators, and with both of them affecting the radiation. The effect of the studied substance implies either modulating the radiation (in this case it is described by multiplication) or redistributing the radiation (then it is described by convolution).     

Preparation and characterization of acrylic‐based black particles of poly(methyl methacrylate‐co‐ethylene glycol dimethacrylate) by dispersion polymerization for electrophoretic displays

Ultrafine black particles, ranging in diameter from 1 to 3 μm, were prepared by dispersion polymerization in a methanol/water mixture with vinyl monomers, nonpolymerizable Sudan black B dyes, and fluorescein isothiocyanate labeled charge control additives. Both the ratio of the methanol to the water dispersion medium and the polymeric stabilizer concentration had significant effects on the particle size. The important role of the stabilizer concentration lay in the particle formation step, during which it determined the particle stability and final particle size. These could affect the extent of the aggregation of nuclei by changing the adsorption rate of the stabilizer and the viscosity of the dispersion medium, resulting in smaller particles. The fluorescent‐labeled charge control additives strongly affected the electrophoretic mobility. A small concentration of fluorescent‐labeled charge control additives increased the electrophoretic mobility. However, a further addition reduced the electrophoretic mobility of the polymer particles. The concentration dependence of the fluorescent‐labeled charge control additives on the deposition behavior in the polymer particles was successfully imaged and thereafter quantified by image analysis. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5608–5616, 2004     

Magnetic poly(glycidyl methacrylate) microspheres prepared by dispersion polymerization in the presence of electrostatically stabilized ferrofluids

Fine magnetite nanoparticles, both electrostatically stabilized and nonstabilized, were synthesized in situ by precipitation of Fe(II) and Fe(III) salts in alkaline medium. Magnetic poly(glycidyl methacrylate) (PGMA) microspheres with core‐shell structure, where Fe₃O₄ is the magnetic core and PGMA is the shell, were obtained by dispersion polymerization initiated with 2,2′‐azobisisobutyronitrile (AIBN), 4,4′‐azobis(4‐cyanovaleric acid) (ACVA), or ammonium persulfate (APS) in ethanol containing poly(vinylpyrrolidone) or ethylcellulose stabilizer in the presence of iron oxide ferrofluid. The average microsphere size ranged from 100 nm to 2 μm. The effects of the nature of ferrofluid, polymerization temperature, monomer, initiator, and stabilizer concentration on the PGMA particle size and polydispersity were studied. The particles contained 2–24 wt % of iron. AIBN produced larger microspheres than APS or ACVA. Polymers encapsulating electrostatically stabilized iron oxide particles contained lower amounts of oxirane groups compared with those obtained with untreated ferrofluid. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5827–5837, 2004     

Φ520mmF/1.6椭球面反射镜加工

介绍了一块Φ520mm大相对孔径(F/1.6)轻量化椭球面反射镜的加工与检测方法。镜面的有效口径为Φ502mm,顶点曲率半径为1600mm,非球面系数k=-0.9663,面形精度要求优于0.025λ(RMS)。镜子背面有54个大小深浅不一的不通孔,用于减轻镜子的重量。采用WYKO干涉仪检测得到镜面面形误差达RMS0.02λ,λ=632.8nm。     

基于成像机理的小波包变换多聚焦图像融合

由于可见光成像系统的聚焦范围有限,因而在成像过程中,除聚焦良好的物体能生成清晰的图像外,该物体前后一定距离外的所有物体都将呈现不同程度的模糊.为了获得场景内所有物体均清晰的图像,在分析了多聚焦图像成像机理的基础上,提出了一种基于小波包变换的融合方法.它是将成像系统先聚焦在一部分对象上,得到其清晰的图像;然后再将其聚焦在另一部分对象上,得到另一清晰的图像;最后把这两幅实验图像加以融合,从而获得场景内所有物体均清晰的图像.实验结果表明,基于小波包变换的融合方法能够将信号的频带进行多层次划分,对高频成分也能进一步地分解,可有效综合多聚焦图像.     

三维光晶格中玻色凝聚气体基态波函数及干涉演化

基于Gross-Pitaevskii方程，运用有效化学势概念，研究了囚禁在组合势(由磁阱和三维光 晶格组成)中玻色凝聚气体在三维光晶格中的分布规律，并由此得到玻色凝聚气体的归 一化基态波函数.在取消组合势和仅取消光晶格而保留磁阱的两种情况下，运用传播子方 法求解出玻色凝聚气体密度分布的解析表达式.取消组合势后，理论计算所得到的玻色凝聚 气体聚随时间的演化规律与Greiner等的实验结果相一致.仅取消光晶格而保留磁阱时，研 究表明玻色凝聚气体的干涉模式呈现周期性的振荡行为.此外，在磁阱为各向异性的情况下 ， 关键词： 玻色凝聚气体 磁阱 光晶格 干涉模式