单偏振控制器环形腔光纤激光器实验研究

理论分析了非线性偏振旋转环形腔作为类饱和可吸收体获得脉冲的物理机理。在光纤环形腔结构中,采用单个偏振控制器实现了非线性偏振旋转锁模,直接获得了脉冲宽度为131 fs的超短脉冲输出。实验中,采用性能稳定的976 nm半导体二极管激光器作为抽运源,使用高掺杂浓度的Er3 光纤为增益介质,通过调节偏振控制器,获得了光谱谱宽(3 dB带宽处)为23.5 nm的稳定锁模脉冲输出。脉冲中心波长为1535.9 nm,平均功率为5.91 mW,脉冲重复率为11.20 MHz。     

氧化光栅型垂直腔面发射激光器的研究

通过分析矩形出光孔径和亚波长金属光栅结构,发现大孔径高功率垂直腔面发射激光器(VCSEL)的偏振控制的难点在于横模非常复杂。因此提出一种新型的氧化光栅型VCSEL结构,不仅能够很好地在有源区内引入各项异性的增益结构,并且最大的优势还在于能够完美地控制大孔径VCSEL的横模。通过有限元软件对器件有源区的电流分布进行了模拟,发现当光栅脊的宽度为1.8 μm时,载流子在光栅两端聚集的现象基本上可以消除,而且其电流密度分布差可以达到很高。     

利用半周期激光场调控H_2~+谐波辐射过程

采用数值求解核与电子耦合的薛定谔方程,对H_2~+分子谐波辐射调控进行了研究.计算结果表明,激光场正向时,谐波能量主要来源于负向H核贡献;激光场负向时,谐波能量主要来源于正向H核.随后,通过适当引入半周期激光场,可以有效调节正负H核辐射谐波的强度.最后,适当叠加谐波谱上的谐波,可获得一个46 as的脉冲.该研究对调控分子谐波的辐射过程及阿秒脉冲的输出是有帮助的.     

In situ measurement on nonuniform velocity distributionin external detonation exhaust flow by analysis ofspectrum features using TDLAS

Instantaneous and precise velocity sensing is a critical part of research on detonation mechanism and flow evolution.This paper presents a novel multi-projection tunable diode laser absorption spectroscopy solution,to provide a real-time and reliable measurement of velocity distribution in detonation exhaust flow with obvious nonuniformity.Relations are established between overlapped spectrums along probing beams and Gauss velocity distribution phantom according to the frequency shifts and tiny variations in components of light-of-sight absorbance profiles at low frequencies analyzed by the fast Fourier transform.With simulated optical measurement using H2O feature at 7185.6 cm-1 carried out on a phantom generated using a simulation of two-phase detonation by a two-fluid model,this method demonstrates a satisfying performance on recovery of velocity distribution profiles in supersonic flow even with a noise equivalent absorbance up to 2×10^-3.This method is applied to the analysis of rapidly decreasing velocity during a complete working cycle in the external flow field of an air-gasoline detonation tube operating at 25 Hz,and results show the velocity in the core flow field would be much larger than the arithmetic average from traditional tunable diode laser doppler velocimetry.This proposed velocity distribution sensor would reconstruct nonuniform velocity distribution of high-speed flow in low cost and simple operations,which broadens the possibility for applications in research on the formation and propagation of external flow filed of detonation tube.     

相位—啁啾调控对高次谐波光谱的影响

理论研究了在激光相位和啁啾调控共同影响下高次谐波光谱的变化。结果表明：当激光相位为0时,一阶啁啾调控使谐波能量延伸。二阶啁啾调控会呈现高强度谐波平台区。当激光相位为0.5π时,一阶啁啾调控可以获得连续平台区,但是强度较弱。在二阶啁啾调控下,谐波能量得到明显增大。通过谐波时频分析给出了不同激光波形下产生高次谐波光谱的原因。     

二极管泵浦激光器中泵浦光分布对激光器模式影响程度的计算方法

在激光器中,通常泵浦光呈不均匀分布,由此引起介质的增益也相应地出现不均匀分布,导致振荡光通过增益区时其分布发生变化。提出一种计算不均匀的泵浦光分布对于激光器内振荡光模式的影响程度,可以近似获得振荡光对原来场分布偏离的百分比的方法。在此基础上,对准连续运转的三向侧面泵浦激光器进行研究,分析不均匀泵浦光分布对振荡光场影响的规律。结果表明:当泵浦功率增加或谐振腔内损耗增加时,振荡光通过增益区时对原来分布的偏离程度也同时增加,呈单调变化关系;泵浦光不均匀分布对振荡光场的影响,与其沿振荡光轴向上的分布无关,仅仅取决于其在与振荡光垂直方向上的不均匀分布程度。通过计算还获得了此类效应的数量级,在2 000 W泵浦功率条件下,这种影响仅使振荡光偏离理想分布不到4%,而泵浦功率达到6 000 W时这种偏离则高达20%以上。     

熔石英后表面坑点型划痕对光场调制的近场模拟

建立了坑点型划痕的旋转抛物面模型, 用三维时域有限差分方法研究了熔石英后表面坑点型划痕随深度、 宽度、 间距以及酸蚀量变化对波长λ =355 nm入射激光的调制.研究表明, 这类划痕调制最强区位于相邻两坑点的连接区, 且越靠近表面调制越强.当其宽深比为2.0---3.5、 坑点间距约为坑点宽度的1/2时, 可获得最大光场调制, 最大光强增强因子(LIEF)为11.53; 当坑点间距大于坑点宽度时, 其调制大为减弱, 相当于单坑的场调制.对宽为60δ (δ =λ/12), 深和间距均为30δ的坑点型划痕进行刻蚀模拟, 刻蚀过程中最大LIEF为11.0, 当间距小于300 nm时, 相邻坑点由于衍射形成场贯通.     

Two localized CO2 laser treatment methods for mitigation of UV damage growth in fused silica

Two methods：high-power,short-time,single-shot irradiation（Method A） and low-power,long-time,multi-shot irradiation（Method B） are investigated to mitigate the UV damage growth in fused silica by using a 10.6-μm CO2 laser.To verify the mitigation effect of the two methods,the laser induced damage thresholds（LIDTs） of the mitigated sites are tested with a 355-nm,6.4-ns Nd：YAG laser,and the light modulation of the mitigation sites are tested with a 351-nm continuous Nd：YLF laser.The mitigated damaged sites treated with the two methods have almost the same LIDTs,which can recover to the level of pristine material.Compared with Method A,Method B produces mitigated sites with low crater depth and weak light modulation.In addition,there is no raised rim or re-deposited debris formed around the crater edge for Method B.Theoretical calculation is utilized to evaluate the central temperature of the CO2 laser beam irradiated zone and the radius of the crater.It is indicated that the calculated results are consistent with the experimental results.     

飞秒激光高精细加工柴油机喷油嘴倒锥孔法

利用飞秒激光加工热效应小、高精细、对材料无选择性等特点,针对柴油发动机高压共轨系统中关键零件——喷油嘴偶件喷油孔的加工需求,设计了一种利用三光楔扫描的飞秒激光加工装置,并进行了喷油嘴倒锥孔加工工艺研究.采用微孔三座标测量机(测量准确度1.2μm)对倒锥孔尺寸准确度进行检测,通过喷油嘴高压液体流量试验台(测量准确度±0.1%)对批量制孔后的油嘴进行了流量测试,结果表明:所设计装置加工的油嘴性能可以满足欧V排放法规的应用要求,对提升汽车制造业水平及柴油车排放标准具有重要意义.     

Short Tm3+-doped fiber lasers with watt-level output near 2 μm

High-power operation of diode-pumped fiber lasers at wavelength near 2μm are demonstrated with short length of heavily Tm3 -doped silica glass fibers. With 7-cm long fiber, a laser at near 2 μm is obtained with the threshold of 135 mW, maximum output power of 1.09 W, and slope efficiency of 9.6% with respect to the launched power from a laser diode at 790 nm. The output stability of this fiber laser is within 5%.The dependence of the performance of fiber lasers on the operation temperature and cavity configuration parameters is also investigated.