Full-Wave Analyses for a Multi-Layered Microstrip Patch Antenna

This paper describes numerical modelling of a dual band multi-layered microstrip patch antenna operating at 35GHz on an in-house semi-insulating GaAs substrate. The simulated and measured resonant frequencies at both lower and upper resonant frequencies will be compared to check the accuracy of the different numerical modelling techniques.     

Fluorinated,crosslinkable terpolymers based on vinylidene fluoride and bearing sulfonic acid side groups for fuel‐cell membranes

The radical terpolymerization of 8‐bromo‐1H,1H,2H‐perfluorooct‐1‐ene with vinylidene fluoride (VDF) and perfluoro(4‐methyl‐3,6‐dioxaoct‐7‐ene) sulfonyl fluoride is presented. Changing the feed compositions of these three fluorinated comonomers enabled us to obtain different random‐type poly[vinylidene fluoride‐ter‐perfluoro(4‐methyl‐3,6‐dioxaoct‐7‐ene) sulfonyl fluoride‐ter‐8‐bromo‐1H,1H,2H‐perfluorooct‐1‐ene] terpolymers containing various sulfonyl fluoride and brominated side groups. Yields higher than 70% were reached in all cases. The hydrolysis of the sulfonyl fluoride group into the ? SO₃Li function in the presence of lithium carbonate was quantitatively achieved without the content of VDF being affected, and so dehydrofluorination of the VDF base unit was avoided. These original terpolymers were then crosslinked via dangling bromine atoms in the presence of a peroxide/triallyl isocyanurate system, which produced films insoluble in organic solvents such as acetone and dimethylformamide (which totally dissolved uncured terpolymers). The acidification of ? SO₃Li into the ? SO₃H function enabled protonic membranes to be obtained. The thermal stabilities of the crosslinked materials were higher than those of the uncured terpolymers, and their electrochemical performances were investigated. According to the contents of the sulfonic acid side functions, the ion‐exchange capacities ranged from 0.6 to 1.5 mequiv of H⁺/g, whereas the water uptake and conductivities ranged from 5–26% (±11%) and from 0.5 to 6.0 mS/cm, respectively. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4566–4578, 2006     

Smaller Output Beam Divergence in the Slowly Opened Q-Switch Operation

The mechanism of the slowly opened Q-switch operation was investigated thoroughly. Maximum energy extraction from the resonator could be optimized, and the smallest output beam divergence could be achieved. In this article, we present a detailed analysis that has numerically verified the mode-selection mechanism in the slowly opened Q-switch operation, and the degree of the smaller output laser beam divergence that has been achieved. The mechanism of the slowly opened Q-switch operation is the inherent advantage of the passive saturable absorber in this operation. We can use the maximum energy extraction and the smallest output beam divergence results of the slowly opened Q-switch operation to design and optimize various passive saturable absorbers: plastic dye sheets, LiF:F₂⁻ color center crystals, Cr4⁺: YAG crystals, RG1000 color glass filters, and the single crystal semiconductor saturable absorber wafers that are in developed in our microchip laser systems.     

Chemically modified proton‐conducting membranes based on sulfonated polyimides: Improved water stability and fuel‐cell performance

A series of branched/crosslinked sulfonated polyimide (B/C‐SPI) membranes were prepared and evaluated as proton‐conducting ionomers based on the new concept of in situ crosslinking from sulfonated polyimide (SPI) oligomers and triamine monomers. Chemical branching and crosslinking in SPI oligomers with 1,3,5‐tris(4‐aminophenoxy)benzene as a crosslinker gave the polymer membranes very good water stability and mechanical properties under an accelerated aging treatment in water at 130 °C, despite their high ion‐exchange capacity (2.2–2.6 mequiv g^?1). The resulting polymer electrolytes displayed high proton conductivities of 0.2–0.3 S cm^?1 at 120 °C in water and reasonably high conductivities of 0.02–0.03 S cm^?1 at 50% relative humidity. In a single H₂/O₂ fuel‐cell system at 90 °C, they exhibited high fuel‐cell performances comparable to those of Nafion 112. The B/C‐SPI membranes also displayed good performances in a direct methanol fuel cell with methanol concentrations as high as 50 wt % that were superior to those of Nafion 112. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3751–3762, 2006     

Polymer electrolyte membranes for the direct methanol fuel cell: A review

The direct methanol fuel cell (DMFC) has the potential to replace lithium‐ion rechargeable batteries in portable electronic devices, but currently experiences significant power density and efficiency losses due to high methanol crossover through polymer electrolyte membranes (PEMs). Numerous publications document the synthesis and characterization of new PEMs for the DMFC. This article reviews this research, transport phenomena in PEMs, and experimental techniques used to evaluate new PEMs for the DMFC. Although many PEMs do not show significant improvements over Nafion®, the benchmark PEM in DMFCs, experimental results show that several new PEMs exhibit lower methanol crossover at similar proton conductivities and/or higher DMFC power densities. These results and recommendations for future research are discussed. © 2006 Wiley Periodicals, Inc. J Polym Sci Parts B: Polym Phys 44: 2201–2225, 2006     

Mechanical endurance of polymer electrolyte membrane and PEM fuel cell durability

The life of proton exchange membrane fuel cells (PEMFC) is currently limited by the mechanical endurance of polymer electrolyte membranes and membrane electrode assemblies (MEAs). In this paper, the authors report recent experimental and modeling work toward understanding the mechanisms of delayed mechanical failures of polymer electrolyte membranes and MEAs under relevant PEMFC operating conditions. Mechanical breach of membranes/MEAs in the form of pinholes and tears has been frequently observed after long‐term or accelerated testing of PEMFC cells/stacks. Catastrophic failure of cell/stack due to rapid gas crossover shortly follows the mechanical breach. Ex situ mechanical characterizations were performed on MEAs after being subjected to the accelerated chemical aging and relative humidity (RH) cycling tests. The results showed significant reduction of MEA ductility manifested as drastically reduced strain‐to‐failure of the chemically aged and RH‐cycled MEAs. Postmortem analysis revealed the formation and growth of mechanical defects such as cracks and crazing in the membranes and MEAs. A finite element model was used to estimate stress/strain states of an edge‐constrained MEA under rapid RH variations. Damage metrics for accelerated testing and life prediction of PEMFCs are discussed. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2346–2357, 2006     

Sulfonated poly(aryl ether ether ketone ketone)s containing fluorinated moieties as proton exchange membrane materials

A series of sulfonated poly(aryl ether ether ketone ketone)s statistical copolymers with high molecular weights were synthesized via an aromatic nucleophilic substitution polymerization. The sulfonation content (SC), defined as the number of sulfonic acid groups contained in an average repeat unit, could be controlled by the feed ratios of monomers. Flexible and strong membranes in sodium sulfonate form could be prepared by the solution casting method, and readily transformed to their proton forms by treating them in 2 N sulfuric acid. The polymers showed high T_gs, which increased with an increase in SC. Membranes prepared from the present sulfonated poly(ether ether ketone ketone) copolymers containing the hexafluoroisopropylidene moiety (SPEEKK‐6F) and copolymers containing the pendant 3,5‐ditrifluoromethylphenyl moiety (SPEEKK‐6FP) had lower water uptakes and lower swelling ratios in comparison with previously prepared copolymers containing 6F units. All of the polymers possessed proton conductivities higher than 1 × 10^?2 S/cm at room temperature, and proton conductivity values of several polymers were comparable to that of Nafion at high relative humidity. Their thermal stability, oxidative stability, and mechanical properties were also evaluated. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2299–2310, 2006     

Radiation induced synthesis and swelling characterization of thermo-responsive N-isopropylacrylamide-co-ionic hydrogels

Two-component thermo-responsive hydrogels poly(N-isopropylacrylamide)-co-vinylbenzyltrimethylammonium chloride (NIPA-co-VBT) and poly(N-isopropylacrylamide)-co-p-sodium styrene sulphonate (NIPA-co-SSS) were prepared by using high energy gamma radiation. The gels were characterized by Fourier transformed infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and sol-gel analysis. The presence of ionic monomers in NIPA leads to lower gel content. Introduction of ionic components in the matrix enhanced swelling extent but caused slower volume transition. The swelling studies in alcohol indicated that swelling extent was function of polarity of the swelling medium and all gels followed the order water > methanol > ethanol > iso-propanol. In mixed co-solvents (water-alcohol), they exhibit complex reentrant behavior. The co-polymer gels containing VBT swelled faster and to higher extent than those containing SSS. The dynamic swelling studies indicated that diffusion of water in PNIPA gel shifts from Fickian for PNIPA to anomalous for NIPA-co-ionic gels also the mean swelling time (MST) decreases for gels containing ionic monomers.     

A procedure for measuring the flexibility of single wood-pulp fibres

A way of determining the flexibility of wood-pulp fibres is developed, which involves i) a precise measurement of the topology of single-fibres by using a confocal laser scanning microscope and ii) the measurement of the elastic modulus of the fibres by using a single-fibre fatigue cell. Reported in this paper are the initial results of tests carried out on black spruce fibres, which have been subjected to three different levels of mechanical refining energy, namely ∼1100, 2300, and 3500 kWh/t. It is found that the fibre flexibility rises significantly between the first and second energy levels, but it does not change to the same degree between the second and third ones. The described procedure of measuring the flexibility of fibres may be used to establish the appropriate refiner energy necessary for the production of a specific grade of paper. Russian translation published in Mekhanika Kompozitnykh Materialov, Vol. 42, No. 1, pp. 115–128, January–February, 2006.     

TNFa在血管内皮细胞ECV304中的靶向表达研究

在缺失了3'LTR U3区内病毒的启动子／增强子序列的逆转录病毒载体pLXSNd中,用血管内皮生长因子受体KDR的特异性启动子调控了TNFa在血管内细胞ECV304中的靶向表达。将构建的载体pLXSN-TNFa,pLXSNd-KDRp-TNFa和空载体pLXSN用PA317细胞包装后获得重组病毒,并用重组病毒分别感染NIH3T3细胞和ECV304细胞,培养物上清的ELISA结果证明,KDR启动子指导的TNFa在KDR阳性细胞ECV304中的表达量为在KDR阴性细胞NIH3T3中的表达量的8倍;而TR指导的TNFa在这两种细胞中的表达无明显差异,实现了TNFa在血管内皮细胞中的靶向表达,这可能为肿瘤基因治疗提供新途径。