船用pH计检定装置的研究

研制了船用pH计检定装置。以基准电压集成电路作为电压标准,以单片机为控制中心,组成船用pH计检定核心部分,控制船用pH计检定装置输出标准电位。检定装置的pH值输出范围:0～14.0000 pH;pH示值误差:0.0003 pH;电压输出范围:-1999.99～+1999.99 mV;电压分辨率:0.01 mV;温度补偿范围:0～99.9℃。     

The Mediated Detection of Hydrogen Sulfide in Room Temperature Ionic Liquids

The detection of H₂S was studied using several mediators in room temperature ionic liquids (RTILs) at a microelectrode. Each mediator was characterised voltammetrically, and H₂S was added to observe if any mediation took place. A successful mediator was 3,5‐tert‐butyl‐obenzoquinone. Cyclic voltammetry was carried out in [C₂mim][NTf2]. A reductive wave was observed and attributed to the two‐electron reduction of the mediator. No oxidative signal was observed. H₂S was flowed through the system. Cyclic voltammograms showed a decrease in the reductive wave of the mediator and the onset of an oxidative signal due to the reaction between the mediator and H₂S to form an adduct. This reaction is reversible and on purging the system with N₂, the original reductive signal of the mediator was recovered.     

The influence of sulfonation degree on the thermal behaviour of sulfonated poly(arylene ethersulfone)s

Initial decomposition temperature (T_i), apparent activation energy of degradation (E_a) and glass transition temperature (T_g) of some low molar mass (M_n ≈ 8000 g mol⁻¹) sulfonated poly(arylene ethersulfone)s s-(PAES)s were determined to check their dependence on sulfonation degree (SD). The results obtained were compared with those for unsulfonated poly(arylene ethersulfone) PAES. In order to have an accurate control of the chemical structure, a pre-sulfonation route was followed for the preparation of sulfonated compounds. The thermal behaviour of the investigated s-(PAES)s as well as that of PAES appears not to be influenced by the environment (flowing nitrogen or static air atmosphere) of degradation. Both T_i and T_g values of s-(PAES)s were higher than those of PAES and increased quite linearly as a function of sulfonation degree. An analogous linear trend was observed for the apparent degradation energy of s-(PAES)s, but the values found were largely lower than those of unsulfonated homopolymer. The results are discussed and interpreted.     

An in situ temperature‐programmed XPS study of the surface chemical reactions of thiophene with Ag/titania

The Ag/titania sorbent for the ultradeep desulfurization of liquid fuels was characterized by electron spin resonance and was found to contain nearly the stoichiometric titania, without significant concentration of Ti³⁺ or the reactive oxygen species. The surface chemical reactions of thiophene adsorbed on the Ag/titania were studied by temperature‐programmed XPS from 25 to 525 °C upon in situ thermal annealing in high vacuum and in situ oxidation by oxygen gas. The titania support is not chemically reactive under those conditions. Silver oxide in the Ag/titania sorbent is converted to Ag₂ S without formation of the transient surface sulfates or sulfites and is further oxidized by molecular oxygen. Copyright © 2010 John Wiley & Sons, Ltd.     

Thermoelectric properties of HPHT sintered In-doped Pb0.5Sn0.5Te

The thermoelectric properties of Pb_0.5Sn_0.5Te doped with In at 1.0, 2.0, and 3.0×10¹⁹/cm³ and sintered at a high pressure and high temperature (HPHT) of 4.0 GPa and 800 or 900 °C, respectively, have been studied. All samples show p-type semiconducting behavior with positive thermopower. We find that HPHT sintering of conventionally synthesized materials improves their thermoelectric properties. The highest power factor is obtained for In doping of 2.0×10¹⁹/cm³ with 13.5 μW/cm K² at 230 °C. The corresponding figure of merit is 1.43×10⁻³/K. This represents a twofold improvement in thermoelectric figure of merit, compared to the conventionally sintered materials reported in the literature. When exposed to 400 °C for 10 days, samples sintered at 900 °C exhibit more stable thermoelectric properties, while the properties of those sintered at 800 °C deteriorated. These results demonstrate that HPHT sintering is a viable and controllable way of tuning the thermoelectric properties of PbTe-based materials.     

Synthesis of boron suboxide (B6O) with ball milled boron oxide (B2O3) under lower pressure and temperature

Boron reacted with ball milled boron oxide under pressures between 1 and 5 GPa and at temperatures between 1300 and 1700 °C to afford boron suboxide (B₆O). Icosahedral B₆O grains with diameters ranging from 100 nm to 1.3 μm were prepared. The factors that affect the synthesis of B₆O are investigated. The best sample with crystal size up to 1.3 μm is obtained at 2 GPa and 1400 °C for 6 h. The indentation experiment gave an average Vickers hardness of 32.3 GPa for bulk B₆O sample, which is consistent with previous reports. Bulk B₆O sample exhibits oxidation resistance in air up to 1000 °C and mild oxidation in the temperatures of 1000-1200 °C, which is more oxidation resistant than diamond. It is possible that B₆O could be used as a substitute for diamond in industry because of its relatively mild synthesis conditions, high thermal stability and high hardness.     

Current Rectification in Temperature‐Responsive Single Nanopores

Herein we demonstrate a fully abiotic smart single‐nanopore device that rectifies ionic current in response to the temperature. The temperature‐responsive nanopore ionic rectifier can be switched between a rectifying state below 34 °C and a non‐rectifying state above 38 °C actuated by the phase transition of the poly(N‐isopropylacrylamide) [PNIPAM] brushes. On the rectifying state, the rectifying efficiency can be enhanced by the dehydration of the attached PNIPAM brushes below the LCST. When the PNIPAM brushes have sufficiently collapsed, the nanopore switches to the non‐rectifying state. The concept of the temperature‐responsive current rectification in chemically‐modified nanopores paves a new way for controlling the preferential direction of the ion transport in nanofluidics by modulating the temperature, which has the potential to build novel nanomachines with smart fluidic communication functions for future lab‐on‐chip devices.     

Dual crosslinked pH‐ and temperature‐sensitive hydrogel beads for intestine‐targeted controlled release

Novel drug‐loaded hydrogel beads for intestine‐targeted controlled release were developed by using pH‐ and temperature‐sensitive carboxymethyl chitosan‐graft‐poly(N,N‐diethylacrylamide) (CMCTS‐g‐PDEA) hydrogel as carriers and vitamin B₂ (VB₂) as a model drug. The hydrogel beads were prepared based on Ca²⁺ ionic crosslinking in acidic solution and formed dual crosslinked network structure. The structure of hydrogel and morphology of drug‐loaded beads were characterized by Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), and scanning electron microscopy (SEM). The study about swelling characteristics of hydrogel beads indicated that the beads had obvious pH‐ and temperature‐sensitivity. In vitro release studies of drug‐loaded beads were carried out in pH 1.2 HCl buffer solution and pH 7.4 phosphate buffer solution at 37°C, respectively. The results indicated that the dual crosslinked method could effectively control the drug release rate under gastrointestinal tract (GIT) conditions, which was superior to traditional single crosslinked beads. In addition, the effects of grafting percentage, pH value, and temperature on the release behavior of the VB₂ were investigated. The drug release mechanism of CMCTS‐g‐PDEA drug‐loaded beads was analyzed by Peppa's potential equation. According to this study, the dual crosslinked hydrogel beads based on CMCTS‐g‐PDEA could serve as suitable candidate for drug site‐specific carrier in intestine. Copyright © 2009 John Wiley & Sons, Ltd.     

晋城无烟煤加压快速热解特性及其对气化反应的影响

利用自行设计的加压热重固定床反应器进行了晋城无烟煤加压快速热解特性的研究,并结合热天平半焦等温热失重分析,考察了热解温度、停留时间和热解压力等外部操作条件对煤焦快速热解半焦特性的影响。结果表明,随热解温度的提高、停留时间的延长和热解压力的增大,所得到的半焦产率降低,气化反应性减弱,活化能提高;高温产生较小的比表面积,而停留时间的延长和压力的提高产生较大的比表面积,比表面积与气化反应速率无明显的依存关系。水蒸气气化速率是CO2的四倍左右。     

高温下煤焦的碳微晶及孔结构的演变行为

以贵州煤为原料,在热解温度950℃~1400℃制备了各种慢速和快速热解焦,主要对高温热解过程中煤焦的碳微晶和孔结构的演变行为进行了研究,同时也研究了高温气化过程中煤焦的孔结构变化规律。结果表明,慢速热解焦和快速热解焦的C和H含量明显不同;随热解温度的升高,煤焦的碳微晶结构向有序化方向发展,但慢速热解煤焦比快速热解煤焦的"石墨化"程度大;快速热解煤焦的微孔比表面积和微孔容积明显高于慢速热解煤焦,即快速热解煤焦的孔隙结构明显比慢速热解煤焦发达;在气化反应初期,煤焦的微孔比表面积下降,微中孔比表面积增加,反应后期煤焦的总比表面积快速下降。