基于CCD的无接触式的物体测量

基于CCD的物体测量平台，首先对物体图像进行预处理，继而利用Canny算子提取物体边缘，再通过本文改进的Hough变换实现对被测物体边界直线检测和重构，最后通过多项式插值算法实现物体像素尺寸到物体实际尺寸的转换．实验证明，此方法能够实现无接触式物体尺寸较高精度的测量．     

Studies on recoil proton tracks in NTA films with the T(d,n)He reaction

Recoil proton tracks in nuclear emulsion are counted by scanning them using strip, square or circular field of view of optical microscope. In this paper, the overestimate due to the edge effects in counting recoil proton tracks at different neutron energies produced from the T(d,n)⁴He reaction has been determined by measuring the true track density in NTA film. The overestimate has also been calculated using the measured value of the mean projected track length (L) in the film. The percentage of measured overestimates has been compared with those obtained by calculation and the results agree reasonably well. Fading effect in NTA film has been studied and found to be 22% more in the summer than in the winter season. A great reduction in fading rate could be achieved if the films are desiccated and sealed in highly pure dry nitrogen maintained at an over-pressure of 1000 Pa to reduce water vapour ingress. After the edge effect correction, the sensitivity of NTA film has been calculated from (1.72±0.08)×10⁻³ tracksn⁻¹ to (1.97±0.16)×10⁻³ tracksn⁻¹ in the neutron energy ranges from 15.91 to 18.88 MeV. The response was found to be from 0.24±0.02 trackscm⁻² permSv to 0.26±0.01 trackscm⁻² permSv in the same energy range.     

聚心火焰在共振腔作用下引发爆轰的数值研究

 基于带化学反应的二维轴对称Euler方程，利用带有Superbee限制函数的波传播算法，对共振腔中的氢气-空气预混气的聚心燃烧进行了数值模拟，讨论了共振腔不同抛物面对起爆的影响。数值结果表明，在开始阶段，燃烧诱导的激波在轴心、火焰和固壁的反射，使火焰失稳，随后共振腔中的抛物壁面上产生一定频率和强度的反射激波，不断穿越火焰，使火焰进一步失稳，加剧了燃烧速度，最终导致爆轰的形成。同时，火焰在与激波的作用过程中，形状扭曲变形，呈封闭端小敞口端大的扁平头部蘑菇云。共振腔抛物面的不同形状引起激波聚焦位置的变化，会影响激波和火焰的相互作用，使起爆提前或推迟，甚至不起爆。     

火焰辐射及偶丝导热对热电偶测温影响的数值分析

本文利用层流同向扩散乙烯火焰的数值模拟结果,根据所得的火焰温度场、气体速度场、火焰辐射场,分析火焰辐射、热电偶偶丝导热对热电偶测温的影响.结果表明在火焰的低温区火焰辐射要大于节点向外辐射,节点得到的能量要高于节点损失的能量,因此在火焰的低温区节点温度要高于当地的气体温度;同时直径为100μm的热电偶存在较大的导热,对节点温度测量有较大的影响.     

微小圆管中分裂火焰的实验与理论研究

对丙烷/空气在内径2 mm的圆管内的预混燃烧进行了实验研究,借助于高速数码摄像机发现了分裂火焰现象,其中一个为向上游传播的较亮的常规火焰,另一个为向下游传播的较暗的微弱火焰。这些火焰先后熄灭,经过一段时间后又重复发生自着火、分裂、反向传播、灭火过程。这种现象在富燃、化学恰当比以及贫燃火焰中都有存在。一维非稳态计算表明化...     

火焰曲率对H_2扩散火焰NO排放影响的数值研究

使用不同的H_2/O_2化学反应机理和NO_x化学反应机理模拟了平面对冲火焰。通过和实验数据比较确定了最优的化学反应机理。使用该化学反应机理模拟了管形对冲火焰。通过对比平面拉伸火焰和管形拉伸火焰,突出了火焰曲率对H_2扩散火焰温度和NO排放的影响。分析显示正曲率提高火焰温度,负曲率降低火焰温度,由于NO生成对温度的敏感性,正曲率火焰的NO排放明显高于平面火焰,反之,负曲率火焰的NO排放大大低于平面火焰。     

Uniform theory of the boundary diffraction wave

A uniform version of the potential function of the Maggi-Rubinowicz boundary diffraction wave theory is obtained by using the large argument expansion of the Fresnel integral. The derived function is obtained for the problem of diffraction of plane waves by a circular edge. The results are plotted numerically.     

Experimental and numerical study of a conical turbulent partially premixed flame

The structure and dynamics of a turbulent partially premixed methane/air flame in a conical burner were investigated using laser diagnostics and large-eddy simulations (LES). The flame structure inside the cone was characterized in detail using LES based on a two-scalar flamelet model, with the mixture fraction for the mixing field and level-set G-function for the partially premixed flame front propagation. In addition, planar laser induced florescence (PLIF) of CH and chemiluminescence imaging with high speed video were performed through a glass cone. CH and CH₂O PLIF were also used to examine the flame structures above the cone. It is shown that in the entire flame the CH layer remains very thin, whereas the CH₂O layer is rather thick. The flame is stabilized inside the cone a short distance above the nozzle. The stabilization of the flame can be simulated by the triple-flame model but not the flamelet-quenching model. The results show that flame stabilization in the cone is a result of premixed flame front propagation and flow reversal near the wall of the cone which is deemed to be dependent on the cone angle. Flamelet based LES is shown to capture the measured CH structures whereas the predicted CH₂O structure is somewhat thinner than the experiments.     

Organo-modified magnesium hydroxide nano-needle and its polystyrene nanocomposite

Acrylic acid modified magnesium hydroxide nano-needles (AA–Mg(OH)₂) had been synthesized by alkaline injected into magnesium chloride solution at about 0°C in the presence of acrylic acid (AA). Then the polystyrene/magnesium hydroxide nano-needles composite (PS/Mg(OH)₂) had been prepared by the radical copolymerization with styrene in toluene system using AA–Mg(OH)₂ as a macro-monomer. The elemental analysis (EA) and Fourier transform infrared (FTIR) analyses show that the polystyrene had been grafted onto the surfaces of the nano-needles (AA–Mg(OH)₂). The nano-needles (AA–Mg(OH)₂) had better dispersibility in polystyrene matrix as observed by transmission electron microscope (TEM) analysis. The thermal behavior analysis results from the differential scanning calorimetry (DSC) indicated that the magnesium hydroxide nano-needles had lower thermal decomposition temperature than that of the polymer matrix and it is expected that the nano-needles prepared by the proposed method could be used as an environmental-friendly flame retardant.