Ultrahigh‐molecular‐weight‐polyethylene‐fiber surface treatment by electron‐beam‐irradiation‐induced graft polymerization and its effect on adhesion in a styrene–butadiene rubber matrix

Aiming to develop a high‐performance fiber‐reinforced rubber from styrene–butadiene rubber (SBR), we applied a special technique using electron‐beam (EB)‐irradiation‐induced graft polymerization to ultrahigh‐molecular‐weight‐polyethylene (UHMWPE) fibers. The molecular interaction between the grafted UHMWPE fibers and an SBR matrix was studied through the evaluation of the adhesive behavior of the fibers in the SBR matrix. Although UHMWPE was chemically inert, two monomers, styrene and N‐vinyl formamide (NVF), were examined for graft polymerization onto the UHMWPE fiber surface. Styrene was not effective, but NVF was graft‐polymerized onto the UHMWPE fibers with this special method. A methanol/water mixture and dioxane were used as solvents for NVF, and the effects of the solvents on the grafting percentage of NVF were also examined. The methanol/water mixture was more effective. A grafting percentage of 16.4% was the highest obtained. This improved the adhesive force threefold with respect to that of untreated UHMWPE fibers. These results demonstrated that EB irradiation enabled graft polymerization to occur even on the inert surface of UHMWPE fibers. However, the mechanical properties of the fibers could be compromised according to the dose of EB irradiation. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2595–2603, 2004     

Surface polarity of cellulose derivates observed by coumarin 151 and 153 as solvatochromic and fluorochromic probes

Solvent‐dependent ultraviolet–visible (UV–vis) absorption and Stokes shifts including strong hydrogen‐bond‐donating (HBD) solvents such as 2,2,2‐trifluoroethanol and 1,1,1,3,3,3‐hexafluoro‐2‐propanol of two coumarine dyes (Co 151 and Co 153) were analyzed with multiple‐square analyses of linear solvation energy relationships and the Kamlet–Taft solvent parameter set to α (HBD capacity), β (hydrogen‐bond‐accepting capacity), and π* (dipolarity/polarizability). The UV–vis absorption and emission spectra of Co 151 and Co 153 were measured when adsorbed on various polysaccharides such as different cellulose batches, carboxymethylcelluloses with different degrees of substitution, and chitine. As a result of this evaluation, Co 153 is recommended as an alternative UV–vis probe for evaluating the dipolarity/polarizability of cellulose and cellulose derivates. Multiple adsorption of Co 153 on Linters cellulose took place indicating a wide‐surface polarity distribution, which makes the determination of a rigid polarity parameter questionable. Thus, fluorescence measurements of adsorbed Co 153 are suitable to detect inhomogenities on a surface but not for the determination of empirical polarity parameters. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1210–1218, 2003     

A microspectroscopic study of the electronic homogeneity of ordered and disordered Sr2FeMoO6

Disordered Sr₂FeMoO₆ shows a drastic reduction in saturation magnetization compared to highly ordered samples, moreover magnetization as a function of the temperature for different disordered samples shows qualitatively different behaviours. We investigate the origin of such diversity by performing spatially resolved photoemission spectroscopy on various disordered samples. Our results establish that e_xtensive electronic inhomogeneity, arising most probably from an underlying chemical inhomogeneity in disordered samples, is responsible for the observed magnetic inhomogeneity. It is further pointed out that these inhomogeneities are connected with composition fluctuations of the type Sr₂Fe_1+x Mo_1-x O₆ with Fe-rich (x > 0) and Mo-rich (x < 0) regions. Dedicated to Prof J Gopalakrishnan on his 62nd birthday.     

Synthesis and characterization of polyaniline doped with organic acids

Spectroscopic [UV–visible and Fourier transform IR (FTIR)] and thermal properties of chemically synthesized polyanilines are found to be affected by varying the protonation media (acetic, citric, oxalic, and tartaric acid). The optical spectra show the presence of a greater fraction of fully oxidized insulating pernigraniline phase in polyaniline doped with acetic acid. In contrast, the selectivity in the formation of the conducting phase is higher in oxalic acid as a protonic acid media. The FTIR spectra of these polymers reveal a higher ratio of the relative intensities of the quinoid to benzenoid ring modes in acetic acid doped polyaniline. Scanning electron micrographs revealed a sponge‐like structure derived from the aggregation of the small granules in acetic acid and oxalic acid doped polyaniline. A three‐step decomposition pattern is observed in all the polymers, regardless of the protonic acid used for the doping. The second step loss related to the loss of dopant is found to be higher in the oxalic acid doped polymer. In accordance with these results the conductivity is also found to be higher in oxalic acid doped material. The temperature dependent conductivity measurements show the thermal activated behavior in all the polymers. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2043–2049, 2004     

Hybrid organosilazane/organosilylamine telechelic oligomers—I. Two-dimensional NMR spectroscopy characterization of dimethylsilylethylenediamine oligomers

The detailed characterization of multifunctional hybrid organosilazane/organosilylamine telechelic oligomers by IR and ¹H, ¹³C and ²⁹Si NMR spectroscopy in one and two dimenions has been undertaken. The specific multifunctional oligomers, comprising NH/NH₂ or SiCl functionalities depending on the monomer feed-ratio, were prepared from mono- and di-functionally reacted dichlorodimethylsilane (DDS) and mono-, di-, tri- and tetra-functionally reacted ethylenediamine (EDA). Varying the feed-ratio afforded control of the microstructures of the oligomers and the preparation of oligomers with, in some cases, conterminously located silicon–chlorine (SiCl) groups. The combination of the NMR methods with the IR technique has enabled the detailed microstructural characterization of the oligomers and the identification of the functionalities therein. This approach and the knowledge gained from the DDS/EDA system has been applied to the microstructural characterization of other hybrid organosilazane/silylamine preceramic telechelic oligomers.     

超稳Y沸石制备技术对沸石铝分布的影响 Ⅱ.均匀铝分布的超稳Y沸石的制备

对水热处理后得到的USY沸石作进一步的酸处理以及采用改进的氟硅酸盐溶液骨架富硅工艺,分别得到了经XPS剖面分析证实为铝分布均匀的超稳Y沸石HAY-Ⅰ和HAY-Ⅱ。IR分析表明,在酸处理过程中从USY沸石中去掉的那部分非骨架铝类与3690cm~(-1)处羟基有关,仍残留在HAY-Ⅰ沸石中的那部分非骨架铝类与3670cm~(-1)和3600cm~(-1)处羟基有关。XRD和化学分析表明HAY-Ⅰ沸石仍含有约50％的非骨架铝类,而HAY-Ⅱ沸石则基本上不含非骨架铝类,HAY-Ⅱ沸石还显示更高的结晶保留度。DTA分析表明,HAY-Ⅰ和HAY-Ⅱ两种沸石的热稳定性均高于USY沸石。     

Complexes in polymers IV. FTIR microscopic characterization of thin organic polymer films containing embedded transition-metal carbonyl complexes

Thin films of polystyrene (PS), poly(methyl methacrylate) (PMMA) and polystyrene-polyacrylonitrile copolymer (PS-AN), containing various embedded transition-metal complexes, have been studied by FTIR microscopy. The spatial distributions of the transition-metal carbonyl complexes throughout the thin organic polymer films have been determined by a two-dimensional IR mapping procedure. The spectral variations observed in the distribution of the metal carbonyls throughout the different polymer films are discussed. The IR data show that the technique used to prepare the organometallic-embedded thin films (viz. freeze-drying of solutions followed by hot mechanical pressing of the residues) does in general lead to homogeneous films which may eventually find industrial application, e.g. as membrane sensors for small molecules.     

Poly(phenylene vinylene)‐based copolymers containing 3,7‐phenothiazylene and 2,6‐pyridylene chromophores: Fluorescence sensors for acids,metal ions,and oxidation

A novel copolymer, poly(N‐hexyl‐3,7‐phenothiazylene‐1,2‐ethenylene‐2,6‐pyridylene‐1,2‐ethenylene) ( P3 ), containing N‐hexyl‐3,7‐phenothiazylene and 2,6‐pyridylene chromophores was synthesized to investigate the effect of protonation, metal complexation, and chemical oxidation on its absorption and photoluminescence (PL). Poly(N‐hexyl‐3,8‐iminodibenzyl‐1,2‐ethenylene‐1,3‐phenylene‐1,2‐ethenylene) and poly(N‐hexyl‐3,7‐phenothiazylene‐1,2‐ethenylene‐1,3‐phenylene‐1,2‐ethenylene) ( P2 ), consisting of 1,3‐divinylbenzene alternated with N‐hexyl‐3,8‐iminodibenzyl and N‐hexyl‐3,7‐phenothiazylene, respectively, were also prepared for comparison. Electrochemical investigations revealed that P3 exhibited lower band gaps (2.34 eV) due to alternating donor and acceptor conjugated units (push–pull structure). The absorption and PL spectral variations of P3 were easily manipulated by protonation, metal chelation, and chemical oxidation. P3 displayed significant bathochromic shifts when protonated with trifluoroacetic acid in chloroform. The complexation of P3 with Fe³⁺ led to a significant absorption change and fluorescence quenching, and this implied the coordination of ferric ions with the 2,6‐pyridylene groups in the backbone. Moreover, both phenothiazylene‐containing P2 and P3 showed conspicuous PL quenching with a slight redshift when oxidized with NOBF₄. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1272–1284, 2004     

CO-laser photoacoustic detection of phosgene (COCl2)

Detection of COCl₂, a highly toxic gas in chemical industry, using laser photoacoustic spectroscopy is presented. The spectrophone system used has a broad band LN₂ cooled CW CO laser as a source of radiation, which operates from 4.8–8.4 um in the mid-infrared. Using an extracavity open longitudinal resonant cell, absorption signals to about 30 CO laser lines in the 5.45 um region could be observed. detection sensitivity has been estimated to be ppb order.This work has been supported by the NSFC     

Synthesis of functional polymers—Vinylidene fluoride based fluorinated copolymers and terpolymers bearing bromoaromatic side‐group

The radical co‐ and terpolymerization of 4‐[(α,β,β‐trifluorovinyl)oxy]bromo benzene (TFVOBB) with 1,1‐difluoroethylene (or vinylidene fluoride, VDF, or VF₂), hexafluoropropene (HFP), perfluoromethyl vinyl ether (PMVE), and chlorotrifluroroethylene (CTFE) is presented. Although TFVOBB could be thermocyclodimerized, it could not homopolymerize under radical initiation. TFVOBB could be copolymerized in solution under a radical initiator with VDF or CTFE comonomers, while its copolymerization with HFP or PMVE were unsuccessful. The terpolymerization of TFVOBB with VDF and HFP, or VDF and PMVE, or VDF and CTFE also led to original fluorinated terpolymers bearing bromoaromatic side‐groups. The conditions of co‐ and terpolymerization were optimized in terms of the nature of the radical initiators, and of the nature of solvents (fluorinated or nonhalogenated). Various monomer concentrations in the co‐ and terpolymers were assessed by ¹⁹F and ¹H‐NMR spectroscopy. The thermal and physico chemical properties were also studied. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5077–5097, 2004